Lilin VS212 User manual

System Architecture
Part D escri ption
Audio I n (mono ,
Power I n Jack (D C12V 10%)
Power L ED Indi cator
3.5mm p hone ja ck, Mic phone i n / Line in )
Audio O ut (mon o, 3.5m m phone j ack)
Video In J ack
Video Ou t jack (V ideo Lo oping )
RS-48 5 Conne ctor (S uppor t MLP2, P elco D/ Pp rotoc ol)
Alarm I n / Out Con necto r
Load De fault B utton
RJ-45 N etwor k Conne ctor
Indic ator LE Ds
Green : While c able of n etwor k is conn ectin g the LED i s lit.
Orang e: When d ata is co mmuni catin g, the LE D is flas hed.
Red: Wh en alar m is acti vated , the LED i s lit.
SD/SD HC Card S lot
±
1
1
2
3
4
5
6
7
8
9
10
11
12
ALARMACTLINK
SDCARD
VIDEOENCODER
AUDIO
GND
DIN
NO
..
COM.
NC..
+5VOUT
RS 485
- -
RS 485- +
IN OUT
AUDIO
VIDEOIN VIDEOOUT
POWERDC12V RESET LAN
2 3 4
5 6 87 9 101112
H.264 1CH VIDEO ENCODER
Ma nu al
Product Components
Part Description
Audio
4. Power Adaptor
Audio In (mono,
Power In Jack (DC12V 10%)
Power LED Indicator
3.5mm phone jack, Micphone in / Line in)
Audio Out (mono, 3.5mm phone jack)
Video In Jack
Video Out Jack (Video Looping)
RS-485 Connector (Support MLP2, Pelco D/P protocol)
Alarm In / Out Connector
Load Default Button
RJ-45 Network Connector
Indicator LEDs
Green: While cable of network is connecting the LED is lit.
Orange: When data is communicating, the LED is flashed.
Red: When alarm is activated, the LED is lit.
SD/SDHC Card Slot
±
1
66-VS212OOE-1
1
2
3
4
5
6
7
8
9
10
11
12
IPD552EX2.2/4.2 N/P
H.264 D1 IP Cameras
INSTRUCTION MANUAL
1. H.264 1CH Video Encoder
2. Instruction Manual
3. CD Software Pack
Video
Fast Dome
Camera
HUB
H.264 Video Encoder
RS-485
DC12V
ALARMACTLINK
SD CARD
VIDEO ENCODER
AUDIO
GND
DIN
N O. . COM.
N C. .
+5V OUT RS 485- - RS 485- +
IN OUT
AUDIO
VIDEO IN VIDEO OUT
POWERDC12V RESET LAN
2 3 4
5 6 87 9 101112
H.264 1CH VIDEO ENCODER
Manual

SpecificationsAlarm In/Out Terminal
Video Compression
Resolution
Frame Rate
Video Streaming
Video Bitrate
Users
Alarm Function
CPU, Memory
Security
Network Protocols
Mobile Phone and PDA
PC Requirement
Maintenance
Network Interface
System Integration
CMX
Video Display
OS
Video Input / Output
Audio Input / Output
Two-way Audio
SD Card Recording
Control Interface
Alarm Input / Output
Power Supply
Power Consumption
Operating Temperature
Operating Humidity
Dimension
Weight
H.264, Motion JPEG
960H: 960x480(NTSC) / 960x576(PAL), D1: 720x480, CIF: 352x240
H.264: up to 30/25 FPS at 960H resolution
Motion JPEG: up to 30/25 FPS at D1 resolution
Simultaneous Motion JPEG and H.264
RTP/HTTP, RTP/TCP, RTP/UDP, Multicast Streaming
128Kbps ~ 3Mbps
Frame rate and bit rate controllable on-the-fly
VBR / CBR / GOP supported
8 simultaneous users
Image upload over FTP and E-mail by motion detection
OS : Windows 2000, Windows XP, Windows Vista, Windows 7
Browser : Windows Internet Explore 6, 7, 8
CPU : Intel Pentium 4 1.8GHz or above
RAM : 1GB or above, Independent Display Card
Embedded SoC ARM11, 528MHz, 256MB DDR2, 256MB flash memory
Base64 HTTP encryption
Multiple user access levels with password protection
10 user accounts available
IP, TCP, UDP, HTTP, SMTP, NTP, DDNS, UPnP, FTP, ARP,
DHCP, PPPoE, DNS, Telnet, RTSP, RTCP, ONVIF
iPhone, iPad, and Android support
Firmware update via HTTP
10Mbps / 100Mbps, RJ-45
ONVIF & LILIN HTTP API
CMX HD3.6 support
LILIN Universal ActiveX & LILIN Java Applet
Embedded Linux 2.6.32
CVBS 1.0Vp-p, 75 , BNC connectorΩ
Mono, 1.4Vp-p, 50K , 3.5mm phone jackΩ
G.711 / PCM
Support SD/SDHC card for circular recording (card is not included)
RS-485, Half-Duplex, support MLP2, Pelco D/P protocols
Digital 1 input (TTL, +3~5V) / 2 Output (Relay, N.O./N.C.)
DC12V 10%±
4.5W
0 C ~ +50 C (32 F ~ 122 F)° ° ° °
20% ~ 80% (non-condensing)
136mm(D) x 130mm(W) x 44mm(H)
380g
H 264 1CH VIDEO EN C O DER.
Des i g n and speci f i cations ar e s ubject to ch a n ge withou t n o tice.
+5V COM. DIN
N.C. N.O.
1 2 3 4 5 6
GND
+5V Output: Max. output 50mA.
COM./N.O./N.C: Max. load AC24V/1A.
DIN terminal can be set either N.O. (normally open) or N.C. (normally
close) mode.
7 8
Emergency Factory Default
Use hardware to restore factory default settings, follow these steps:
1. Hold Load Default Button for 10 seconds, then release.
2. After about 40 seconds, the network LED light is off, and then lit.
3. This camera has completed the factory default settings, and then reboot.
4. Use IPScan software search for this IP device.
5. Using a Internet browser open the IP device.
6. Enter the default username "admin" and password "pass" to operate.
For the convenience of users, restore the factory default settings will revert to the default
IP address 192.168.0.200.
NOTE