Lilliput RM-1731S User manual

1
Important Safety Instructions:
Please read User Guide before using this product.
Please keep User Guide for future reference.
Please read the precaution to prevent possible danger and loss of property.
Precaution:
Please do not place the display screen towards the ground.
Please avoid heavy impact or drop onto the ground.
Please do not use chemical solutions to clean this product. Please wipe with a clean soft cloth to
maintain the brightness of the surface.
Please do not block any vent hole.
Please follow the instructions and trouble-shootings to adjust the product. Other improper adjustment
may result in damage. Any further adjustment must be performed or conducted by a qualified
technician.
Please unplug the power and remove the battery if long-term no-use, or thunder weather.

2
Contents
Important Safety Instructions: ................................................................................. 1
Precaution: .............................................................................................................. 1
1. Production Description ........................................................................................ 3
2. Menu Setting ....................................................................................................... 5
3. Product Parameters ........................................................................................... 16
4. Accessories ........................................................................................................ 16
5. Trouble Shooting................................................................................................ 17
Appendix 1: 3D LUT Loading................................................................................... 18
Appendix 2: Remote Terminal Instructions ............................................................ 21

3
1. Production Description
1.1Front Panel
1. Earphone Jack
2. POWER: Power ON/OFF.
3. SDI: Signal switch to SDI mode when light on. (Only available on SDI HDMI version）
4. HDMI: Signal switch to HDMI mode when light on. (Only available on SDI HDMI version）
5. MENU
Press to enter menu.
Press to enter option in the menu.
6. <
Select option in the menu.
Decrease the option value.
Before enter the menu, single press to activate function bar, press again to switch among of
①②③④⑤⑥⑦⑧⑨

4
volume, brightness, contrast, color, hue, sharpness and backlight.
7. >
Select option in the menu.
Increase the option value.
8. Exit Button
9. F1~F3 User definable buttons
Assigned function by factory as follow:
[F1]: Peaking [F2]: Waveform [F3]: Level Meter
（Long press any F1-F2-F3 buttons for 3-5 seconds to custom options.）
1.2 Rear Panel
1.2.1 Interfaces
1. 12V DC power port.
2. TALLY connecter.
3. SDI output port. (Only available on SDI HDMI Version)
4. SDI input port. (Only available on SDI HDMI Version)
5. HDMI output port.
6. HDMI input port.
7. USB port.
8. LAN port. (Connected to PC network interface for function adjustment.)
①②③④⑤ ⑥ ⑦ ⑧

5
2. Menu Setting
Before setting the functions, please make sure the device is connected correctly.
2.1 Shortcut keys
2.1.1 Function Menu
Under non menu screen, press < or > buttons to activate function bar, and then press the "MENU"
button can activate the shortcut menu bar to select brightness, contrast, saturation, tint, sharpness,
volume, back light.
Use the < or > button to adjust the value.
Default function is [Back Light].
2.1.2 F1-F2-F3 Buttons:
Long press any F1-F2-F3 buttons for 3-5 seconds to pop up shortcut menu on the
screen. As shown in Figure. Select option via < and > key, and set it as default via
pressing the Menu button, then press Exit button to exit shortcut setting menu.
Functions of F1-F2-F3 buttons can also be customized: [Center Marker], [Aspect
Marker], [Safety Marker], [Overscan], [Scan], [Aspect], [Anamorphic], [Camera Log],
[Check Field], [H/V Delay], [Freeze], [Image Flip], [Color Bar], [Peaking], [False
Color], [Exposure], [Histogram], [Waveform], [Vector], [TimeCode], [Mute], [ Lever
Meter]. (TimeCode only available on SDI mode.)
Default function:
F1: [Scan] F2: [Waveform]. F3: [Aspect]

6
3.2 MENU Operations
3.2.1 PICTURE
Brightness
Control the degree of brightness between 0-100.
Contrast
Control contrast ratio between 0-100.
Saturation
Adjust the color intensity between 0-100.
Tint
Adjust tint between 0-100.
Sharpness
Control sharpness of the image between 0-100.
Back Light
Adjust the level of the back light from 0 to 100.
RGB Range
Use this item to choose the RGB range of the HDMI input: [Full], [Limited].
Only available on HDMI mode.
HDMI EDID
Select the HDMI EDID from between [4K] and [2K]. This item enables PC or other devices to recognize
the property of this monitor and makes the images look excellent on the screen.
Only available on HDMI mode.

7
Camera Log
Use this item to choose one of the camera Log modes:
- [Off]: Turn off Camera Log.
- [Def. Log]: Use this item to choose one of the Camera Log modes as the following sequence:
[SLog2ToLC-709], [SLog2ToLC-709TA], [SLog2ToSLog2-709], [SLog2ToCine+709], [SLog3ToLC-709],
[SLog3ToLC-709TA], [SLog3ToSLog2-709], [SLog3ToCine+709], [ArriLogCTo709], [ArriLogCToP3DCI],
[CLogTo709], [VLogToV709], [JLogTo709], [JLogTo709HLG], [JLogTo709PQ], [Z7 NLogTo709], [D780
NLogTo709]
- [User Log]: Use this item to choose one of the User Log modes (1-6). Please install the User Log as
following steps:
The User Log must be named with. Cube in the suffix. Please note: the device only supports the format
of User Log: 17x17x17 / 33x33x33; Data order is BGR; Table order is BGR. If the format does not meet
the requirement, please use tool “Lut Tool.exe” to transform it.
Naming the User Log as User1-User6.cube, then copy the user Log into USB flash disk. Insert the USB
flash disk to the device, the User Log is saved to the device automatically at the first time. If the User
Log is not loaded for the first time, the device will pop up a prompt message, please choose whether
to update or not.
HDR
Use this item to choose one of the HDR presets: [Off], [ST 2084 300], [ST 2084 1000], [ST 2084 10000],
[HLG].

8
Color Temp.
Use this item to choose one of the color temperature presets: [5500K], [6500K], [7500K], [9300K],
[User].
Note: Only available under [User] mode to adjust R/G/B Gain and Offset.
R/G/B Gain
Adjust the R/G/B Gain of the current Color Temperature from 0 to 255. Default value: 128.
R/G/B Offset
Adjust the R/G/B Offset of the current Color Temperature from 0 to 511. Default value: 256.
3.2.2 MARKER
Center Marker
Select [On] to display the center marker “+” and [Off] not to display it.
Aspect Marker
Select the aspect ratio of the marker: [Off], [16:9], [1.85:1], [2.35:1], [2.39:1], [4:3], [3:2], [Grid], [User].
Note: When [Aspect Marker] is selected as [Grid], the safety marker and Aspect Mat cannot be displayed.

9
User Marker
H1/H2: Adjust the position of vertical markers from 1 to 1920 (Step value is 1).
V1/V2: Adjust the position of horizontal markers from 1 to 1080 (Step value is 1).
Note: User maker only in [Aspect Maker], [User] mode available.
Safety Marker
Select [Off] not to display the safety marker. When this item is used with the Aspect Marker, it is only
in Aspect Marker. When [Aspect Marker] is selected as [User], the safety marker does not be changed.
Select the size of the safety markers: [95%], [93%], [90%], [88%], [85%], [80%].
Marker Color
Select the color of marker displayed on the screen: [Red], [Green], [Blue], [White], and [Black].
Aspect Mat.
When activated, it can be selected from 1-7 (Step value is 1).
Thickness
Adjust the thickness of all the marker lines from 1-7 (Step value is 1).
3.2.3 FUNCTION
Scan
Adjust the scan mode among [Aspect], [Pixel To Pixel], [Zoom].