Lincoln Electric WELDLINE WTT2 20W User manual

EN
www.weldline.eu
LINCOLN ELECTRIC EUROPE S.L.
c/o Balmes, 89 - 8o2a- 08008 Barcelona - SPAIN
WTT2 20W 18W
Curent Duty cycle 60% 250 A 350 A
Duty cycle 100% 200 A 320 A
Light alloy welding, reduce the duty cycle about 30%
Water flow mini 1.0 l/mn
Water pressure 3.3 bars
Maxi temperature inlet water 45°C
Voltage class L - 113 V
Gas flow Mini : 7 l/mn - Maxi : 13 l/mn
Using electrodes Ø 1.0 / 3.2 mm Ø 1.0 / 4.0 mm
Origin
equipment fitted
to the torch
Back Cap Long Long
Long Long
Nozzle Ø 12 mm Ø 12 mm
Electrode Ø 2.4 L Ø 2.4 L
WTT2 4 m 8 m
20W
RL S W000278893 W000278906
RL S
18W
RL S W000278897 W000278900
20W
RL C5B W000278894 W000278905
RL C5B
18W
RL C5B W000278898 W000278899
N°8695-1196_Rev2_05/2018
We thank you for your trust in our company by purchasing this equipment which will provide
you with complete satisfaction if you comply with its conditions for use and maintenance.
CAUTION: The company declines all responsibility in case of modification, addition of
components or subassemblies, or any transformation of the equipment carried out by
the customer or a thirdparty,without prior specific written agreement from the company.
Arc welding and plasma cutting may be dangerous for the operator and persons close
to the work area. Read the operating manual and safety instructions W000261712.
See www.weldline.eu.
A) Maintenance / Troubleshooting
Before any internal verifications and repair work, make sure that the equipment is separated
from the electric installation by electrical isolation (by electrical isolation is meant a group of
operations designed to separate and keep the equipment de-energized).
At least every six months, you must check the proper condition of the insulation and
connections of the electric equipment and accessories such as plugs, flexible wires, ducts,
connectors, extension leads, partholders, electrode-holders, or torches...
Maintenance and repair work on the jackets and insulating ducts must be carried out
extremely carefully.
Have defective parts repaired by a specialist, or better still, have them replaced.
Routinely check the proper tightening and cleanliness of the electric connections.
B) Work-station
Use only electrode holders and torches which are perfectly insulated.
The operator must be insulated from the ground-surface and the workpiece (gloves, safety
shoes, dry clothes, leather apron, and so forth...).
Do not touch the electrode wire and the part (or the nozzle) simultaneously.
C) Protection
It is absolutely essential that your protect your eyes from blinding glare (glare of arc invisible
light and infrared and ultraviolet radiation).
The welding mask, without or with helmet, must always be equipped with a protective filter
whose gradation depends on the welding arc current intensity (EN 169 Standard).
Fumes emitted during welding operations may be dangerous. Use adequate protection
means (fumes extraction, ventiled masks...)
Technical data
TIG manual torch with natural cooling
Safety instructions
French lever rangeErgonomic Range
WTT2 4 m 8 m
20W EB S W000278891 W000278911
EB S
18W EB S W000278895 W000278902
20W
EB C5B W000278892 W000278909
EB C5B
18W
EB C5B W000278896 W000278901
20W EB S/
C5B FLEX W000382786 W000382787
18W EB S/
C5B FLEX W000382788 W000382789
WTT2 20W
WTT2 18W
Instructions for safety, use and maintenance
EN
www.weldline.eu
LINCOLN ELECTRIC EUROPE S.L.
c/o Balmes, 89 - 8o2a- 08008 Barcelona - SPAIN
WTT2 20W 18W
Curent Duty cycle 60% 250 A 350 A
Duty cycle 100% 200 A 320 A
Light alloy welding, reduce the duty cycle about 30%
Water flow mini 1.0 l/mn
Water pressure 3.3 bars
Maxi temperature inlet water 45°C
Voltage class L - 113 V
Gas flow Mini : 7 l/mn - Maxi : 13 l/mn
Using electrodes Ø 1.0 / 3.2 mm Ø 1.0 / 4.0 mm
Origin
equipment fitted
to the torch
Back Cap Long Long
Long Long
Nozzle Ø 12 mm Ø 12 mm
Electrode Ø 2.4 L Ø 2.4 L
WTT2 4 m 8 m
20W
RL S W000278893 W000278906
RL S
18W
RL S W000278897 W000278900
20W
RL C5B W000278894 W000278905
RL C5B
18W
RL C5B W000278898 W000278899
N°8695-1196_Rev2_05/2018
We thank you for your trust in our company by purchasing this equipment which will provide
you with complete satisfaction if you comply with its conditions for use and maintenance.
CAUTION: The company declines all responsibility in case of modification, addition of
components or subassemblies, or any transformation of the equipment carried out by
the customer or a thirdparty,without prior specific written agreement from the company.
Arc welding and plasma cutting may be dangerous for the operator and persons close
to the work area. Read the operating manual and safety instructions W000261712.
See www.weldline.eu.
A) Maintenance / Troubleshooting
Before any internal verifications and repair work, make sure that the equipment is separated
from the electric installation by electrical isolation (by electrical isolation is meant a group of
operations designed to separate and keep the equipment de-energized).
At least every six months, you must check the proper condition of the insulation and
connections of the electric equipment and accessories such as plugs, flexible wires, ducts,
connectors, extension leads, partholders, electrode-holders, or torches...
Maintenance and repair work on the jackets and insulating ducts must be carried out
extremely carefully.
Have defective parts repaired by a specialist, or better still, have them replaced.
Routinely check the proper tightening and cleanliness of the electric connections.
B) Work-station
Use only electrode holders and torches which are perfectly insulated.
The operator must be insulated from the ground-surface and the workpiece (gloves, safety
shoes, dry clothes, leather apron, and so forth...).
Do not touch the electrode wire and the part (or the nozzle) simultaneously.
C) Protection
It is absolutely essential that your protect your eyes from blinding glare (glare of arc invisible
light and infrared and ultraviolet radiation).
The welding mask, without or with helmet, must always be equipped with a protective filter
whose gradation depends on the welding arc current intensity (EN 169 Standard).
Fumes emitted during welding operations may be dangerous. Use adequate protection
means (fumes extraction, ventiled masks...)
Technical data
TIG manual torch with natural cooling
Safety instructions
French lever rangeErgonomic Range
WTT2 4 m 8 m
20W EB S W000278891 W000278911
EB S
18W EB S W000278895 W000278902
20W
EB C5B W000278892 W000278909
EB C5B
18W
EB C5B W000278896 W000278901
20W EB S/
C5B FLEX W000382786 W000382787
18W EB S/
C5B FLEX W000382788 W000382789
WTT2 20W
WTT2 18W
Instructions for safety, use and maintenance
EN

EN
www.weldline.eu
LINCOLN ELECTRIC EUROPE S.L.
c/o Balmes, 89 - 8o2a- 08008 Barcelona - SPAIN
WTT2 20W 18W
Curent Duty cycle 60% 250 A 350 A
Duty cycle 100% 200 A 320 A
Light alloy welding, reduce the duty cycle about 30%
Water flow mini 1.0 l/mn
Water pressure 3.3 bars
Maxi temperature inlet water 45°C
Voltage class L - 113 V
Gas flow Mini : 7 l/mn - Maxi : 13 l/mn
Using electrodes Ø 1.0 / 3.2 mm Ø 1.0 / 4.0 mm
Origin
equipment fitted
to the torch
Back Cap Long Long
Long Long
Nozzle Ø 12 mm Ø 12 mm
Electrode Ø 2.4 L Ø 2.4 L
WTT2 4 m 8 m
20W
RL S W000278893 W000278906
RL S
18W
RL S W000278897 W000278900
20W
RL C5B W000278894 W000278905
RL C5B
18W
RL C5B W000278898 W000278899
N°8695-1196_Rev2_05/2018
We thank you for your trust in our company by purchasing this equipment which will provide
you with complete satisfaction if you comply with its conditions for use and maintenance.
CAUTION: The company declines all responsibility in case of modification, addition of
components or subassemblies, or any transformation of the equipment carried out by
the customer or a thirdparty,without prior specific written agreement from the company.
Arc welding and plasma cutting may be dangerous for the operator and persons close
to the work area. Read the operating manual and safety instructions W000261712.
See www.weldline.eu.
A) Maintenance / Troubleshooting
Before any internal verifications and repair work, make sure that the equipment is separated
from the electric installation by electrical isolation (by electrical isolation is meant a group of
operations designed to separate and keep the equipment de-energized).
At least every six months, you must check the proper condition of the insulation and
connections of the electric equipment and accessories such as plugs, flexible wires, ducts,
connectors, extension leads, partholders, electrode-holders, or torches...
Maintenance and repair work on the jackets and insulating ducts must be carried out
extremely carefully.
Have defective parts repaired by a specialist, or better still, have them replaced.
Routinely check the proper tightening and cleanliness of the electric connections.
B) Work-station
Use only electrode holders and torches which are perfectly insulated.
The operator must be insulated from the ground-surface and the workpiece (gloves, safety
shoes, dry clothes, leather apron, and so forth...).
Do not touch the electrode wire and the part (or the nozzle) simultaneously.
C) Protection
It is absolutely essential that your protect your eyes from blinding glare (glare of arc invisible
light and infrared and ultraviolet radiation).
The welding mask, without or with helmet, must always be equipped with a protective filter
whose gradation depends on the welding arc current intensity (EN 169 Standard).
Fumes emitted during welding operations may be dangerous. Use adequate protection
means (fumes extraction, ventiled masks...)
Technical data
TIG manual torch with natural cooling
Safety instructions
French lever rangeErgonomic Range
WTT2 4 m 8 m
20W EB S W000278891 W000278911
EB S
18W EB S W000278895 W000278902
20W
EB C5B W000278892 W000278909
EB C5B
18W
EB C5B W000278896 W000278901
20W EB S/
C5B FLEX W000382786 W000382787
18W EB S/
C5B FLEX W000382788 W000382789
WTT2 20W
WTT2 18W
Instructions for safety, use and maintenance
EN
www.weldline.eu
LINCOLN ELECTRIC EUROPE S.L.
c/o Balmes, 89 - 8o2a- 08008 Barcelona - SPAIN
Kit B
W000279241
Kit L
W000279245
1 4
23
1
4
3
5
6L
6
7
8
L
L
9
2
9L
REP WTT2
20W
WTT2
18W Ø Wear parts
6L
W000306456 / 4.8
Long Nozzle
W000306457 W000306462 6.4
W000306458 W000306463 8.0
W000306459 W000306464 9.6
/ W000306465 11.2
7 / W000306466 // Gas Lens sealing ring
8
W000306385 W000306389 1.0
Gas Lens
collet body
W000306386 W000306390 1.6
W000306460 / 2.0
W000306387 W000306391 2.4
W000306388 W000306392 3.2
/ W000306393 4.0
9
W000306429 W000306434 6.4
Gas Lens nozzle
/ W000306435 8.0
W000306431 W000306436 9.6
W000306432 W000306437 11.2
W000306433 W000306438 12.8
W000306438 16.0
9L
/ W000306467 8.0
Long Gas Lens
nozzle
/ W000306468 9.6
/ W000306469 11.2
/ W000306470 12.8
REP WTT2
20W
WTT2
18W Ø Wear parts
1
W000306398 W000306399 // Short back cap
W000306400 / // Medium back cap
W000306402 W000306403 // Long back cap
2 W000306404 W000306405 // Back cap
3 W000306396 W000306397 // Sealing ring
4
W000306406 W000306411 1.0
Collet
W000306407 W000306412 1.6
W000306408 W000306413 2.0
W000306409 W000306414 2.4
W000306410 W000306415 3.2
/ W000306416 4.0
5
W000306376 W000306380 1.0
Collet body
W000306377 W000306381 1.6
W000306378 W000270781 2.0
W000306455 W000306382 2.4
W000306379 W000306383 3.2
/ W000306384 4.0
6
W000306417 W000306423 6.4
Nozzle
W000306418 W000306424 8.0
W000306419 W000306425 9.6
W000306420 W000306426 11.2
W000306421 W000306427 12.8
W000306422 W000306428 16.0
/ W000306461 19.2
Trigger simple commands
Simplified maintenance.
Wear parts
Gas connector change
EN

EN
www.weldline.eu
LINCOLN ELECTRIC EUROPE S.L.
c/o Balmes, 89 - 8o2a- 08008 Barcelona - SPAIN
WTT2 20W 18W
Curent Duty cycle 60% 250 A 350 A
Duty cycle 100% 200 A 320 A
Light alloy welding, reduce the duty cycle about 30%
Water flow mini 1.0 l/mn
Water pressure 3.3 bars
Maxi temperature inlet water 45°C
Voltage class L - 113 V
Gas flow Mini : 7 l/mn - Maxi : 13 l/mn
Using electrodes Ø 1.0 / 3.2 mm Ø 1.0 / 4.0 mm
Origin
equipment fitted
to the torch
Back Cap Long Long
Long Long
Nozzle Ø 12 mm Ø 12 mm
Electrode Ø 2.4 L Ø 2.4 L
WTT2 4 m 8 m
20W
RL S W000278893 W000278906
RL S
18W
RL S W000278897 W000278900
20W
RL C5B W000278894 W000278905
RL C5B
18W
RL C5B W000278898 W000278899
N°8695-1196_Rev2_05/2018
We thank you for your trust in our company by purchasing this equipment which will provide
you with complete satisfaction if you comply with its conditions for use and maintenance.
CAUTION: The company declines all responsibility in case of modification, addition of
components or subassemblies, or any transformation of the equipment carried out by
the customer or a thirdparty,without prior specific written agreement from the company.
Arc welding and plasma cutting may be dangerous for the operator and persons close
to the work area. Read the operating manual and safety instructions W000261712.
See www.weldline.eu.
A) Maintenance / Troubleshooting
Before any internal verifications and repair work, make sure that the equipment is separated
from the electric installation by electrical isolation (by electrical isolation is meant a group of
operations designed to separate and keep the equipment de-energized).
At least every six months, you must check the proper condition of the insulation and
connections of the electric equipment and accessories such as plugs, flexible wires, ducts,
connectors, extension leads, partholders, electrode-holders, or torches...
Maintenance and repair work on the jackets and insulating ducts must be carried out
extremely carefully.
Have defective parts repaired by a specialist, or better still, have them replaced.
Routinely check the proper tightening and cleanliness of the electric connections.
B) Work-station
Use only electrode holders and torches which are perfectly insulated.
The operator must be insulated from the ground-surface and the workpiece (gloves, safety
shoes, dry clothes, leather apron, and so forth...).
Do not touch the electrode wire and the part (or the nozzle) simultaneously.
C) Protection
It is absolutely essential that your protect your eyes from blinding glare (glare of arc invisible
light and infrared and ultraviolet radiation).
The welding mask, without or with helmet, must always be equipped with a protective filter
whose gradation depends on the welding arc current intensity (EN 169 Standard).
Fumes emitted during welding operations may be dangerous. Use adequate protection
means (fumes extraction, ventiled masks...)
Technical data
TIG manual torch with natural cooling
Safety instructions
French lever rangeErgonomic Range
WTT2 4 m 8 m
20W EB S W000278891 W000278911
EB S
18W EB S W000278895 W000278902
20W
EB C5B W000278892 W000278909
EB C5B
18W
EB C5B W000278896 W000278901
20W EB S/
C5B FLEX W000382786 W000382787
18W EB S/
C5B FLEX W000382788 W000382789
WTT2 20W
WTT2 18W
Instructions for safety, use and maintenance
EN
www.weldline.eu
LINCOLN ELECTRIC EUROPE S.L.
c/o Balmes, 89 - 8o2a- 08008 Barcelona - SPAIN
RL
EB
Options
Item number
W000306491 WTT 20WF
head
W000384994 WTT 18WF
head
Rep Item number WTT Spare parts
100 W000306488 20W Torch body
W000306503 18W
101 W000279230 20W RL handle
W000279231 18W
102 W000279227 20W Switch box + Sleeve
W000279229 18W
104 W000279233 20W-18W Microswitch
106 W000352104 20W-18W Trigger cable 2 wires
Rep Item number WTT Spare parts
107
W000279275 20W 4 m
Water Power cable
W000279276 8 m
W000279277 18W 4 m
W000279278 8 m
108 W000279286 20W Gas hose
W000168993 18W
109 W000279285 20W Water hose
W000352116 18W
110 W000168133 18W Ring hose D7
111.a W000141831 20W-18W Quick connection gas
Rep Item number WTT Spare parts
111.b W000270829 20W-18W Female connection M12x1
112 W000167244 20W-18W Water quick coupler
113 W000279240 20W-18W Blue and red stoppers
114 W000279265 20W-18W Water C connection
115 W000270832 STrigger male connection
116 W000270833 C5B Plug 5 pins
117 W000279284 20W EPDM Sheath
W000352112 18W
119 W000279423 20W-18W Pipe water return
Rep Item number WTT Spare parts
100 W000306488 20W Torch body
W000306503 18W
101 W000279263 20W EB handle
W000279264 18W
104 W000279241 20W-18W Microswitch
106 W000279287 20W-18W Trigger cable EB
107 W000279275 20W 4 m Water Power cable
W000279276 8 m
Rep Item number WTT Spare parts
107 W000279277 18W 4 m Water Power cable
W000279278 8 m
108 W000279286 20W Gas hose
W000168993 18W
109 W000279285 20W Water hose
W000352116 18W
110 W000168133 18W Ring hose D7
111.a W000141831 20W-18W Quick connection gas
111.b W000270829 20W-18W Female connection M12x1
Rep Item number WTT Spare parts
112 W000167244 20W-18W Water quick coupler
113 W000279240 20W-18W Blue and red stoppers
114 W000279265 20W-18W Water C connection
115 W000270832 20W-18W Trigger male connection
116 W000270833 C5B Plug 5 pins
117 W000279284 20W EPDM Sheath
W000352112 18W
119 W000279423 20W-18W Water inlet tube
Spare parts RL
Spare parts EB
Item number
W000141831
Quick connection Gas
For connection to ancient power
source, replacing the connection
M12x100
W000270829 Female Connection M12x1
EC Declaration of conformity
Manufacturer: LINCOLN ELECTRIC Europe
Hereby states that the manual welding torches WTT2 described in this
manual are conforms to the provisions of the “Low Voltage” Directives
(Directive 2006/95/CEE) and national legislation transposing it ; and
moreover declares that standards EN 60974-7 « Arc welding equipment.
Part 7 “Torches” » have been applied. This statement also applies to
versions of the aforementioned model.
This EC declaration of conformity guarantees that the equipment
delivered complies with the legislations in force, if it is used in
accordance with the enclosed instructions. Any different assembly or
modification renders our certification void. It is therefore recommended
that the manufacturer be consulted about any possible modification.
Failing that, the company which makes the modifications should ensure
the recertification. Should this occur, the new certification is not binding
on us in any way whatsoever. This document should be transmitted to
your technical or purchasing department for record purposes.
RoHS Declaration of conformity
Manufacturer: LINCOLN ELECTRIC Europe
Hereby states that the manual welding torches
WTT2 described in this manual are conforms to
the DIRECTIVE 2002/95/EC OF THE EUROPEAN
PARLIAMENT AND OF THE COUNCIL of 27
January 2003 (RoHS) on the restriction of the
use of certain hazardous substances in electrical
and electronic equipment while the parts do not
exceed the maximum concentrations of 0.1%
by weight in homogenous materials for lead,
mercury, hexavalent chromium, polybrominated
biphenyls (PBB) and polybrominated diphenyl
ethers (PBDE), and 0.01% for cadmium, as
required in Commission Decision 2005/618/EC
of 18 August 2005.
EN

EN
www.weldline.eu
LINCOLN ELECTRIC EUROPE S.L.
c/o Balmes, 89 - 8o2a- 08008 Barcelona - SPAIN
WTT2 20W 18W
Curent Duty cycle 60% 250 A 350 A
Duty cycle 100% 200 A 320 A
Light alloy welding, reduce the duty cycle about 30%
Water flow mini 1.0 l/mn
Water pressure 3.3 bars
Maxi temperature inlet water 45°C
Voltage class L - 113 V
Gas flow Mini : 7 l/mn - Maxi : 13 l/mn
Using electrodes Ø 1.0 / 3.2 mm Ø 1.0 / 4.0 mm
Origin
equipment fitted
to the torch
Back Cap Long Long
Long Long
Nozzle Ø 12 mm Ø 12 mm
Electrode Ø 2.4 L Ø 2.4 L
WTT2 4 m 8 m
20W
RL S W000278893 W000278906
RL S
18W
RL S W000278897 W000278900
20W
RL C5B W000278894 W000278905
RL C5B
18W
RL C5B W000278898 W000278899
N°8695-1196_Rev2_05/2018
We thank you for your trust in our company by purchasing this equipment which will provide
you with complete satisfaction if you comply with its conditions for use and maintenance.
CAUTION: The company declines all responsibility in case of modification, addition of
components or subassemblies, or any transformation of the equipment carried out by
the customer or a thirdparty,without prior specific written agreement from the company.
Arc welding and plasma cutting may be dangerous for the operator and persons close
to the work area. Read the operating manual and safety instructions W000261712.
See www.weldline.eu.
A) Maintenance / Troubleshooting
Before any internal verifications and repair work, make sure that the equipment is separated
from the electric installation by electrical isolation (by electrical isolation is meant a group of
operations designed to separate and keep the equipment de-energized).
At least every six months, you must check the proper condition of the insulation and
connections of the electric equipment and accessories such as plugs, flexible wires, ducts,
connectors, extension leads, partholders, electrode-holders, or torches...
Maintenance and repair work on the jackets and insulating ducts must be carried out
extremely carefully.
Have defective parts repaired by a specialist, or better still, have them replaced.
Routinely check the proper tightening and cleanliness of the electric connections.
B) Work-station
Use only electrode holders and torches which are perfectly insulated.
The operator must be insulated from the ground-surface and the workpiece (gloves, safety
shoes, dry clothes, leather apron, and so forth...).
Do not touch the electrode wire and the part (or the nozzle) simultaneously.
C) Protection
It is absolutely essential that your protect your eyes from blinding glare (glare of arc invisible
light and infrared and ultraviolet radiation).
The welding mask, without or with helmet, must always be equipped with a protective filter
whose gradation depends on the welding arc current intensity (EN 169 Standard).
Fumes emitted during welding operations may be dangerous. Use adequate protection
means (fumes extraction, ventiled masks...)
Technical data
TIG manual torch with natural cooling
Safety instructions
French lever rangeErgonomic Range
WTT2 4 m 8 m
20W EB S W000278891 W000278911
EB S
18W EB S W000278895 W000278902
20W
EB C5B W000278892 W000278909
EB C5B
18W
EB C5B W000278896 W000278901
20W EB S/
C5B FLEX W000382786 W000382787
18W EB S/
C5B FLEX W000382788 W000382789
WTT2 20W
WTT2 18W
Instructions for safety, use and maintenance
FR
www.weldline.eu
LINCOLN ELECTRIC EUROPE S.L.
c/o Balmes, 89 - 8o2a- 08008 Barcelona - SPAIN
Nous vous remercions de la confiance que vous nous avez accordée en acquérant cet
appareil qui vous donnera entière satisfaction si vous respectez ses conditions d’emploi
et d’entretien.
ATTENTION : la société est dégagée de toute responsabilité en cas de modification,
d’adjonction de composants ou de sous ensembles, ou d’une quelconque
transformation de l’appareil ou de l’installation, effectué par le client ou par un tiers,
sans un accord préalable spécifique écrit par la société elle-même.
Le soudage à l’arc et le coupage plasma peuvent être dangereux pour l’opérateur et
les personnes se trouvant à proximité de l’aire de travail. Lire le manuel d’utilisation
et l’instruction de sécurité W000261712. Voir www.weldline.eu.
A) Entretien / Dépannage
Avant toute vérification interne et réparation, vous devez vous assurer que l’appareil est
séparé de l’installation électrique par consignation (on entend par consignation, un ensemble
d’opérations destinées à séparer et à maintenir l’appareil hors tension).
Vous devez vérifier au moins tous les 6 mois le bon état d’isolement et les raccordements
des appareils et accessoires électriques, tels que prises,câbles souples, gaines, connecteurs,
prolongateurs, pinces de pièces, porte-électrodes ou torches...
Les travaux d’entretien et de réparation des enveloppes et gaines isolantes doivent être
effectuées minutieusement.
Faites réparer par un spécialiste, ou mieux faites lui remplacer les pièces défectueuses.
Vérifier périodiquement le bon serrage et la propreté des connections électriques.
B) Poste de travail
N’utilisez que des portes électrodes et torches parfaitement isolés.
L’opérateur doit être isolé du sol et de la pièce à souder (gants, chaussures de sécurité,
vêtements secs, tablier de cuir, etc...).
Ne pas toucher simultanément le fil électrode (ou la buse) et la pièce.
C) Sécurité
Il est indispensable de vous protéger les yeux contre les coups d’arc (éblouissement de l’arc
en lumière visible et les rayonnements infrarouge et ultraviolet).
Le masque de soudage, sans ou avec casque, doit toujours être muni d’un filtre protecteur
dont l’échelon dépend de l’intensité du courant de l’arc de soudage (Norme EN 169).
Les fumées émises au cours des opérations de soudage peuvent être nocives pour la santé.
Veillez à utiliser les moyens de protection adéquats (aspiration de fumées, masque ventilé…)
Données techniques
Torche manuelle TIG à refroidissement naturel
WTT2 20W 18W
Courant assigné Facteur de marche 60% 250 A 350 A
Facteur de marche 100% 200 A 320 A
Soudage des alliages légers, réduire le facteur de marche de 30%
Débit eau mini 1.0 l/mn
Pression d’eau 3.3 bars
Température maxi entrée eau 45°C
Classe de tension L - 113 V
Débit gaz Mini : 7 l/mn - Maxi : 13 l/mn
Electrodes utilisables Ø 1.0 / 3.2 mm Ø 1.0 / 4.0 mm
Equipement
d’origine monté
sur la torche
Bouchon Long Long
Long Long
Buse Ø 12 mm Ø 12 mm
Electrode Ø 2.4 L Ø 2.4 L
Instructions de Sécurité d’Utilisation et de Maintenance
Consignes de sécurité
WTT2 20W
WTT2 18W
La gamme ergonomique La gamme standard
N°8695-1196_Rev2_05/2018
WTT2 4 m 8 m
20W
RL S W000278893 W000278906
RL S
18W
RL S W000278897 W000278900
20W
RL C5B W000278894 W000278905
RL C5B
18W
RL C5B W000278898 W000278899
WTT2 4 m 8 m
20W EB S W000278891 W000278911
EB S
18W EB S W000278895 W000278902
20W
EB C5B W000278892 W000278909
EB C5B
18W
EB C5B W000278896 W000278901
20W EB S/
C5B FLEX W000382786 W000382787
18W EB S/
C5B FLEX W000382788 W000382789
FR

EN
www.weldline.eu
LINCOLN ELECTRIC EUROPE S.L.
c/o Balmes, 89 - 8o2a- 08008 Barcelona - SPAIN
WTT2 20W 18W
Curent Duty cycle 60% 250 A 350 A
Duty cycle 100% 200 A 320 A
Light alloy welding, reduce the duty cycle about 30%
Water flow mini 1.0 l/mn
Water pressure 3.3 bars
Maxi temperature inlet water 45°C
Voltage class L - 113 V
Gas flow Mini : 7 l/mn - Maxi : 13 l/mn
Using electrodes Ø 1.0 / 3.2 mm Ø 1.0 / 4.0 mm
Origin
equipment fitted
to the torch
Back Cap Long Long
Long Long
Nozzle Ø 12 mm Ø 12 mm
Electrode Ø 2.4 L Ø 2.4 L
WTT2 4 m 8 m
20W
RL S W000278893 W000278906
RL S
18W
RL S W000278897 W000278900
20W
RL C5B W000278894 W000278905
RL C5B
18W
RL C5B W000278898 W000278899
N°8695-1196_Rev2_05/2018
We thank you for your trust in our company by purchasing this equipment which will provide
you with complete satisfaction if you comply with its conditions for use and maintenance.
CAUTION: The company declines all responsibility in case of modification, addition of
components or subassemblies, or any transformation of the equipment carried out by
the customer or a thirdparty, without prior specific written agreement from the company.
Arc welding and plasma cutting may be dangerous for the operator and persons close
to the work area. Read the operating manual and safety instructions W000261712.
See www.weldline.eu.
A) Maintenance / Troubleshooting
Before any internal verifications and repair work, make sure that the equipment is separated
from the electric installation by electrical isolation (by electrical isolation is meant a group of
operations designed to separate and keep the equipment de-energized).
At least every six months, you must check the proper condition of the insulation and
connections of the electric equipment and accessories such as plugs, flexible wires, ducts,
connectors, extension leads, partholders, electrode-holders, or torches...
Maintenance and repair work on the jackets and insulating ducts must be carried out
extremely carefully.
Have defective parts repaired by a specialist, or better still, have them replaced.
Routinely check the proper tightening and cleanliness of the electric connections.
B) Work-station
Use only electrode holders and torches which are perfectly insulated.
The operator must be insulated from the ground-surface and the workpiece (gloves, safety
shoes, dry clothes, leather apron, and so forth...).
Do not touch the electrode wire and the part (or the nozzle) simultaneously.
C) Protection
It is absolutely essential that your protect your eyes from blinding glare (glare of arc invisible
light and infrared and ultraviolet radiation).
The welding mask, without or with helmet, must always be equipped with a protective filter
whose gradation depends on the welding arc current intensity (EN 169 Standard).
Fumes emitted during welding operations may be dangerous. Use adequate protection
means (fumes extraction, ventiled masks...)
Technical data
TIG manual torch with natural cooling
Safety instructions
French lever rangeErgonomic Range
WTT2 4 m 8 m
20W EB S W000278891 W000278911
EB S
18W EB S W000278895 W000278902
20W
EB C5B W000278892 W000278909
EB C5B
18W
EB C5B W000278896 W000278901
20W EB S/
C5B FLEX W000382786 W000382787
18W EB S/
C5B FLEX W000382788 W000382789
WTT2 20W
WTT2 18W
Instructions for safety, use and maintenance
FR
www.weldline.eu
LINCOLN ELECTRIC EUROPE S.L.
c/o Balmes, 89 - 8o2a- 08008 Barcelona - SPAIN
Pièces d’usure
Commandes gâchette simple
Maintenance simplifiée.
REP WTT2
20W
WTT2
18W Ø Pièces d’usure
6L
W000306456 / 4.8
Buse longue
W000306457 W000306462 6.4
W000306458 W000306463 8.0
W000306459 W000306464 9.6
/ W000306465 11.2
7 / W000306466 // Bague Gas Lens
8
W000306385 W000306389 1.0
Siège Gas Lens
W000306386 W000306390 1.6
W000306460 / 2.0
W000306387 W000306391 2.4
W000306388 W000306392 3.2
/ W000306393 4.0
9
W000306429 W000306434 6.4
Buse Gas Lens
/ W000306435 8.0
W000306431 W000306436 9.6
W000306432 W000306437 11.2
W000306433 W000306438 12.8
W000306438 16.0
9L
/ W000306467 8.0
Buse Longue Gas
Lens
/ W000306468 9.6
/ W000306469 11.2
/ W000306470 12.8
REP WTT2
20W
WTT2
18W Ø Pièces d’usure
1
W000306398 W000306399 // Bouchon court
W000306400 / // Bouchon moyen
W000306402 W000306403 // Bouchon long
2 W000306404 W000306405 // Joint de bouchon
3 W000306396 W000306397 // Bague d’étanchéité
4
W000306406 W000306411 1.0
Pince
W000306407 W000306412 1.6
W000306408 W000306413 2.0
W000306409 W000306414 2.4
W000306410 W000306415 3.2
/ W000306416 4.0
5
W000306376 W000306380 1.0
Siège
W000306377 W000306381 1.6
W000306378 W000270781 2.0
W000306455 W000306382 2.4
W000306379 W000306383 3.2
/ W000306384 4.0
6
W000306417 W000306423 6.4
Buse
W000306418 W000306424 8.0
W000306419 W000306425 9.6
W000306420 W000306426 11.2
W000306421 W000306427 12.8
W000306422 W000306428 16.0
/ W000306461 19.2
Kit B
W000279241
Kit L
W000279245
1 4
23
1
4
3
5
6L
6
7
8
L
L
9
2
9L
Changement
de connecteur de gaz
FR

EN
www.weldline.eu
LINCOLN ELECTRIC EUROPE S.L.
c/o Balmes, 89 - 8o2a- 08008 Barcelona - SPAIN
WTT2 20W 18W
Curent Duty cycle 60% 250 A 350 A
Duty cycle 100% 200 A 320 A
Light alloy welding, reduce the duty cycle about 30%
Water flow mini 1.0 l/mn
Water pressure 3.3 bars
Maxi temperature inlet water 45°C
Voltage class L - 113 V
Gas flow Mini : 7 l/mn - Maxi : 13 l/mn
Using electrodes Ø 1.0 / 3.2 mm Ø 1.0 / 4.0 mm
Origin
equipment fitted
to the torch
Back Cap Long Long
Long Long
Nozzle Ø 12 mm Ø 12 mm
Electrode Ø 2.4 L Ø 2.4 L
WTT2 4 m 8 m
20W
RL S W000278893 W000278906
RL S
18W
RL S W000278897 W000278900
20W
RL C5B W000278894 W000278905
RL C5B
18W
RL C5B W000278898 W000278899
N°8695-1196_Rev2_05/2018
We thank you for your trust in our company by purchasing this equipment which will provide
you with complete satisfaction if you comply with its conditions for use and maintenance.
CAUTION: The company declines all responsibility in case of modification, addition of
components or subassemblies, or any transformation of the equipment carried out by
the customer or a thirdparty, without prior specific written agreement from the company.
Arc welding and plasma cutting may be dangerous for the operator and persons close
to the work area. Read the operating manual and safety instructions W000261712.
See www.weldline.eu.
A) Maintenance / Troubleshooting
Before any internal verifications and repair work, make sure that the equipment is separated
from the electric installation by electrical isolation (by electrical isolation is meant a group of
operations designed to separate and keep the equipment de-energized).
At least every six months, you must check the proper condition of the insulation and
connections of the electric equipment and accessories such as plugs, flexible wires, ducts,
connectors, extension leads, partholders, electrode-holders, or torches...
Maintenance and repair work on the jackets and insulating ducts must be carried out
extremely carefully.
Have defective parts repaired by a specialist, or better still, have them replaced.
Routinely check the proper tightening and cleanliness of the electric connections.
B) Work-station
Use only electrode holders and torches which are perfectly insulated.
The operator must be insulated from the ground-surface and the workpiece (gloves, safety
shoes, dry clothes, leather apron, and so forth...).
Do not touch the electrode wire and the part (or the nozzle) simultaneously.
C) Protection
It is absolutely essential that your protect your eyes from blinding glare (glare of arc invisible
light and infrared and ultraviolet radiation).
The welding mask, without or with helmet, must always be equipped with a protective filter
whose gradation depends on the welding arc current intensity (EN 169 Standard).
Fumes emitted during welding operations may be dangerous. Use adequate protection
means (fumes extraction, ventiled masks...)
Technical data
TIG manual torch with natural cooling
Safety instructions
French lever rangeErgonomic Range
WTT2 4 m 8 m
20W EB S W000278891 W000278911
EB S
18W EB S W000278895 W000278902
20W
EB C5B W000278892 W000278909
EB C5B
18W
EB C5B W000278896 W000278901
20W EB S/
C5B FLEX W000382786 W000382787
18W EB S/
C5B FLEX W000382788 W000382789
WTT2 20W
WTT2 18W
Instructions for safety, use and maintenance
FR
www.weldline.eu
LINCOLN ELECTRIC EUROPE S.L.
c/o Balmes, 89 - 8o2a- 08008 Barcelona - SPAIN
Pièces de rechange RL
Pièces de rechange EB
N° article
W000141831
Connexion gaz rapide
Pour branchement sur
ancienne source de puissance,
en remplacement du raccord
vissé 12x100
W000270829 Raccord femelle M12x1
Options
N° article
W000306491 Corps
WTT 20WF
W000384994 Corps
WTT 18WF
Déclaration de conformité CE
Fabricant : LINCOLN ELECTRIC Europe
Déclare ci-après que les torches de soudage manuel WTT2 décrites
dans ce guide d’emploi sont conforme aux dispositions des Directives
« Basse tension » (Directive 2006/95/CEE),et aux législations nationales la
transposant ; et déclare par ailleurs que la norme EN 60974-7 « Matériel
de soudage à l’arc. Partie 7:“Torches” » a été appliquée. Cette déclaration
s’applique également aux versions dérivées du modèle cité ci-dessus.
Cette déclaration CE de conformité garantit que le matériel livré
respecte la législation en vigueur, s’il est utilisé conformément à la
notice d’instruction jointe.Tout montage différent ou toute modification
entraîne la nullité de notre certification. Il est donc recommandé pour
toute modification éventuelle de faire appel au constructeur. A défaut,
l’entreprise réalisant les modifications doit refaire la certification.
Dans ce cas, cette nouvelle certification ne saurait nous engager de
quelque façon que ce soit. Ce document doit être transmis à votre
service technique ou votre service achat, pour archivage.
Déclaration de conformité RoHS
Fabricant : LINCOLN ELECTRIC Europe
Déclare ci-après que les torches de soudage
manuel WTT2 décrites dans ce guide d’emploi
sont conformes à la DIRECTIVE 2002/95/CE DU
PARLEMENT EUROPÉEN ET DU CONSEIL du 27
janvier 2003 (RoHS) relative à la limitation de
l’utilisation de certaines substances dangereuses
dans les équipements électriques et électroniques
car les éléments n’excèdent pas la concentration
maximale dans les matériaux homogènes de 0,1
% en poids de plomb, de mercure, de chrome
hexavalent, de polybromobiphényles (PBB) et de
polybromobiphényléthers (PBDE) ainsi qu’une
concentration maximale de 0,01 % en poids
de cadmium comme exigé par DÉCISION DE LA
COMMISSION 2005/618/EC du 18 Août 2005.
RL
Rep N° article WTT Pièces de rechange
100 W000306488 20W Corps de torche
W000306503 18W
101 W000279230 20W Manche RL
W000279231 18W
102 W000279227 20W Boitier gâchette
+ manchette
W000279229 18W
104 W000279233 20W-18W Microrupteur
106 W000352104 20W-18W Câble 2 conducteurs
Rep N° article WTT Pièces de rechange
107
W000279275 20W 4 m
Canalisation
eauélectricité
W000279276 8 m
W000279277 18W 4 m
W000279278 8 m
108 W000279286 20W Tuyau Gaz
W000168993 18W
109 W000279285 20W Tuyau Eau
W000352116 18W
110 W000168133 18W Collier tuyau D7
111.a W000141831 20W-18W Connexion rapide gaz
Rep N° article WTT Pièces de rechange
111.b W000270829 20W-18W Raccord femelle M12x1
112 W000167244 20W-18W Coupleur rapide eau
113 W000279240 20W-18W Bouchons bleu et rouge
114 W000279265 20W-18W Fiche C eau
115 W000270832 SFiche male gâchette
116 W000270833 C5B Fiche 5 broches
117 W000279284 20W Gaine EPDM
W000352112 18W
119 W000279423 20W-18W Canalisation retour eau
Rep N° article WTT Pièces de rechange
100 W000306488 20W Corps de torche
W000306503 18W
101 W000279263 20W Manche EB
W000279264 18W
104 W000279241 20W-18W Microrupteur
106 W000279287 20W-18W Câble gâchette EB
107 W000279275 20W 4 m Canalisation
eauélectricité
W000279276 8 m
Rep N° article WTT Pièces de rechange
107 W000279277 18W 4 m Canalisation
eauélectricité
W000279278 8 m
108 W000279286 20W Tuyau Gaz
W000168993 18W
109 W000279285 20W Tuyau Eau
W000352116 18W
110 W000168133 18W Collier tuyau D7
111.a W000141831 20W-18W Connexion rapide gaz
111.b W000270829 20W-18W Raccord femelle M12x1
Rep N° article WTT Pièces de rechange
112 W000167244 20W-18W Coupleur rapide eau
113 W000279240 20W-18W Bouchons bleu et rouge
114 W000279265 20W-18W Fiche C eau
115 W000270832 20W-18W Fiche male gâchette
116 W000270833 C5B Fiche 5 broches
117 W000279284 20W Gaine EPDM
W000352112 18W
119 W000279423 20W-18W Canalisation entrée eau
EB
FR

EN
www.weldline.eu
LINCOLN ELECTRIC EUROPE S.L.
c/o Balmes, 89 - 8o2a- 08008 Barcelona - SPAIN
WTT2 20W 18W
Curent Duty cycle 60% 250 A 350 A
Duty cycle 100% 200 A 320 A
Light alloy welding, reduce the duty cycle about 30%
Water flow mini 1.0 l/mn
Water pressure 3.3 bars
Maxi temperature inlet water 45°C
Voltage class L - 113 V
Gas flow Mini : 7 l/mn - Maxi : 13 l/mn
Using electrodes Ø 1.0 / 3.2 mm Ø 1.0 / 4.0 mm
Origin
equipment fitted
to the torch
Back Cap Long Long
Long Long
Nozzle Ø 12 mm Ø 12 mm
Electrode Ø 2.4 L Ø 2.4 L
WTT2 4 m 8 m
20W
RL S W000278893 W000278906
RL S
18W
RL S W000278897 W000278900
20W
RL C5B W000278894 W000278905
RL C5B
18W
RL C5B W000278898 W000278899
N°8695-1196_Rev2_05/2018
We thank you for your trust in our company by purchasing this equipment which will provide
you with complete satisfaction if you comply with its conditions for use and maintenance.
CAUTION: The company declines all responsibility in case of modification, addition of
components or subassemblies, or any transformation of the equipment carried out by
the customer or a thirdparty, without prior specific written agreement from the company.
Arc welding and plasma cutting may be dangerous for the operator and persons close
to the work area. Read the operating manual and safety instructions W000261712.
See www.weldline.eu.
A) Maintenance / Troubleshooting
Before any internal verifications and repair work, make sure that the equipment is separated
from the electric installation by electrical isolation (by electrical isolation is meant a group of
operations designed to separate and keep the equipment de-energized).
At least every six months, you must check the proper condition of the insulation and
connections of the electric equipment and accessories such as plugs, flexible wires, ducts,
connectors, extension leads, partholders, electrode-holders, or torches...
Maintenance and repair work on the jackets and insulating ducts must be carried out
extremely carefully.
Have defective parts repaired by a specialist, or better still, have them replaced.
Routinely check the proper tightening and cleanliness of the electric connections.
B) Work-station
Use only electrode holders and torches which are perfectly insulated.
The operator must be insulated from the ground-surface and the workpiece (gloves, safety
shoes, dry clothes, leather apron, and so forth...).
Do not touch the electrode wire and the part (or the nozzle) simultaneously.
C) Protection
It is absolutely essential that your protect your eyes from blinding glare (glare of arc invisible
light and infrared and ultraviolet radiation).
The welding mask, without or with helmet, must always be equipped with a protective filter
whose gradation depends on the welding arc current intensity (EN 169 Standard).
Fumes emitted during welding operations may be dangerous. Use adequate protection
means (fumes extraction, ventiled masks...)
Technical data
TIG manual torch with natural cooling
Safety instructions
French lever rangeErgonomic Range
WTT2 4 m 8 m
20W EB S W000278891 W000278911
EB S
18W EB S W000278895 W000278902
20W
EB C5B W000278892 W000278909
EB C5B
18W
EB C5B W000278896 W000278901
20W EB S/
C5B FLEX W000382786 W000382787
18W EB S/
C5B FLEX W000382788 W000382789
WTT2 20W
WTT2 18W
Instructions for safety, use and maintenance
IT
www.weldline.eu
LINCOLN ELECTRIC EUROPE S.L.
c/o Balmes, 89 - 8o2a- 08008 Barcelona - SPAIN
WTT2 20W 18W
Corrente assegnata Fattore di marcia 60% 250 A 350 A
Fattore di marcia 100% 200 A 320 A
Saldatura delle leghe leggere, ridurre il fattore di marcia del 30%
Portata minima dell’acqua 1.0 l/mn
Pressione acqua 3.3 bars
Temperatura massima di entrata acqua 45°C
Classe di tensione L - 113 V
Portata di gas Mini : 7 l/mn - Maxi : 13 l/mn
Elettrodo utilizzabili Ø 1.0 / 3.2 mm Ø 1.0 / 4.0 mm
Attrezzato
originario
Tappo Long Long
Long Long
Ugello Ø 12 mm Ø 12 mm
Electtrodo Ø 2.4 L Ø 2.4 L
WTT2 20W
WTT2 18W
N°8695-1196_Rev2_05/2018
Vi ringraziamo per la fiducia dimostrataci acquistando questo apparecchio che vi darà
piena soddisfazione qualora rispettiate le sue condizioni d’impiego e di manutenzione.
ATTENZIONE: la società viene sollevata da ogni responsabilità in caso di modifica,
di aggiunta di componenti o di sottoassiemi, o di una qualunque trasformazione
dell’apparecchio, eseguiti dal cliente o da terzi, senza un accordo preventivo scritto
della società stessa.
Saldatura ad arco e taglio plasma possono essere pericolosi sia per l’operatore sia
per le persone d’intorno. Leggere attentamente il manuale d’uso e le prescrizioni di
sicurezza W000261712. Visualizza www.weldline.eu.
A) Manutenzione / Riparazione
Prima di qualsiasi verifica interna e riparazione, dovete assicurarvi che l’apparecchio sia
scollegato dall’impianto elettrico mediante un dispositivo di divieto di accesso (con il termine
“divieto di accesso”, si intende una serie di operazione destinate a separare e a mantenere
l’apparecchio fuori tensione).
Dovete verificare almeno ogni 6 mesi il buono stato dell’isolamento ed i collegamenti
degli apparecchi e degli accessori elettrici, come prese, cavi flessibili, guaine, conduttori,
prolunghe, pinze di pezzi, portaelettrodi o torce...
Gli interventi di manutenzione e di riparazione degli involucri e delle guaine isolanti devono
essere eseguiti accuratamente.
Fate riparare da uno specialisti, o meglio fategli sostituire i pezzi difettosi.
Verificate periodicamente il buon serraggio e la pulizia dei collegamenti elettrici.
B) Posto di lavoro
Utilizzate soltanto portaelettrodi e torce perfettamente isolati.
L’operatore deve essere isolato dal suolo e dal pezzo da saldare (guanti, scarpe di sicurezza,
vestiti asciutti, grembiule di cuoio, ...).
Non toccare contemporaneamente il filo elettrodo (o l’ugello) ed il pezzo.
C) Sicurezza
E’ indispensabile proteggere i vostri occhi contro i colpi d’arco (abbagliamento dell’arco in
luce visibile e le radiazioni infrarossi ed ultravioletti).
La maschera di saldatura, con o senza maschera, deve sempre essere dotata di un filtro
protettore, la cui graduazione dipende dell’intensità della corrente dell’arco di saldatura
(Norma EN 169).
I fumi emessi durante la saldatura possono essere dannosi per la salute. Usare appropriate
protezioni tipo (aspiratori o maschere ventilate...)
Dati technici
Torce manuali TIG con raffreddamento mediante naturale
Istruzioni per la sicurezza nell’uso e per la manutenzione
Raccomandazioni di sicurezza
La gamma ergonomica La gamma standard
WTT2 4 m 8 m
20W
RL S W000278893 W000278906
RL S
18W
RL S W000278897 W000278900
20W
RL C5B W000278894 W000278905
RL C5B
18W
RL C5B W000278898 W000278899
WTT2 4 m 8 m
20W EB S W000278891 W000278911
EB S
18W EB S W000278895 W000278902
20W
EB C5B W000278892 W000278909
EB C5B
18W
EB C5B W000278896 W000278901
20W EB S/
C5B FLEX W000382786 W000382787
18W EB S/
C5B FLEX W000382788 W000382789
IT

EN
www.weldline.eu
LINCOLN ELECTRIC EUROPE S.L.
c/o Balmes, 89 - 8o2a- 08008 Barcelona - SPAIN
WTT2 20W 18W
Curent Duty cycle 60% 250 A 350 A
Duty cycle 100% 200 A 320 A
Light alloy welding, reduce the duty cycle about 30%
Water flow mini 1.0 l/mn
Water pressure 3.3 bars
Maxi temperature inlet water 45°C
Voltage class L - 113 V
Gas flow Mini : 7 l/mn - Maxi : 13 l/mn
Using electrodes Ø 1.0 / 3.2 mm Ø 1.0 / 4.0 mm
Origin
equipment fitted
to the torch
Back Cap Long Long
Long Long
Nozzle Ø 12 mm Ø 12 mm
Electrode Ø 2.4 L Ø 2.4 L
WTT2 4 m 8 m
20W
RL S W000278893 W000278906
RL S
18W
RL S W000278897 W000278900
20W
RL C5B W000278894 W000278905
RL C5B
18W
RL C5B W000278898 W000278899
N°8695-1196_Rev2_05/2018
We thank you for your trust in our company by purchasing this equipment which will provide
you with complete satisfaction if you comply with its conditions for use and maintenance.
CAUTION: The company declines all responsibility in case of modification, addition of
components or subassemblies, or any transformation of the equipment carried out by
the customer or a thirdparty, without prior specific written agreement from the company.
Arc welding and plasma cutting may be dangerous for the operator and persons close
to the work area. Read the operating manual and safety instructions W000261712.
See www.weldline.eu.
A) Maintenance / Troubleshooting
Before any internal verifications and repair work, make sure that the equipment is separated
from the electric installation by electrical isolation (by electrical isolation is meant a group of
operations designed to separate and keep the equipment de-energized).
At least every six months, you must check the proper condition of the insulation and
connections of the electric equipment and accessories such as plugs, flexible wires, ducts,
connectors, extension leads, partholders, electrode-holders, or torches...
Maintenance and repair work on the jackets and insulating ducts must be carried out
extremely carefully.
Have defective parts repaired by a specialist, or better still, have them replaced.
Routinely check the proper tightening and cleanliness of the electric connections.
B) Work-station
Use only electrode holders and torches which are perfectly insulated.
The operator must be insulated from the ground-surface and the workpiece (gloves, safety
shoes, dry clothes, leather apron, and so forth...).
Do not touch the electrode wire and the part (or the nozzle) simultaneously.
C) Protection
It is absolutely essential that your protect your eyes from blinding glare (glare of arc invisible
light and infrared and ultraviolet radiation).
The welding mask, without or with helmet, must always be equipped with a protective filter
whose gradation depends on the welding arc current intensity (EN 169 Standard).
Fumes emitted during welding operations may be dangerous. Use adequate protection
means (fumes extraction, ventiled masks...)
Technical data
TIG manual torch with natural cooling
Safety instructions
French lever rangeErgonomic Range
WTT2 4 m 8 m
20W EB S W000278891 W000278911
EB S
18W EB S W000278895 W000278902
20W
EB C5B W000278892 W000278909
EB C5B
18W
EB C5B W000278896 W000278901
20W EB S/
C5B FLEX W000382786 W000382787
18W EB S/
C5B FLEX W000382788 W000382789
WTT2 20W
WTT2 18W
Instructions for safety, use and maintenance
IT
www.weldline.eu
LINCOLN ELECTRIC EUROPE S.L.
c/o Balmes, 89 - 8o2a- 08008 Barcelona - SPAIN
Trigger semplici comandi
Manutenzione semplificata.
Pezzi di usura
1
4
3
5
6L
6
7
8
L
L
9
2
9L
REP WTT2
20W
WTT2
18W Ø Pezzi di usura
6L
W000306456 / 4.8
Ugello lungo
W000306457 W000306462 6.4
W000306458 W000306463 8.0
W000306459 W000306464 9.6
/ W000306465 11.2
7 / W000306466 // Anello Gas Lens
8
W000306385 W000306389 1.0
Sede Gas Lens
W000306386 W000306390 1.6
W000306460 / 2.0
W000306387 W000306391 2.4
W000306388 W000306392 3.2
/ W000306393 4.0
9
W000306429 W000306434 6.4
Gas Lens ugello
/ W000306435 8.0
W000306431 W000306436 9.6
W000306432 W000306437 11.2
W000306433 W000306438 12.8
W000306438 16.0
9L
/ W000306467 8.0
Gas Lens
ugello lung
/ W000306468 9.6
/ W000306469 11.2
/ W000306470 12.8
REP WTT2
20W
WTT2
18W Ø Pezzi di usura
1
W000306398 W000306399 // Tappo corto
W000306400 / // Tappo medio
W000306402 W000306403 // Tappo lungo
2 W000306404 W000306405 // O’Ring
3 W000306396 W000306397 // Anello di tenuta
4
W000306406 W000306411 1.0
Pinza
W000306407 W000306412 1.6
W000306408 W000306413 2.0
W000306409 W000306414 2.4
W000306410 W000306415 3.2
/ W000306416 4.0
5
W000306376 W000306380 1.0
Sede
W000306377 W000306381 1.6
W000306378 W000270781 2.0
W000306455 W000306382 2.4
W000306379 W000306383 3.2
/ W000306384 4.0
6
W000306417 W000306423 6.4
Ugello
W000306418 W000306424 8.0
W000306419 W000306425 9.6
W000306420 W000306426 11.2
W000306421 W000306427 12.8
W000306422 W000306428 16.0
/ W000306461 19.2
Kit B
W000279241
Kit L
W000279245
1 4
23
Cambio del connettore del gas
IT

EN
www.weldline.eu
LINCOLN ELECTRIC EUROPE S.L.
c/o Balmes, 89 - 8o2a- 08008 Barcelona - SPAIN
WTT2 20W 18W
Curent Duty cycle 60% 250 A 350 A
Duty cycle 100% 200 A 320 A
Light alloy welding, reduce the duty cycle about 30%
Water flow mini 1.0 l/mn
Water pressure 3.3 bars
Maxi temperature inlet water 45°C
Voltage class L - 113 V
Gas flow Mini : 7 l/mn - Maxi : 13 l/mn
Using electrodes Ø 1.0 / 3.2 mm Ø 1.0 / 4.0 mm
Origin
equipment fitted
to the torch
Back Cap Long Long
Long Long
Nozzle Ø 12 mm Ø 12 mm
Electrode Ø 2.4 L Ø 2.4 L
WTT2 4 m 8 m
20W
RL S W000278893 W000278906
RL S
18W
RL S W000278897 W000278900
20W
RL C5B W000278894 W000278905
RL C5B
18W
RL C5B W000278898 W000278899
N°8695-1196_Rev2_05/2018
We thank you for your trust in our company by purchasing this equipment which will provide
you with complete satisfaction if you comply with its conditions for use and maintenance.
CAUTION: The company declines all responsibility in case of modification, addition of
components or subassemblies, or any transformation of the equipment carried out by
the customer or a thirdparty, without prior specific written agreement from the company.
Arc welding and plasma cutting may be dangerous for the operator and persons close
to the work area. Read the operating manual and safety instructions W000261712.
See www.weldline.eu.
A) Maintenance / Troubleshooting
Before any internal verifications and repair work, make sure that the equipment is separated
from the electric installation by electrical isolation (by electrical isolation is meant a group of
operations designed to separate and keep the equipment de-energized).
At least every six months, you must check the proper condition of the insulation and
connections of the electric equipment and accessories such as plugs, flexible wires, ducts,
connectors, extension leads, partholders, electrode-holders, or torches...
Maintenance and repair work on the jackets and insulating ducts must be carried out
extremely carefully.
Have defective parts repaired by a specialist, or better still, have them replaced.
Routinely check the proper tightening and cleanliness of the electric connections.
B) Work-station
Use only electrode holders and torches which are perfectly insulated.
The operator must be insulated from the ground-surface and the workpiece (gloves, safety
shoes, dry clothes, leather apron, and so forth...).
Do not touch the electrode wire and the part (or the nozzle) simultaneously.
C) Protection
It is absolutely essential that your protect your eyes from blinding glare (glare of arc invisible
light and infrared and ultraviolet radiation).
The welding mask, without or with helmet, must always be equipped with a protective filter
whose gradation depends on the welding arc current intensity (EN 169 Standard).
Fumes emitted during welding operations may be dangerous. Use adequate protection
means (fumes extraction, ventiled masks...)
Technical data
TIG manual torch with natural cooling
Safety instructions
French lever rangeErgonomic Range
WTT2 4 m 8 m
20W EB S W000278891 W000278911
EB S
18W EB S W000278895 W000278902
20W
EB C5B W000278892 W000278909
EB C5B
18W
EB C5B W000278896 W000278901
20W EB S/
C5B FLEX W000382786 W000382787
18W EB S/
C5B FLEX W000382788 W000382789
WTT2 20W
WTT2 18W
Instructions for safety, use and maintenance
IT
www.weldline.eu
LINCOLN ELECTRIC EUROPE S.L.
c/o Balmes, 89 - 8o2a- 08008 Barcelona - SPAIN
Options
Codice articolo
W000306491 Corpo
WTT 20WF
W000384994 Corpo
WTT 18WF
Pezzi di ricambi RL
Pezzi di ricambi EB
Codice articolo
W000141831
Connessione rapida di gas
Per il collegamento alla fonte di
alimentazione antica, in sostituzione
del collegamento M12x100
W000270829 Raccordo femmina M12x1
Dichiarazione di conformità CE
Fabbricante: LINCOLN ELECTRIC Europe
Dichiara qui di seguito che il torce manuali WTT2 è conforme alle
disposizioni delle Direttive „Bassa tensione“ (Direttiva 2006/95/CEE), e alle
legislazioni nazionali corrispondenti ; e dichiara inoltre che le norme EN 60
974-7 « Regole di sicurezza per il materiale da saldatura elettrico Parte 7:
„Torce“ ». sono state applicate. Questa dichiarazione si applica anche alle
versioni derivate e ai riferimenti del modello sopra.
Questa dichirazione di conformità CE garantisce che il materiale consegnatoLe,
se utilizzato nel rispetto delle istruzioni accluse, è conforme alle norme
vigenti. Un’installazione diversa da quella auspicata o qualsiasi modifica
comporta l’annullamento della nostra certificazione. Per eventuali modifiche,
si raccomanda pertanto di rivolgersi direttamente all’azienda costruttrice. Se
quest’ultima non viene avvertita, la ditta che effectuerà le modifiche dovrà
procedere a un nuova certificazione. In questo caso, la nuova certificazione
non rappresenterà, in nessuna eventualità, un impegno da parte nostra.
Questo documento dev’essere trasmesso al servizo Tecnico a Acquisti della
Sua azienda per archiviazione.
Dichiarazione
di conformità RoHS
Fabbricante: LINCOLN ELECTRIC Europe
Dichiara qui di seguito che il torce manuali
WTT2 è conforme alle disposizioni delle la
DIRETTIVA 2002/95/EC DEL PARLAMENTO
EUROPEO E DEL CONSIGLIO del 27 Gennaio
2003 (RoHS) sulla restrizione dell’uso di
determinate sostanze pericolose nelle
apparecchiature elettriche ed elettroniche i
componenti non eccedono la concentrazione
massima in materiali omogenei del 0.1%
in peso di piombo, mercurio, cromo
esavalente, bifenili polibromurati (PBB) o
etere di difenile polibromurato (PBDE) e
lo 0.01% di cadmio, come richiesto nella
decisione della Commissione 2005/618/EC
del 18 Agosto 2005; oppure.
EB
RL
Rep Codice articolo
WTT Pezzi di ricambi
100 W000306488 20W Corpo
W000306503 18W
101 W000279230 20W Manico RL
W000279231 18W
102 W000279227 20W Contenitore grilletto
+ Manica
W000279229 18W
104 W000279233 20W-18W Microinterruttore
106 W000352104 20W-18W Cavo 2 conduttori
Rep Codice articolo
WTT Pezzi di ricambi
107
W000279275 20W 4 m
Tubazione
acquaelettricità
W000279276 8 m
W000279277 18W 4 m
W000279278 8 m
108 W000279286 20W Tubo gas
W000168993 18W
109 W000279285 20W Tubo acqua
W000352116 18W
110 W000168133 18W Collare tubo D7
111.a W000141831 20W-18W Connessione rapida gas
Rep Codice articolo
WTT Pezzi di ricambi
111.b W000270829 20W-18W Raccordo femmina M12x1
112 W000167244 20W-18W Accoppiatore rapido acqua
113 W000279240 20W-18W Blue rosso tappi
114 W000279265 20W-18W Spina compatta acqua
115 W000270832 SConnettore a spina grilletto
116 W000270833 C5B Spina 5 spinotti
117 W000279284 20W Guaina in EPDM
W000352112 18W
119 W000279423 20W-18W Tubo di acqua di ritorno
Rep Codice articolo
WTT Pezzi di ricambi
100 W000306488 20W Corpo
W000306503 18W
101 W000279263 20W Manico EB
W000279264 18W
104 W000279241 20W-18W Microinterruttore
106 W000279287 20W-18W Cavo Grilleto EB
107 W000279275 20W 4 m Tubazione
acquaelettricità
W000279276 8 m
Rep Codice articolo
WTT Pezzi di ricambi
107 W000279277 18W 4 m Tubazione
acquaelettricità
W000279278 8 m
108 W000279286 20W Tubo gas
W000168993 18W
109 W000279285 20W Tubo acqua
W000352116 18W
110 W000168133 18W Collare tubo D7
111.a W000141831 20W-18W Connessione rapida gas
111.b W000270829 20W-18W Raccordo femmina M12x1
Rep Codice articolo
WTT Pezzi di ricambi
112 W000167244 20W-18W Accoppiatore rapido acqua
113 W000279240 20W-18W Blue rosso tappi
114 W000279265 20W-18W Spina compatta acqua
115 W000270832 20W-18W Connettore a spina grilletto
116 W000270833 C5B Spina 5 spinotti
117 W000279284 20W Guaina in EPDM
W000352112 18W
119 W000279423 20W-18W Tubo di acqua di ritorno
IT

EN
www.weldline.eu
LINCOLN ELECTRIC EUROPE S.L.
c/o Balmes, 89 - 8o2a- 08008 Barcelona - SPAIN
WTT2 20W 18W
Curent Duty cycle 60% 250 A 350 A
Duty cycle 100% 200 A 320 A
Light alloy welding, reduce the duty cycle about 30%
Water flow mini 1.0 l/mn
Water pressure 3.3 bars
Maxi temperature inlet water 45°C
Voltage class L - 113 V
Gas flow Mini : 7 l/mn - Maxi : 13 l/mn
Using electrodes Ø 1.0 / 3.2 mm Ø 1.0 / 4.0 mm
Origin
equipment fitted
to the torch
Back Cap Long Long
Long Long
Nozzle Ø 12 mm Ø 12 mm
Electrode Ø 2.4 L Ø 2.4 L
WTT2 4 m 8 m
20W
RL S W000278893 W000278906
RL S
18W
RL S W000278897 W000278900
20W
RL C5B W000278894 W000278905
RL C5B
18W
RL C5B W000278898 W000278899
N°8695-1196_Rev2_05/2018
We thank you for your trust in our company by purchasing this equipment which will provide
you with complete satisfaction if you comply with its conditions for use and maintenance.
CAUTION: The company declines all responsibility in case of modification, addition of
components or subassemblies, or any transformation of the equipment carried out by
the customer or a thirdparty, without prior specific written agreement from the company.
Arc welding and plasma cutting may be dangerous for the operator and persons close
to the work area. Read the operating manual and safety instructions W000261712.
See www.weldline.eu.
A) Maintenance / Troubleshooting
Before any internal verifications and repair work, make sure that the equipment is separated
from the electric installation by electrical isolation (by electrical isolation is meant a group of
operations designed to separate and keep the equipment de-energized).
At least every six months, you must check the proper condition of the insulation and
connections of the electric equipment and accessories such as plugs, flexible wires, ducts,
connectors, extension leads, partholders, electrode-holders, or torches...
Maintenance and repair work on the jackets and insulating ducts must be carried out
extremely carefully.
Have defective parts repaired by a specialist, or better still, have them replaced.
Routinely check the proper tightening and cleanliness of the electric connections.
B) Work-station
Use only electrode holders and torches which are perfectly insulated.
The operator must be insulated from the ground-surface and the workpiece (gloves, safety
shoes, dry clothes, leather apron, and so forth...).
Do not touch the electrode wire and the part (or the nozzle) simultaneously.
C) Protection
It is absolutely essential that your protect your eyes from blinding glare (glare of arc invisible
light and infrared and ultraviolet radiation).
The welding mask, without or with helmet, must always be equipped with a protective filter
whose gradation depends on the welding arc current intensity (EN 169 Standard).
Fumes emitted during welding operations may be dangerous. Use adequate protection
means (fumes extraction, ventiled masks...)
Technical data
TIG manual torch with natural cooling
Safety instructions
French lever rangeErgonomic Range
WTT2 4 m 8 m
20W EB S W000278891 W000278911
EB S
18W EB S W000278895 W000278902
20W
EB C5B W000278892 W000278909
EB C5B
18W
EB C5B W000278896 W000278901
20W EB S/
C5B FLEX W000382786 W000382787
18W EB S/
C5B FLEX W000382788 W000382789
WTT2 20W
WTT2 18W
Instructions for safety, use and maintenance
ES
www.weldline.eu
LINCOLN ELECTRIC EUROPE S.L.
c/o Balmes, 89 - 8o2a- 08008 Barcelona - SPAIN
WTT2 20W 18W
Corrente
assegnata
Factor de marcha 60% 250 A 350 A
Factor de marcha 100% 200 A 320 A
Soldadura de aleaciones ligeras, reducir el factor de marcha un 30%
Caudal agua mín 1.0 l/mn
Presión agua 3.3 bars
Temperatura máxima entrada agua 45°C
Classe de tensión L - 113 V
Caudal de gas Mini : 7 l/mn - Maxi : 13 l/mn
Electrodos utilizables Ø 1.0 / 3.2 mm Ø 1.0 / 4.0 mm
Equipo original
montado en el soplete
Tapón Long Long
Long Long
Boquilla Ø 12 mm Ø 12 mm
Electrodo Ø 2.4 L Ø 2.4 L
WTT2 20W
WTT2 18W
N°8695-1196_Rev2_05/2018
Le agradecemos la confianza que ha depositado en nosotros al adquirir este aparato,
que le dará total satisfacción si respeta sus condiciones de empleo y de mantenimiento.
ATENCIÓN: La sociedad se exime de toda responsabilidad en caso de modificación,
añadido de componentes o de subconjuntos, o de cualquier transformación del
aparato o instalación efectuada por el cliente o por un tercero, sin el acuerdo previo
específico y por escrito de la propia sociedad.
El arco de soldar y la cortadora de plasma pueden ser peligrosos para el operador y
las personas cercanas al area de trabajo. Lea el manual operativo y las instrucciones
de seguridad W000261712. Ver www.weldline.eu.
A) Mantenimiento / Reparación
Antes de cualquier verificación interna o reparación, debe asegurarse de que el aparato
está separado de la instalación eléctrica mediante consignación (se entiende por
consignación, un conjunto de operaciones destinadas a separar y mantener el aparato
fuera de tensión).
Al menos cada 6 meses, debe verificar el correcto estado de aislamiento y las conexiones
de los aparatos y de los accesorios eléctricos como tomas, cables flexibles, conductos,
conectores, prolongadores, pinzas de piezas, portaelectrodos o torchas.Los trabajos de
mantenimiento y de reparación de las cubiertas y conductos aislantes deben realizarse
minuciosamente. Las reparaciones deben ser efectuadas por un especialista, así como
el cambio de las piezas defectuosas.
Verificar periódicamente si el apriete y la limpieza de las conexiones eléctricas son
correctos.
B) Puesto de trabajo
Utilice únicamente portaelectrodos y torchas perfectamente aislados.
El operador debe estar aislado del suelo y de la pieza que va a soldar (guantes, calzado
de seguridad, ropa seca, delantal de cuero, etc.).
No tocar simultáneamente el hilo electrodo (o la boquilla) y la pieza.
C) Seguridad
Es indispensable protegerse los ojos contra los golpes de arco (deslumbramiento del
arco en luz visible y radiaciones infrarroja y ultravioleta).
La mascarilla de soldadura, con o sin casco, siempre debe estar equipada de un
filtro protector, cuya graduación depende de la intensidad de la corriente del arco de
soldadura (Norma EN 169).
Los homos emitidos durante las operaciones de soldatura pueden ser perjudiciales para
la salud. Asegurese de usar equipos de protección adecuados (Mascara con ventilación,
aspiración de humo...)
Datos tecnicos
Torchas manuales TIG refrigeradas por natural
Consignas de seguridad
Instrucciones de seguridad, empleo y mantenimiento
La gama EstándarLa gama Ergonómica
WTT2 4 m 8 m
20W
RL S W000278893 W000278906
RL S
18W
RL S W000278897 W000278900
20W
RL C5B W000278894 W000278905
RL C5B
18W
RL C5B W000278898 W000278899
WTT2 4 m 8 m
20W EB S W000278891 W000278911
EB S
18W EB S W000278895 W000278902
20W
EB C5B W000278892 W000278909
EB C5B
18W
EB C5B W000278896 W000278901
20W EB S/
C5B FLEX W000382786 W000382787
18W EB S/
C5B FLEX W000382788 W000382789
ES