Lincoln Electric MAGNUM &MAGNUM PROCURVE 200 K497 User manual

MAGNUM & MAGNUM PRO CURVE 200
GMA GUN and CABLE ASSEMBLY
!"$&!$S%R '

November, 2010
%.32AF2=2;1@<;+<B
Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However,
your overall safety can be
increased by proper installation
... and thoughtful operation on
your part. ! !& %&
!"$&!$$"$&%
#'" &)&!'&$
 &% ' &
%&+"$'&! %! 
& &$!'!'& And,
most importantly, think before
you act and be careful.
Models 

• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: [phone] FAX: [phone] WEB SITE: www.lincolnelectric.com
• World's Leader in Welding and Cutting Products •
Copyright © Lincoln Global Inc.
®®
MAGNUM
MAGNUM PRO CURVE

!$  
=<D2?212>B6=:2;A
1.a. Turn the engine off before troubleshooting and maintenance
work unless the maintenance work requires it to be running.
____________________________________________________
1.b. Operate engines in open, well-ventilated
areas or vent the engine exhaust fumes
outdoors.
____________________________________________________
1.c. Do not add the fuel near an open flame
welding arc or when the engine is running.
Stop the engine and allow it to cool before
refueling to prevent spilled fuel from vaporiz-
ing on contact with hot engine parts and
igniting. Do not spill fuel when filling tank. If
fuel is spilled, wipe it up and do not start
engine until fumes have been eliminated.
____________________________________________________
1.d. eep all equipment safety guards, covers and devices in
position and in good repair. eep hands, hair, clothing and
tools away from V-belts, gears, fans and all other moving
parts when starting, operating or repairing equipment.
____________________________________________________
1.e. In some cases it may be necessary to remove safety
guards to perform required maintenance. Remove
guards only when necessary and replace them when the
maintenance requiring their removal is complete.
Always use the greatest care when working near moving
parts.
___________________________________________________
1.f. Do not put your hands near the engine fan.
Do not attempt to override the governor or
idler by pushing on the throttle control rods
while the engine is running.
___________________________________________________
1.g. To prevent accidentally starting gasoline engines while
turning the engine or welding generator during maintenance
work, disconnect the spark plug wires, distributor cap or
magneto wire as appropriate.
6
%&+
6
$)  ,$!'% "$!&&+!'$% !&$%$!"!%%%$!'% '$+!$&
"$ )+"$)$$%%!'! %'&)&&$!&!$!$!"$& 
Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you
purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box
351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available
from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.
%'$ &&   %&&!  !"$&!  &     $"$ "$!'$%$
"$!$! ++#' ('%
)$  
&$ 
 &%
:.F/21.;42?<B@
2.a. Electric current flowing through any conductor causes
localized Electric and Magnetic Fields (EMF). Welding
current creates EMF fields around welding cables and
welding machines
2.b. EMF fields may interfere with some pacemakers, and
welders having a pacemaker should consult their physician
before welding.
2.c. Exposure to EMF fields in welding may have other health
effects which are now not known.
2.d. All welders should use the following procedures in order to
minimize exposure to EMF fields from the welding circuit:
2.d.1. Route the electrode and work cables together - Secure
them with tape when possible.
2.d.2. Never coil the electrode lead around your body.
2.d.3. Do not place your body between the electrode and
work cables. If the electrode cable is on your right
side, the work cable should also be on your right side.
2.d.4. Connect the work cable to the workpiece as close as
possible to the area being welded.
2.d.5. Do not work next to welding power source.
1.h. To avoid scalding, do not remove the
radiator pressure cap when the engine is
hot.
!$ "$!"!%&! )$  %
Diesel engine exhaust and some of its constituents
are known to the State of California to cause can-
cer, birth defects, and other reproductive harm.
The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.
The Above For Diesel Engines The Above For Gasoline Engines
R

66
%&+
66
ARC RAYS an burn.
4.a. Use a shield with the proper filter and cover
plates to protect your eyes from sparks and
the rays of the arc when welding or observing
open arc welding. Headshield and filter lens
should conform to A SI Z87. I standards.
4.b. Use suitable clothing made from durable flame-resistant
material to protect your skin and that of your helpers from
the arc rays.
4.c. Protect other nearby personnel with suitable, non-flammable
screening and/or warn them not to watch the arc nor expose
themselves to the arc rays or to hot spatter or metal.
ELECTRIC SHOCK an
kill.
3.a. The electrode and work (or ground) circuits
are electrically “hot” when the welder is on.
Do not touch these “hot” parts with your bare
skin or wet clothing. Wear dry, hole-free
gloves to insulate hands.
3.b. Insulate yourself from work and ground using dry insulation.
Make certain the insulation is large enough to cover your full
area of physical contact with work and ground.
In addition to the normal safety pre autions, if welding
must be performed under ele tri ally hazardous
onditions (in damp lo ations or while wearing wet
lothing; on metal stru tures su h as floors, gratings or
s affolds; when in ramped positions su h as sitting,
kneeling or lying, if there is a high risk of unavoidable or
a idental onta t with the workpie e or ground) use
the following equipment:
• Semiautomati DC Constant Voltage (Wire) Welder.
• DC Manual (Sti k) Welder.
• AC Welder with Redu ed Voltage Control.
3.c. In semiautomatic or automatic wire welding, the electrode,
electrode reel, welding head, nozzle or semiautomatic
welding gun are also electrically “hot”.
3.d. Always be sure the work cable makes a good electrical
connection with the metal being welded. The connection
should be as close as possible to the area being welded.
3.e. Ground the work or metal to be welded to a good electrical
(earth) ground.
3.f.
Maintain the electrode holder, work clamp, welding cable and
welding machine in good, safe operating condition. Replace
damaged insulation.
3.g. ever dip the electrode in water for cooling.
3.h. ever simultaneously touch electrically “hot” parts of
electrode holders connected to two welders because voltage
between the two can be the total of the open circuit voltage
of both welders.
3.i. When working above floor level, use a safety belt to protect
yourself from a fall should you get a shock.
3.j. Also see Items 6.c. and 8.
FUMES AND GASES
an be dangerous.
5.a. Welding may produce fumes and gases
hazardous to health. Avoid breathing these
fumes and gases. When welding, keep
your head out of the fume. Use enough
ventilation and/or exhaust at the arc to keep
fumes and gases away from the breathing zone. When
welding with ele trodes whi h require spe ial
ventilation su h as stainless or hard fa ing (see
instru tions on ontainer or MSDS) or on lead or
admium plated steel and other metals or oatings
whi h produ e highly toxi fumes, keep exposure as
low as possible and within appli able OSHA PEL and
ACGIH TLV limits using lo al exhaust or me hani al
ventilation. In onfined spa es or in some ir um-
stan es, outdoors, a respirator may be required.
Additional pre autions are also required when welding
on galvanized steel.
5. b. The operation of welding fume control equipment is affected
by various factors including proper use and positioning of
the equipment, maintenance of the equipment and the spe-
cific welding procedure and application involved. Worker
exposure level should be checked upon installation and
periodically thereafter to be certain it is within applicable
OSHA PEL and ACGIH TLV limits.
5.c. Do not weld in locations near chlorinated hydrocarbon vapors
coming from degreasing, cleaning or spraying operations.
The heat and rays of the arc can react with solvent vapors to
form phosgene, a highly toxic gas, and other irritating prod-
ucts.
5.d. Shielding gases used for arc welding can displace air and
cause injury or death. Always use enough ventilation,
especially in confined areas, to insure breathing air is safe.
5.e. Read and understand the manufacturer’s instructions for this
equipment and the consumables to be used, including the
material safety data sheet (MSDS) and follow your
employer’s safety practices. MSDS forms are available from
your welding distributor or from the manufacturer.
5.f. Also see item 1.b.

666
%&+
666
FOR ELECTRICALLY
powered equipment.
8.a. Turn off input power using the disconnect
switch at the fuse box before working on
the equipment.
8.b. Install equipment in accordance with the U.S. ational
Electrical Code, all local codes and the manufacturer’s
recommendations.
8.c. Ground the equipment in accordance with the U.S. ational
Electrical Code and the manufacturer’s recommendations.
CYLINDER may explode
if damaged.
7.a. Use only compressed gas cylinders
containing the correct shielding gas for the
process used and properly operating
regulators designed for the gas and
pressure used. All hoses, fittings, etc. should be suitable for
the application and maintained in good condition.
7.b. Always keep cylinders in an upright position securely
chained to an undercarriage or fixed support.
7.c. Cylinders should be located:
• Away from areas where they may be struck or subjected to
physical damage.
• A safe distance from arc welding or cutting operations and
any other source of heat, sparks, or flame.
7.d. ever allow the electrode, electrode holder or any other
electrically “hot” parts to touch a cylinder.
7.e. Keep your head and face away from the cylinder valve outlet
when opening the cylinder valve.
7.f. Valve protection caps should always be in place and hand
tight except when the cylinder is in use or connected for
use.
7.g. Read and follow the instructions on compressed gas
cylinders, associated equipment, and CGA publication P-l,
“Precautions for Safe Handling of Compressed Gases in
Cylinders,” available from the Compressed Gas Association
1235 Jefferson Davis Highway, Arlington, VA 22202.
WELDING and CUTTING
SPARKS an
ause fire or explosion.
6.a. Remove fire hazards from the welding area.
If this is not possible, cover them to prevent
the welding sparks from starting a fire.
Remember that welding sparks and hot
materials from welding can easily go through small cracks
and openings to adjacent areas. Avoid welding near
hydraulic lines. Have a fire extinguisher readily available.
6.b. Where compressed gases are to be used at the job site,
special precautions should be used to prevent hazardous
situations. Refer to “Safety in Welding and Cutting” (A SI
Standard Z49.1) and the operating information for the
equipment being used.
6.c. When not welding, make certain no part of the electrode
circuit is touching the work or ground. Accidental contact
can cause overheating and create a fire hazard.
6.d. Do not heat, cut or weld tanks, drums or containers until the
proper steps have been taken to insure that such procedures
will not cause flammable or toxic vapors from substances
inside. They can cause an explosion even though they have
been “cleaned”. For information, purchase “Recommended
Safe Practices for the
Preparation for Welding and Cutting of
Containers and Piping That Have Held Hazardous
Substances”, AWS F4.1 from the American Welding Society
(see address above).
6.e. Vent hollow castings or containers before heating, cutting or
welding. They may explode.
6.f.
Sparks and spatter are thrown from the welding arc. Wear oil
free protective garments such as leather gloves, heavy shirt,
cuffless trousers, high shoes and a cap over your hair. Wear
ear plugs when welding out of position or in confined places.
Always wear safety glasses with side shields when in a
welding area.
6.g. Connect the work cable to the work as close to the welding
area as practical. Work cables connected to the building
framework or other locations away from the welding area
increase the possibility of the welding current passing
through lifting chains, crane cables or other alternate cir-
cuits. This can create fire hazards or overheat lifting chains
or cables until they fail.
6.h. Also see item 1.c.
6.I. Read and follow FPA 51B “ Standard for Fire Prevention
During Welding, Cutting and Other Hot Work”, available
from FPA, 1 Batterymarch Park, PO box 9101, Quincy, Ma
022690-9101.
6.j. Do not use a welding power source for pipe thawing.
Refer to http://www.lin olnele tri . om/safety for additional safety information.

6C
%&+
6C
"$I'&! %%Q$&I
Pour votre propre protection lire et observer toutes les instructions
et les précautions de sûreté specifiques qui parraissent dans ce
manuel aussi bien que les précautions de sûreté générales suiv-
antes:
%K?2AJ"<B?%<B1.42S?0
1. Protegez-vous contre la secousse électrique:
a. Les circuits à l’électrode et à la piéce sont sous tension
quand la machine à souder est en marche. Eviter toujours
tout contact entre les parties sous tension et la peau nue
ou les vétements mouillés. Porter des gants secs et sans
trous pour isoler les mains.
b. Faire trés attention de bien s’isoler de la masse quand on
soude dans des endroits humides, ou sur un plancher
metallique ou des grilles metalliques, principalement dans
les positions assis ou couché pour lesquelles une grande
partie du corps peut être en contact avec la masse.
c. Maintenir le porte-électrode, la pince de masse, le câble
de soudage et la machine à souder en bon et sûr état
defonctionnement.
d.Ne jamais plonger le porte-électrode dans l’eau pour le
refroidir.
e. Ne jamais toucher simultanément les parties sous tension
des porte-électrodes connectés à deux machines à souder
parce que la tension entre les deux pinces peut être le
total de la tension à vide des deux machines.
f. Si on utilise la machine à souder comme une source de
courant pour soudage semi-automatique, ces precautions
pour le porte-électrode s’applicuent aussi au pistolet de
soudage.
2. Dans le cas de travail au dessus du niveau du sol, se protéger
contre les chutes dans le cas ou on recoit un choc. Ne jamais
enrouler le câble-électrode autour de n’importe quelle partie
du corps.
3. Un coup d’arc peut être plus sévère qu’un coup de soliel,
donc:
a. Utiliser un bon masque avec un verre filtrant approprié
ainsi qu’un verre blanc afin de se protéger les yeux du ray-
onnement de l’arc et des projections quand on soude ou
quand on regarde l’arc.
b. Porter des vêtements convenables afin de protéger la
peau de soudeur et des aides contre le rayonnement de
l‘arc.
c. Protéger l’autre personnel travaillant à proximité au
soudage à l’aide d’écrans appropriés et non-inflammables.
4. Des gouttes de laitier en fusion sont émises de l’arc de
soudage. Se protéger avec des vêtements de protection libres
de l’huile, tels que les gants en cuir, chemise épaisse, pan-
talons sans revers, et chaussures montantes.
5. Toujours porter des lunettes de sécurité dans la zone de
soudage. Utiliser des lunettes avec écrans lateraux dans les
zones où l’on pique le laitier.
6. Eloigner les matériaux inflammables ou les recouvrir afin de
prévenir tout risque d’incendie dû aux étincelles.
7. Quand on ne soude pas, poser la pince à une endroit isolé de
la masse. Un court-circuit accidental peut provoquer un
échauffement et un risque d’incendie.
8. S’assurer que la masse est connectée le plus prés possible
de la zone de travail qu’il est pratique de le faire. Si on place
la masse sur la charpente de la construction ou d’autres
endroits éloignés de la zone de travail, on augmente le risque
de voir passer le courant de soudage par les chaines de lev-
age, câbles de grue, ou autres circuits. Cela peut provoquer
des risques d’incendie ou d’echauffement des chaines et des
câbles jusqu’à ce qu’ils se rompent.
9. Assurer une ventilation suffisante dans la zone de soudage.
Ceci est particuliérement important pour le soudage de tôles
galvanisées plombées, ou cadmiées ou tout autre métal qui
produit des fumeés toxiques.
10. Ne pas souder en présence de vapeurs de chlore provenant
d’opérations de dégraissage, nettoyage ou pistolage. La
chaleur ou les rayons de l’arc peuvent réagir avec les vapeurs
du solvant pour produire du phosgéne (gas fortement toxique)
ou autres produits irritants.
11. Pour obtenir de plus amples renseignements sur la sûreté,
voir le code “Code for safety in welding and cutting” CSA
Standard W 117.2-1974.
"$I'&! %%Q$&I"!'$
% %O%!'$O
&$ %!$&'$&O
$$%%'$
1. Relier à la terre le chassis du poste conformement au code de
l’électricité et aux recommendations du fabricant. Le dispositif
de montage ou la piece à souder doit être branché à une
bonne mise à la terre.
2. Autant que possible, I’installation et l’entretien du poste seront
effectués par un électricien qualifié.
3. Avant de faires des travaux à l’interieur de poste, la debranch-
er à l’interrupteur à la boite de fusibles.
4. Garder tous les couvercles et dispositifs de sûreté à leur
place.

CC
Thank You for selecting a #'&+ product by Lincoln Electric. We want you
to take pride in operating this Lincoln Electric Company product
••• as much pride as we have in bringing this product to you!
$2.1A56@!=2?.A<?@.;B.90<:=92A29F before attempting to use this equipment. Save this manual and keep it
handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.
The level of seriousness to be applied to each is explained below:
)$  
This statement appears where the information :B@A be followed 2E.0A9F to avoid @2?6<B@=2?@<;.96;7B?F or 9<@@<39632.
This statement appears where the information :B@A be followed to avoid :6;<?=2?@<;.96;7B?F or 1.:.42A<A56@2>B6=:2;A.
'&!
!;6;2 "?<1B0A $246@A?.A6<;
- Register your machine with Lincoln Electric either via fax or over the Internet.
• For faxing: Complete the form on the back of the warranty statement included in the literature packet
accompanying this machine and fax the form per the instructions printed on it.
• For On-Line Registration: Go to our
)R%&.ADDD96;0<9;2920A?600<:Choose “Quick Links” and then
“Product Registration”. Please complete the form and submit your registration.
'%&!$%%%& "!+
The business of The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equip-
ment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occasion, purchasers may ask Lincoln
Electric for advice or information about their use of our products. We respond to our customers based on the best information in our posses-
sion at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such infor-
mation or advice. We expressly disclaim any warranty of any kind, including any warranty of fitness for any customer’s particular purpose,
with respect to such information or advice. As a matter of practical consideration, we also cannot assume any responsibility for updating or
correcting any such information or advice once it has been given, nor does the provision of information or advice create, expand or alter any
warranty with respect to the sale of our products.
Lincoln Electric is a responsive manufacturer, but the selection and use of specific products sold by Lincoln Electric is solely within the control
of, and remains the sole responsibility of the customer. Many variables beyond the control of Lincoln Electric affect the results obtained in
applying these types of fabrication methods and service requirements.
Subject to Change – This information is accurate to the best of our knowledge at the time of printing. Please refer to www.lincolnelectric.com
for any updated information.
Please Examine Carton and Equipment For Damage Immediately
When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims
for material damaged in shipment must be made by the purchaser against the transportation company at the
time the shipment is received.
Please record your equipment identification information below for future reference. This information can be
found on your equipment nameplate or product carton label.
Model ame and Sales Spec umber (K-xxx) _____________________________________
Date of Purchase __________________________________
Whenever you request replacement parts for or information on this equipment always supply the information
you have recorded above.

Page
;@A.99.A6<; %20A6<;
%.32AF"?20.BA6<;@ 
Connector it Installation to Gun Cable.................................................................A-1
466-1.............................................................................................................A-1
466-2.............................................................................................................A-1
466-3.............................................................................................................A-1
466-4.............................................................................................................A-1
466-5 ......................................................................................................A-1,A-2
Liner Installation.....................................................................................................A-2
Contact Tip and Gas Nozzle Installation................................................................A-3
Connector to Feeder..............................................................................................A-3
Connection to Lincoln Feeders .......................................................................A-3
Connection to Adapter Feeders ......................................................................A-3
Connection to Miller feeders ...........................................................................A-3
Connection to Hobart feeders .........................................................................A-3
Connection to L-Tec feeders...........................................................................A-4
________________________________________________________________________________
!=2?.A6<; %20A6<;
%.32AF"?20.BA6<;@ 
General Description...............................................................................................B-1
Electrodes and Equipment.....................................................................................B-2
Making a Weld.......................................................................................................B-2
Avoid Wire Feeding Problems ...............................................................................B-2
________________________________________________________________________
.6;A2;.;02%20A6<;
Liner Removal .......................................................................................................D-1
Removal, Installation and Trimming Installations for 497 .............................D-1
Gun and Tube Nozzles..........................................................................................D-1
Gun Cables............................................................................................................D-1
Cable Cleaning ...............................................................................................D-1
Gun Tube End Repair .............................................................................D-1, D-2
Wire Feeder End Repair .................................................................................D-3
________________________________________________________________________
&?<B/92@5<<A6;4%20A6<;
Safety Precautions.................................................................................................E-1
How to Use Troubleshooting Guide.......................................................................E-1
Troubleshooting Guide ..........................................................................................E-2
________________________________________________________________________
".?A@".42@"%2?62@
------------------------------------------------------------------------
C6
C6 &!! & &%


 %&&! 
 'N 'N"$!'$(' %

! &!$& %&&!
&!' 
The MAGNUM® & MAGNUM® PRO CURVE 200
cable is shipped as a generic assembly and must be
assembled with either a 466-1, -2, -3, -4 or -5
Connector it.
;@A.99.A6<; (For Lincoln Feeders)
a. Remove brass cable connector and insulation tube
(see Figure A.1) from the 466-1 kit. Slide the insu-
lation tube onto the connector from the threaded
end and screw it onto the feeder end of the gun
cable. Tighten the connection with wrench provid-
ed.
b. Remove the molded gas plug fitting on the side of
the feeder end handle and replace it with the
barbed brass fitting provided in the kit. The included
wrench will fit both the gas plug and barbed fitting.
c. Attach the round connector of the gun control cable
provided to the trigger connector on the front of the
Lincoln feeder. !& Both the plug and socket are
keyed and must be properly oriented.
d. Place one tubing clamp onto each end of the flexi-
ble tubing provided, approximately 2 inch. (51 mm)
in from each end. Slide one end of the tubing onto
the barbed connector on the feeder end cable han-
dle (step b) and move the clamp down near the end
of the tube to assure a good gas seal.
!& An optional 481 MAGNUM® Fast-
Connect Gas Tube it is available to provide tool-
less gas tube connection to Lincoln wire feeders.
Install per the instructions sent with the kit.
$2.1A56@2;A6?26;@A.99.A6<;@20A6<;/23<?2F<B
@A.?A6;@A.99.A6<;
%&+"$'&! %
&$R%! can kill.
• Have an electrician install and ser-
vice this equipment.
• Turn the input power off at the fuse
box before working on equipment.
• Do not touch electrically hot parts.
• Be sure to discharge capacitors with
the procedure outlined in the
Maintenance Section of this manual
before working in that area of the
equipment.
---------------------------------------------------------------------
;@A.99.A6<; (For Adapted Feeders)
a. Remove brass connector (see Figure A-1) from the
466-2 kit and screw it onto the feeder end of the
gun cable. Tighten the connection with the wrench
provided.
b. Check that the molded gas plug fitting is sealing
the gas fitting hole in the side of the feeder end
handle.
;@A.99.A6<; (For Miller Feeders)
a. Remove brass cable connector (see Figure A.1)
from the 466-3 kit and screw it onto the feeder
end of the gun cable. Tighten the connection with
the wrench provided.
b. Check that the molded gas plug fitting is sealing
the gas fitting hole in the side of the feeder end
handle.
c. Attach the round connector or the gun control cable
provided to the trigger connector on the front of the
Miller feeder.
;@A.99.A6<; (For Hobart Feeders)
a. Remove brass cable connector (see Figure A.1)
from the 466-4 kit and screw it onto the feeder
end of the gun cable. Tighten the connection with
the wrench provided.
b. Remove the molded gas plug fitting on the side of
the feeder end handle and replace it with the
barbed brass fitting provided in the kit. The included
wrench will fit both the gas plug and barbed fitting.
c. Attach the phone plug connector of the gun control
cable provided to the trigger connector on the front
of the Hobart feeder.
d. Place one tubing clamp onto each end of the flexi-
ble tubing provided, approximately 2 inch. (51 mm)
in from each end. Slide one end of the tubing onto
the barbed connector on the feeder end cable han-
dle (Step b) and move the clamp down near the
end of the tube to assure a good gas seal.
;@A.99.A6<; (For L-Tec Feeders equipped
with an L-Tec feeder connector assembly)
a. Remove brass cable connector (see Figure A.1)
from the 466-5 kit and screw it onto the feeder
end of the gun cable. Tighten the connection with
the wrench provided.
b. Check that the molded gas plug fitting is sealing
the gas fitting hole in the side of the feeder end
handle.
)$  


 %&&! 
 'N 'N"$!'$(' %

c. For L-Tec machines that require lead connections
to made at a terminal strip located within the
machine (L-Tec 225), a gun control cable with
forked
terminals is provided . Connect the terminated
leads to the terminal strip. For a machine that
requires a twist-lock gun control cable connections,
continue
to use the L-Tec gun control cable provided
with the L-Tec wire feeder connector assembly.
Connect the
twist-lock plug to the proper receptacle
on the machine.
 $ %&&!
a. Lay the gun and cable straight on a flat surface.
b. Make sure that the set screw in the connector end
is backed out so as not to damage liner or liner
bushing.
c. Insert a new untrimmed liner into the connector
end
of the cable. Be sure the liner bushing is stencilled
appropriately for the wire size being used.
NOTE: For liners series KP44N and KP45N
B efore fully seating the liner bushing, it will be
necessary to trim the liner’s inner tube flush with
the liner
bushing using a sharp blade . After triming,
remove any burrs from inner tube and insure that
the opening is fully open.
d. Before installing the gas diffuser, fully seat the liner
bushing in the connector and:
For 466-1, 466-2, 466-5 and 2950 tighten the
set screw in the cable connector.
OR
For 466-3 and 466-4, screw in the connector
cap provided in the kit until it seats on the face of
the bushing. Then insert the appropriate piece of
liner material into the connector cap and tighten the
set screw. Three pieces of liner material are includ-
ed i
n these connector kits to help guide the electrode
through the connector cap. The piece with the
smallest inner diameter is designed for .045 inch,
(1.2 mm) maximum diameter electrode. The next
largest diameter is for 1/16 inch (1.6 mm maximum
diameter electrode. The largest diameter piece of
liner material is for 5/64 inch (2.0 mm) maximum
diameter electrode.
e. Be sure the cable is straight and then trim the liner
to the length shown in 64B?23<? or
64B?23<?. Remove any burrs from the
end of the liner.
f. Screw the gas diffuser onto the end of the gun tube
and tighten with the wrench provided.
g. Tighten the set screw in the side of the gas diffuser
against the cable liner using the Allen wren ch
provided. <A2%2A @0?2D 6@ ;<A 3<B;1 <;B;
.;1922;1<3
The screw should only e gently tightened.
Overtightening will split or collapse the liner and
cause poor wire feeding.
'$
'&!


 %&&! 
 'N 'N"$!'$(' %

! &&&" % !,, %&
&!
a. Choose the correct size contact tip for the elec-
trode being used (wire size is stenciled on the
side of the contact tip) and screw it snugly into the
gas diffuser.
b. Be
sure the nozzle insulator is fully screwed onto the
gas diffuser
and does not block the gas holes in the
diffuser.
c. Slip the appropriate gas nozzle onto the nozzle
insulator. Either a .62 inch (15.9 mm) or .50” (12.7 mm
I.D. slip-on gas nozzle may be used and should
be selected based on the welding application.
Choose the gas nozzle as appropriate for the
GMAW process to be used. Typically, the contact
tip end should be flush to .12 inch (3.1 mm)
extended for the short-circuiting transfer process
and .12 inch (3.1 mm) recessed for spray transfer.
For the Outershield (FCAW) process, 1/4 inch (6.3
mm) recess is recommended.
%&+"$'&! %
ELECTRIC SHOCK CAN KILL.
M<;<AA<B052920A?60.99F96C2=.?A@
@B05.@<BA=BAA2?:6;.9@<?6;A2?
;.9D6?6;4
---------------------------------------------------------------------
)$  
! &! &!$
Connection to Lincoln Feeders
Gun cable assemblies which were assembled with a
466-1 Connector it will connect easily to any
Lincoln LN-7, LN-8, LN-9, SP200 or LN-25 feeder.
a. Check that the drive roll(s) and feeder guide tubes
are appropriate for the electrode size being used.
b. Fully push the brass connector end of the gun
cable into the conductor block on the outgoing side
of the feeder wire drive. Secure the cable using the
hand screw or set screw in the conductor block.
c. Insert the control cable plug from the feeder trigger
circuit into the mating socket on the feeder end
cable handle (See 466-1
connector kit installation
to gun cable in this section
).
d. Slide the free end of the flexible hose onto the
barbed gas fitting on the front of the Lincoln feeder
(See 466-1 connector kit installation to gun cable in
this section) Move the corresponding tubing clamp
down near the end of the tube to assure a good
gas seal
9/16”(14.3mm)
LINERTRIM
LENGTH
GUNTUBEASSEMBLY
GUNHANDLE
COLLARASSEMBLYFEEDERENDCABLEHANDLE
SETSCREW
GASVENTEDHOLE
NOZZLEASSEMBLY
CONTACTTIP
DIFFUSER
LINERASSEMBLY(LINERBUSHINGTOBESEATED
TIGHTAGAINSTBRASSCABLECONNECTOR)INSULATOR
9 / 16” (14.3mm)
LINER TRIM
LENGTH
GUN TUBE ASSEMBLY
GUN HANDLE
COLLAR ASSEMBLY FEEDER END CABLE HANDLE
SET SCREW
GAS VENTED HOLE
NOZZLE ASSEMBLY
CONTACT TIP
DIFFUSER
LINER ASSEMBLY (LINER BUSHING TO BE SEATED
TIGHT AGAINST BRASS CABLE CONNECTOR) INSULATOR
'$


 %&&! 
 'N 'N"$!'$(' %

Connection to L-Tec Adapted Feeders
Gun cable assemblies which were assembled with a
466-5 Connector it will connect easily to an L-
Tec fe
eder equipped with an L-Tec feeder connector
assembly. L-Tec feeders require this connector
assembly (similar to a Tweco®adapter) to connect
with a gun and cable.
a. Check that the adapter and feeder outgoing guide,
as well as the drive roll, are appropriate for the
electrode size being used.
b. Fully push the brass connector end of the gun
cable into the brass adapter on the outgoing side of
the feeder wire drive. Secure the cable using the
hand screw, set screw or pin.
c. Insert the control cable plug from the feeder trigger
circuit into the mating socket on the gun cable con-
nector handle. For machines with a twist-lock trig-
ger lead receptacle, if the L-Tec gun control cable
does not easily connect with the socket, the gun
control cable that came with the 466-5 kit can be
used. To do this, cut off the gun control leads as
close to the forked terminals as possible and skin
back the leads 7/16 inch (11 mm). Remove the
twist-lock plug from the L-Tec control cable and
connect it to the 466-5 cable Make sure the outer
jacket of the connector is caught within the plug’s
strain relief.
Connection to Adapted Feeders
Gun cable assemblies which were assembled with a
466-2 Connector it will connect easily to any
prop
erly adapted feeder.
a. Check that the adapter and feeder outgoing guide,
as well as the drive roll, are appropriate for the
electrode size being used.
b. Fully push the brass connector end of the gun
cable into the brass adapter on the outgoing side of
the feeder wire drive. Secure the cable using the
hand screw or set screw in the adapter.
c. Insert the control cable plug from the feeder trigger
circuit into the mating socket on the gun cable con-
nector handle.
Connection to Miller Feeders
Gun and cable assemblies which were assembled
with a 466-3 Connector it will connect easily to a
variety of popular Miller wire feeders.
a. Check that the gun liner, connector cap liner, drive
rolls and guide tubes are appropriate for the elec-
trode
size being used. Three different diameter
pieces of liner material are included in each kit.
b. Fully push the brass connector end of the gun and
cable
into the connector receptacle on the outgoing
side of the feeder wire drive. Tighten the hand
screw to clamp down on the connector.
c. Insert the control cable plug from the feeder trigger
circuit into the mating socket on the gun cable con-
nector handle.
Connection to Ho art Feeders
Gun and cable assembles which were assembled with
a 466-4 Connector it will connect easily to a variety
of Hobart wire feeders.
a. Check that the gun liner, connector cap liner, drive
rolls and guide tubes are appropriate for the elec-
trode
size being used. These different diameter
pieces of liner material are included in each kit.
b. Fully push the brass connector end of the gun and
cable into connector receptacle on the outgoing
side of the feeder wire drive. Tighten the hand
screw to clamp down on the connector.
c. Insert the control cable plug from the feeder trigger
circuit
into the mating socket on the gun cable
connector handle.
d. Sl
ide the free end of the flexible hose (mounted to t he
gun in 466-4 Installation Section) onto
the gas f itting
on the
Hobart wire feeder. Move the corresponding
tubing clamp down near the end of the tube to
assure a good gas seal.

 'N 'N"$!'$(' %

!"$&!

$2.1.;1B;12?@A.;1A56@2;A6?2@20A6<;/23<?2
<=2?.A6;4F<B?:.056;2
%&+"$'&! %
&$%!0.;8699
• Do not touch electrically live parts such
as output terminals or internal wiring.
• Insulate yourself from the work and
ground.
• Always wear dry insulating gloves.
)$  
'% %%
0.;/21.;42?<B@
• eep your head out of fumes.
• Use ventilation or exhaust to
remove fumes from breathing
zone.
$$+%
0.;/B?;
• Wear eye, ear and body
protection.
) '&& .;1
!' %"$%
0.;0.B@236?2<?2E=9<@6<;
• eep flammable material away.
• Do
not weld, cut or gouge on contai ners
that have held combustibles.
Only qualified personnel should operate this equip-
ment. Observe all safety information throughout this
manual.
 $%$"&!
The MAGNUM® & MAGNUM® PRO CURVE 200
amp GMA gun and cable assembly has been
designed to meet NEMA specification EW3 for weld-
ing with steel electrode using the GMAW (gas metal
arc welding) and gas-shielded FCAW (flux-cored arc
welding) processes: See Table B.1 and Table B.2.
The 497 MAGNUM® & 2950 MAGNUM® PRO
CURVE gun is not factory equipped with a feeder
end connector. With the 466-1 MAGNUM®
Connector it, it can be used with any Lincoln LN-7,
LN-8, LN-9, SP200 or LN-25 semiautomatic wire
feeder. An optional 481 MAGNUM® Fast-Connect
Gas Tube it is available to provide tool-less gas tube
connection to Lincoln wire feeders. Non-GMA model
wire feeders require an optional gas solenoid valve.
The 497 gun can also be used with any wire feeder
equipped with a Tweco® # 1, 2, 3, 350 or 4 wire feed
adapter kit by using the 466-2 Adapted Feeder
Connector it.
A 466-3, Miller Feeder Connector it allows connec tion
of the MAGNUM® & MAGNUM® PRO CURVE to
popular Miller wire feeders.
A 466-4, Hobart Feeder Connector it allows con-
nection of the MAGNUM® & MAGNUM® PRO
CURVE to popular Hobart wire feeders.
A 466-5, L-Tec Feeder Connector it allows connec-
tion of the MAGNUM® & MAGNUM® PRO CURVE to
popular L-Tec wire feeders.
For best results when welding mild and alloy steels, it
is recommended that Lincoln solid wire electrodes be
used for the GMAW process and OS71 Lincoln
Outershield®cored electrodes for the gas-shielded
FCAW process.
2@0?6=A6<; B; <;A.0A
./92 &6=@ .@
"?<1B0A 2;4A5 )6?2%6G2 %A.;1.?1 633B@2? .@ ./92 B;&B/2
B:/2? : 6;:: BAF @@2:/9F <GG92 ;@B9.A<? 6;2? L
497-3 15 ft. .025 (0.6) P14-25 P52-23 P22-50 P32 P42-25-15 P2028-1
(4.5) .030 (0.8) -30
497-2 10 ft. .035 (0.9) P14-35 P52 P22-50 P32 P42-4045-15 P2028-1
(3.0) .045 (1.2) -45
497-6 12 ft. .035 (0.9) P14-35 P52 P22-50 P32 P42-4045-15 P2028-1
(3.6) .045 (1.2) -45
497-1 15 ft. .035 (0.9) P14-35 P52 P22-50 P32 P42-4045-15 P2028-1
(4.5) .045 (1.2) -45
 'N
"%&'&++)&!%
"%&'&++)&*%
&


!"$&!

&$!% #'" &
The MAGNUM® & MAGNUM® PRO CURVE 200 gun
and cable has been designed for use with Lincoln L-
50 and Super Arc L-56, solid steel wire electrodes for
the GMAW process and Lincoln Outershield® cored
electrodes for the gas-shielded FCAW process. Refer
to the appropriate Lincoln Process and Procedure
Guidelines for the electrode used for information on
recommended electrical and visible stickouts.
 )
a. Check that the welding power source is on and that
the shielding gas supply is set for the proper flow
rate.
b. Position electrode over joint. End of the electrode
should be slightly off the work.
c. Lower welding helmet, close gun trigger and begin
welding. Hold the gun so the contact tip to work
distance gives the correct electrical stickout as
required for the procedure being used.
d. To stop welding, release the gun trigger and then
pull the gun away from the work after the arc goes
out. Follow wire feeder instruction manual if using a
trigger interlock circuit.
(! )$ "$!%
Wire feeding problems can be avoided by observing
the following gun handling procedures:
a. Do not kink or pull cable around sharp corners.
b. eep the electrode cable as straight as possible
when welding or loading electrode through cable.
c. Do not allow dolly wheels or trucks to run over
cables.
d. eep cable clean by following maintenance instruc-
tions.
e. Use only clean, rust-free electrode. The Lincoln
electrodes have proper surface lubrication.
f. Replace contact tip when the arc starts to become
unstable or the contact tip end is fused or
deformed.
 'N 'N"$!'$(' %
** Feeder its installed on the gun at the factory.
2@0?6=A6<; B; <;A.0A&6=@.@
"?<1B0A ./92)6?2%6G22.CF 633B@2? .@ ./92 B;&B/2 2212?
B:/2? 2;4A5:6;::BAF @@2:/9F <GG92  %'&!$6;2? L &F=2
15 ft. .035 (0.9) P2744-035 Lincoln “10 Series”
2950-2-10-45 (4.5) .045 (1.2) P2744-045 P2746-1 P2742-1-62R P2773-2 P44-3545-15 P2924-60 466-10
2950-2 15 ft. .045 (1.2) P2744-045 P2746-1 P2742-1-62R P2773-2 P2924-60
(4.5)
 'N"$!'$(
"%&'&++)&!%
"%&'&++)&*%
&


 &  

 'N 'N"$!'$(' %
Excessive pressure at the start may cause the dirt
to form a plug.
Flex the cable over its entire length and again blow
out the cable. Repeat this procedure until no further
dirt comes out.
./92 92.;6;4
The MAGNUM® & MAGNUM® PRO CURVE 200 gun
features the use of repairable cable connectors. If the
cable ever gets severely damaged, it may be cut
shorter and repaired by the user. Repair cables as fol-
lows:
B;&B/2;1$2=.6?(Requires 2 S19492-2
Terminals)
a. Remove the cable liner per Removal, Installation
and Trimming Instructions on page D-1.
b. Remove the gun tube per Gun Tubes and Nozzles
in this section.
c. Remove three #6 screws from the gun handle, sep-
arate the two halves, and remove the cable from
the handle along with the trigger assembly.
d. Remove gun tube connector from cable by
unscr
ewing connector nut from gun tube connector.
If the cable inner tube is difficult to remove from the
connector assembly, carefully slit it lengthwise with
a knife up to the brass connector.
e. Uncouple the strain relief by pushing its outer
housing toward the middle of the cable. Move the
strain relief and the cable boot toward the middle of
the cable, past the damaged section.
f. Cut off the damaged section of cable and strip off
the outer jacket as shown in Figure D.1. Be careful
not to cut the insulation on the control wires while
stripping jacket. Strip the red and white control
leads 1/4 inch (6.4mm) from the end and crimp a
new S19492-2 terminal to each lead.
 $$!( $" &
!&: The variation in cable lengths prevents the inter-
changeability of liners. Once a liner has been cut for a partic-
ular gun, it should not be installed in another gun, unless it
can meet the liner cut off length requirement. Liners are
shipped with the jacket of the liner extended the proper
amount.
Removal, Installation and Trimming Instruction for K497
& K2950 (with K466 Connector Kit installed)
a. For gun and cables using a 466-1, 466-2 or 466-5
connector kit, locate and loosen two set screws which are
used to hold the old liner in place with a 5/64 inch (2.0
mm) Allen wrench (provided with the connector kit). One
set screw is located in the connector at the wire feeder
end. The gas nozzle and nozzle insulator must be
removed to gain access to the second set screw which is
located in the gas diffuser. <A2 Set screw is not
found on 2950.
b. For gun and cables using a 466-3 or 466-4 connector
kit, remove the connector cap with the wrench provided in
the kit. Loosen the set screw located the gas diffuser with
the Allen wrench provided in the connector kit. The gas
nozzle and nozzle insulator must be removed to gain
access to the diffuser.
c. Remove the gas diffuser from the gun tube.
d. Lay the gun cable on a flat surface with the cable straight
and pull the liner out of the cable from the cable connec-
tor end.
e. Install the new liner per Liner Installation Section.
' &'%  !,,%
a. Replace worn contact tips as required.
b. Remove spatter from inside of gas nozzle and from tip
after each 10 minutes of arc time or as required.
c. To remove gun tube from gun, loosen socket-head
clamping screw in handle with 3/16 inch (4.8 mm) Allen
wrench. Remove gas nozzle and nozzle insulator and
also loosen small set screw in the diffuser using 5/64 inch
(2.0 mm) Allen wrench. %2A%0?2D;<A3<B;1<;
!&Small set screw in the diffuser :B@A be loosened,
otherwise liner could be damaged when attempting to
remove gun tube.
Pull gun tube out from gun handle. To reinstall, insert the
gun tube, push in as far as possible and retighten screws.
' %
./92 92.;6;4
Clean cable liner after using approximately 300 pounds (136
kg) of electrode. Remove the cable from the wire feeder and
lay it out straight on the floor. Remove the contact tip from
the gun. Using an air hose and only partial pressure, gently
blow out the cable liner from the gas diffuser end.
'&!
'$


 &  

NOTE: The cable contains three control leads. Any
two control leads can be used, provided the two color
used are the same at both ends. The extra lead is a
spare that can be used if one of the other leads
breaks
g. Check that the cable boot and both halves of the
strain relief are on the cable. Slip the connector nut
over the copper strands with the thread end out.
Orient gun tube connector so machined flat is on
the same side of the cable as the red and white
control leads. Assemble gun tube connector to
cable by forcing the steel tube of the connector
into the inside diameter of the cable inner tube
until the copper strands are butted against the gun
tube connector shoulder. eeping the copper
strands against the shoulder, pull the connector
nut over the copper strands, engage the gun tube
c
onnector threads, and tighten in place . Figure D.2.
NOTE: For best results, insert a .175/.197 inch (4.5-
5.0 mm) diameter rod through the connector and into
core of cable approximately 5.00 inch (127 mm) when
pushing the connector tube into the cable core tube.
To tighten, hold the connector in place while turning
the nut, and remove the rod from the core, The proce-
dure ensures the inner core does not kink while
assembling or tightening.
h. Pull the cut-off lead terminals off the trigger
assemble and connect the replacement control
lead terminals.
i. Position the cable boot and strain relief on the
cable so it fits in cable handle cavity and lock the
strain relief in place by pushing the two halves
together.
j. Assemble cable in left side of gun handle.
Assemble trigger into the proper handle cavity and
connect the control leads. Assemble right side of
gun handle and tighten the three screws that hold
the handle together. Refer to Figure D.3.
k. Install gun tube per Gun Tubes and Nozzles
Section.
l. Install and trim liner per Liner Installation Section.
 'N 'N"$!'$(' %
'$
'$

f. Check that the cable boot and cable handle are on
the cable. Slip the connector nut over the copper
strands with the threaded end out. Assemble
incoming connector to cable by forcing the steel
tube of the connector into the inside diameter of
the cable inner tube tube until the copper strands
are butted against the incoming connector shoul-
der. e
eping the copper strands against the shoulder,
pull the connector nut over the copper strands,
engage the incoming connector threads, and tight-
en in place. Refer to Figure D.2.
NOTE: For best results, insert a .175/.197 inch (4.5-
5.0 mm) diameter rod through the connector and into
core of cable approximately 5.00” (127 mm) when
pushing the connector tube into the cable core tube.
To tighten, hold the connector in place while turning
the nut, and remove the rod from the core. This proce-
dure ensures the inner core does not kink while
assembling or tightening.
g. Position cable boot and cable handle on cable and
assemble replacement control wire terminals in
place on the cable handle. Insert connector cover
in place. Install tailpiece and fasten to cable handle
with cable handle nut. Refer Figure D.4.
h. Replace the molded gas plug (or barbed fitting)
and feeder end connector.
i. Install and trim liner per Liner Installation in this
section.

 &  

Wire Feeder End Repair (Requires 2 S19492-1
Terminals)
a. Remove the cable liner per Removal, Installation,
and Trimming Instructions in this section.
b. Remove the feeder end connector, molded gas
plug (or barbed fitting), cable handle nut, plastic
tailpiece and connector cover (see Figure D.4).
NOTE: In order to remove the cable handle nut, the
tail of the connector cover must be depressed and
the cable handle nut rotated 1/4 inch turn counter-
clockwise as viewed from the feeder end.
c. Remove incoming connector from cable by
unscrewing connector nut from incoming connec-
tor. If the cable inner tube is difficult to remove from
the connector assembly, carefully slit it lengthwise
with a knife up to the brass connector.
d. Move the cable boot and cable handle toward the
middle of the cable past the damaged section.
e. Cut off the damaged section of cable and strip off
the outer jacket as shown in Figure D.1. Be careful
not to cut the insulation on the control wires while
stripping jacket. Strip the red and white control
leads 1/4 inch (6.4 mm) from the end and crimp a
new S19492-1 terminal to each lead.
NOTE: The cable contains three control leads. Any
two control leads can be used, provided the two colors
used are the same at both ends. The extra lead is a
spare that can be used if one of the other leads
breaks.
 'N 'N"$!'$(' %
)$  
'$
ELECTRIC SHOCK CAN KILL.
• Do not touch electrically live parts
such as output terminals or internal
wiring.


&$!'%!!& 

 'N 'N"$!'$(' %
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your
<0.96;0<9;BA5<?6G216291%2?C602.0696AF for technical troubleshooting assistance before you proceed.
'&!
This Troubleshooting Guide is provided to help you
locate and repair possible machine malfunctions.
Simply follow the three-step procedure listed below.
Step 1. LOCATE PROBLEM (SYMPTOM).
Look under the column labeled “PROBLEM (SYMP-
TOMS)”. This column describes possible symptoms
that the machine may exhibit. Find the listing that
best describes the symptom that the machine is
exhibiting.
Step 2. POSSIBLE CAUSE.
The second column labeled “POSSIBLE CAUSE” lists
the obvious external possibilities that may contribute
to the machine symptom.
Step 3. RECOMMENDED COURSE OF ACTION
This column provides a course of action for the
Possible Cause, generally it states to contact your
local Lincoln Authorized Field Service Facility.
If you do not understand or are unable to perform the
Recommended Course of Action safely, contact your
local Lincoln Authorized Field Service Facility.
!)&!'%&$!'%!!& '
Service and Repair should only be performed by Lincoln Electric Factory Trained Personnel.
Unauthorized repairs performed on this equipment may result in danger to the technician and
machine operator and will invalidate your factory warranty. For your safety and to avoid Electrical
Shock, please observe all safety notes and precautions detailed throughout this manual.
__________________________________________________________________________
)$  


&$!'%!!& 

 'N 'N"$!'$(' %
!/@2?C2.99%.32AFB61296;2@12A.6921A5?<B45<BAA56@:.;B.9
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your
<0.96;0<9;BA5<?6G216291%2?C602.0696AF for technical troubleshooting assistance before you proceed.
'&!
"$!%
%+"&!%
"!%%
'%
$! 
!'$%!&!
Drive rolls turn, but wire will not feed of
wire feeding is rough
Variable or “hunting” arc
Poor arc striking with sticking or “blast-off”,
weld porosity, narrow and ropy looking
bead, or electrode stubbing into plate
while welding
Tip seizes in diffuser
1. Gun cable kinked and/or twisted.
eep as straight as possible. Inspect
cable and replace if necessary.
2. Wire jammed in gun and cable.
Remove wire from gun and cable
— feed in new wire. Note any obstruc-
tion. Replace liner if necessary
3. Incorrect drive rolls and guide tubes.
Be sure the wire diameter being used is
stamped on drive rolls and guide tubes.
Replace if necessary
4. Gun cable liner dirty.
Clean liner or replace.
5. Worn drive rolls.
Replace or reverse split drive roll type.
6. Electrode rusty and/or dirty.
Replace or electrode if it is rusty.
7. Worn or improper size cable liner.
Replace cable liner.
8. Partially flashed, melted or improper
size contact tip. Replace the contact tip.
1. Contact tip worn or incorrect size.
Replace contact tip.
2. Worn or undersize ground cables or
poor ground connections.
Inspect — repair or replace as neces
sary.
3. Loose electrode connections.
Be sure the following connections are
tight: electrode cable to wire feeder and
power source, work cable to power
source and work, gun cable to wire
feeder contact tip to nozzle.
1. Improper procedures or techniques.
See “Gas Metal Arc Welding Guide”
(GS-100)
Improper gas shielding.
Clean gas cone. Make certain that gas
diffuser is not restricted. Make certain
that gas cylinder is not empty or turned
off. Make certain gas solenoid valve is
operating and gas flow rate is proper.
Remove gun liner and check rubber
seal for any sign of deterioration or
damage. Be sure set screw in brass
connector is in place and tightened
against the liner bushing.
1. Tip overheating due to prolonged or
excessive high current and/or duly
cycle welding.
Do not exceed current and duly cycle
rating of gun.
A light application of high temperature
antiseize lubricant (such as Lincoln
E2607 Graphic Grease) may be applied
to tip threads.
If all recommended possible areas
of misadjustment have been
checked and the problem persists,
<;A.0A F<B? 9<0.9 6;0<9;
BA5<?6G216291%2?C602.0696AF

READ AND UNDERSTAND THE MANUFACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE
USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL FABRICANTE PARA EL USO DE ESTE EQUIPO Y LOS
CONSUMIBLES QUE VA A UTILI AR, SIGA LAS MEDIDAS DE SEGURIDAD DE SU SUPERVISOR.
LISE ET COMPRENE LES INSTRUCTIONS DU FABRICANT EN CE QUI REGARDE CET EQUIPMENT ET LES PRODUITS A
ETRE EMPLOYES ET SUIVE LES PROCEDURES DE SECURITE DE VOTRE EMPLOYEUR.
LESEN SIE UND BEFOLGEN SIE DIE BETRIEBSANLEITUNG DER ANLAGE UND DEN ELEKTRODENEINSAT DES HER-
STELLERS. DIE UNFALLVERHÜTUNGSVORSCHRIFTEN DES ARBEITGEBERS SIND EBENFALLS U BEACHTEN.
)$  
(%!
"$'!
&& &!
)$ ' 
& HP!
%=.;6@5
?2;05
2?:.;
"<?AB4B2@2
.=.;2@2
56;2@2
<?2.;
?./60
lDo not touch electrically live parts or
electrode with skin or wet clothing.
lInsulate yourself from work and
ground.
lNo toque las partes o los electrodos
bajo carga con la piel o ropa moja-
da.
lAislese del trabajo y de la tierra.
lNe laissez ni la peau ni des vête-
ments mouillés entrer en contact
avec des pièces sous tension.
lIsolez-vous du travail et de la terre.
lBerühren Sie keine stromführenden
Teile oder Elektroden mit Ihrem
Körper oder feuchter Kleidung!
lIsolieren Sie sich von den
Elektroden und dem Erdboden!
lNão toque partes elétricas e elec-
trodos com a pele ou roupa molha-
da.
lIsole-se da peça e terra.
lKeep flammable materials away.
lMantenga el material combustible
fuera del área de trabajo.
lGardez à l’écart de tout matériel
inflammable.
lEntfernen Sie brennbarres Material!
lMantenha inflamáveis bem guarda-
dos.
lWear eye, ear and body protection.
lProtéjase los ojos, los oídos y el
cuerpo.
lProtégez vos yeux, vos oreilles et
votre corps.
lTragen Sie Augen-, Ohren- und Kör-
perschutz!
lUse proteção para a vista, ouvido e
corpo.

LEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE PARA ESTE EQUIPAMENTO E AS PARTES DE USO, E SIGA AS
PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
)$  
(%!
"$'!
&& &!
)$ ' 
& HP!
%=.;6@5
?2;05
2?:.;
"<?AB4B2@2
.=.;2@2
56;2@2
<?2.;
?./60
lKeep your head out of fumes.
lUse ventilation or exhaust to
remove fumes from breathing zone.
lLos humos fuera de la zona de res-
piración.
lMantenga la cabeza fuera de los
humos. Utilice ventilación o
aspiración para gases.
lGardez la tête à l’écart des fumées.
lUtilisez un ventilateur ou un aspira-
teur pour ôter les fumées des zones
de travail.
lVermeiden Sie das Einatmen von
Schweibrauch!
lSorgen Sie für gute Be- und
Entlüftung des Arbeitsplatzes!
lMantenha seu rosto da fumaça.
lUse ventilação e exhaustão para
remover fumo da zona respiratória.
lTurn power off before servicing.
lDesconectar el cable de ali-
mentación de poder de la máquina
antes de iniciar cualquier servicio.
lDébranchez le courant avant l’entre-
tien.
lStrom vor Wartungsarbeiten
abschalten! (Netzstrom völlig öff-
nen; Maschine anhalten!)
lNão opere com as tampas removidas.
lDesligue a corrente antes de fazer
serviço.
lNão toque as partes elétricas nuas.
lDo not operate with panel open or
guards off.
lNo operar con panel abierto o
guardas quitadas.
lN’opérez pas avec les panneaux
ouverts ou avec les dispositifs de
protection enlevés.
lAnlage nie ohne Schutzgehäuse
oder Innenschutzverkleidung in
Betrieb setzen!
lMantenha-se afastado das partes
moventes.
lNão opere com os paineis abertos
ou guardas removidas.