Linde RYVAL 60 PLASMA User manual

Linde AG, Linde Gas Deutschland © RYVAL 60 PLASMA manual EN 06
PLASMA CUTTING MACHINE
RYVAL 60 PLASMA
OPERATING MANUAL

2/20
Linde AG, Linde Gas Deutschland ©
CONTENT
. INTRODUCTION ........................................................................................ 3
2. SAFETY INSTRUCTIONS AND WARNINGS ............................................ 4
3. CONDITIONS OF USE ............................................................................... 7
4. TECHNICAL DATA ..................................................................................... 8
5. MAIN PARTS OF THE MACHINE .............................................................. 9
6. ACCESSORIES ........................................................................................
7. GETTING STARTED ................................................................................ 3
8. CUTTING .................................................................................................. 5
9. MAINTENANCE ........................................................................................ 8
0. STATEMENT OF WARRANTY ................................................................ 9
. DISPOSAL ................................................................................................ 20

3/20
Linde AG, Linde Gas Deutschland ©
1. INTRODUCTION
Congratulations on your new Linde AG, Linde Gas Deutschland product. We are
proud to have you as our customer and will strive to provide you with the best
service and reliability in the industry.
This Operating Manual has been designed to instruct you on the correct use and
operation of your Linde AG, Linde Gas Deutschland product. Your satisfaction
with this product and its safe operation is our ultimate concern. Therefore please
take the time to read the entire manual, especially the Safety Precautions. They
will help you to avoid potential hazards that may exist when working with this
product.
Read and understand this entire Manual and your employer’s safety practices
before installing, operating, or servicing the equipment. While the information
contained in this Manual represents the Manufacturer's best judgement, the
Manufacturer assumes no liability for its use.
Machine RYVAL 60 PLASMA is designed for cutting metal on the basis of
modern technology cutting material through a thin beam plasma gas.
RYVAL 60 PLASMA is designed for high-quality cutting of materials up to 25 mm
thick carbon steel (for more information, see instructions below). Productive
cutting of carbon steel can be to a thickness of 20 mm.
At lower demands on the quality of the cut can be cut through (separate) the
material thickness to 30 mm.

4/20
Linde AG, Linde Gas Deutschland ©
2. SAFETY INSTRUCTIONS AND WARNINGS
. OPERATION AND MAINTENANCE OF PLASMA ARC EQUIPMENT CAN
BE DANGEROUS AND HAZARDOUS TO YOUR HEALTH.
2. Plasma arc cutting produces intense electric and magnetic emissions that
may interfere with the proper function of cardiac pacemakers, hearing aids,
or other electronic health equipment. Persons who work near plasma arc
cutting applications should consult their medical health professional and the
manufacturer of the health equipment to determine whether a hazard exists.
3. Once the packing has been opened, make sure that the machine is not
damaged. If in any doubt, call the service centre.
4. This equipment must only be used by qualified personnel.
5. During installation, any electric work must only be carried out by trained
personnel.
6. The machine must be used in a dry place with good ventilation.
7. Make sure that no metal dust can be drawn in by the fan inside the machine,
as this could cause damage to the electronic circuits.
8. It is prohibited to connect more than one INVERTER generator in series or in
parallel.
9. When installing the machine, follow the local regulations on safety.
0. The position of the machine must allow easy access by the operator to the
controls and connectors.
. When the cutting machine is operating, all its covers and doors must be
closed and well fixed.
2. Do not expose the cutting machine to direct sunlight or to heavy rain. This
equipment conforms to protection rating IP 23S.
3. The operator must wear gloves, clothes, shoes, and a helmet or a welder’s
helmet, which protect and are fire-resistant in order to protect him against
electric shock, flashes and sparks from cutting.
4. The operator must protect his eyes with safety visor or mask designed for
welding, fitted with standard safety filters. He should also be aware that during
plasma cutting ULTRAVIOLET RADIATION is emitted. Therefore it is vital
that his face is also protected from radiation. Ultraviolet rays produce the
same harmful effect as sun burning on unprotected skin.
5. The operator is obliged to warn anyone near the cutting area of the risks
that cutting involves and to arrange to provide adequate protection
equipment.
6. Keep all fumes and gases from the breathing area.
7. Keep your head out of the fume plume.
8. Use an air-supplied respirator if ventilation is not adequate to remove all
fumes and gases.
9. The kinds of fumes and gases from the plasma arc depend on the kind of
metal being used, coatings on the metal, and the different processes. You
must be very careful when cutting or welding any metals which may contain

5/20
Linde AG, Linde Gas Deutschland ©
one or more of the following:
Antimony
Chromium
Mercury
Nickel
Cobalt
Arsenic
Barium
Copper
Selenium
Beryllium
Lead
Silver
Cadmium
Manganese
Vanadium
20. Always read the Material Safety Data Sheets (MSDS) that should be
supplied with the material you are using. These MSDSs will give you the
information regarding the kind and amount of fumes and gases that may be
dangerous to your health.
2 . It is very important to arrange for sufficient ventilation, especially when
cutting in enclosed spaces. We suggest using suitable fume extractors to
prevent the risk of intoxication by fumes or gas generated by the cutting
process.
22. Noise can cause permanent hearing loss. Plasma arc processes can
cause noise levels to exceed safe limits. You must protect your ears from loud
noise to prevent permanent loss of hearing.
23. To protect your hearing from loud noise, wear protective ear plugs and/or
ear muffs. Protect others in the workplace.
24. Noise levels should be measured to be sure the decibels (sound) do not
exceed safe levels.
25. The operator must ensure all flammable materials are removed from the
work area to avoid any risk of fire.
26. The operator must NEVER cut containers that have previously contained
petrol, lubricants, gas or similar flammable materials, even if the container
has been empty for a considerable time. THERE IS A VERY HIGH RISK OF
EXPLOSION.
27. The operator must be aware of all the special regulations which he needs
to conform to when cutting in enclosed spaces with a high risk of explosion.
28. To prevent electric shock, we strongly suggest the following rules:
a) Do not work in a damp or humid environment.
b) Do not use the machine if its cables are damaged in any way.
c) Make sure that the earthing system of the electric equipment is correctly
connected and operational.
d) The operator must be insulated from the metal components connected
to the return wire.
e) The earthing of the piece being worked could increase the risk of injury
to the operator.
29. EN 60974- Standard: Open-circuit voltage. During the operation of the
machine, the highest voltage, with which it is possible to come into contact, is
the open-circuit voltage between the clamps. In our generator this voltage is
3 0V.
30. The maximum open-circuit voltage of the plasma machines is established
by national and international standards (EN 60974- ) depending on the type

6/20
Linde AG, Linde Gas Deutschland ©
of current to be used, on its waveform and on the hazards arising from the
work place. These values are not applicable to the strike currents and those
for stabilisation of the arc that could be above it.
3 . The open-circuit voltage, for as many adjustments as possible, must never
exceed the values relating to the various cases shown in the following table:
Case
Working conditions
Open
-
circuit voltage
Places with increased risk of
electric shock
DC current: 3V
peak value
AC current: 68V
peak value and
4
8V effective
2 Places without increased risk
of electric shock
DC current: 3V
peak value
AC current: 3V
peak value and
80V effective
3
Torches held mechanically
with increased protection for
the operator
DC current: 4 V
peak value
AC current: 4 V
peak value and
00V effective
4 Plasma cutting DC current: 500V
peak
value
32. In case , the dc machines with rectifier must be built in such a way that,
in case of a fault developing in the rectifier (for example open circuit, short
circuit or lack of power), the permitted values cannot be exceeded. The
plasma cutting machines of this type can be marked with the symbol:
S
33. Before opening the machine switch off the machine and disconnect it from
the power socket.
34. Only personnel authorised by this company can carry out maintenance on
the machine.
PROTECTIVE UTTILITIES
. Welding helmet with filter shade at least 0
2. Welding gloves
3. Welding apron and cloth
4. Welding boots
RISK OVERVIEW
. Risk of electric shock.
2. Ultraviolet light and light radiation
3. Risk of inhaling gas fumes and dust particles
4. Burns
5. Noise

7/20
Linde AG, Linde Gas Deutschland ©
NOTE
The Mach ne Torches (AUT) must not be used w th RYVAL 60 PLASMA. It
may only be used together w th RYVAL 60 PLASMA CNC.
NOTE
. It is forbidden to operate a machine with damaged insulation of the cutting
torch or supply cable.
2. Never operate the machine taken down or damaged covers.
3. It is forbidden to operate the machine in wet environments and outdoors in
rain or snow.
4. Ensure proper grounding clamping pliers, which also reduces the risk of
electric shock.
5. Use prescribed protective utilities, keep them dry.
6. Plasma arc cutting produces intense electric and magnetic emissions that
may interfere with the proper function of cardiac pacemakers, hearing aids,
or other electronic health equipment. Persons who work near plasma arc
cutting applications should consult their medical health professional and
the manufacturer of the health equipment to determine whether a hazard
exists.
7. Never aim the torch against the eyes, body or other person.
3. CONDITIONS OF USE
. This equipment must only be used by qualified personnel.
2. Device complies with IEC 6 000-3- 2 with following conditions:
Short-circuit power Ssc of network in place at an interface between the user's
supply and the public network (PCC) must be least 356 kW.
User is obliged to consult with the electricity supplier if the impedance of the
network at this point is that required short-circuit capacity Zmax = 45 mΩ and
whether the device can be connected with a public low-voltage network.
On the nameplate are the following symbols: .
3. During installation, any electric work must only be carried out by trained
personnel.
4. Working ambient temperature between - 0 and +40 °C.
5. Relative humidity below 90% at +20 °C.
6. Up to 3000 m altitude.
7. Do not expose the plasma machine to direct sunlight or to rain or snow. This
equipment conforms to protection rating IP23S.
8. Place the machine the way that the cooling air can enter the vents without
restriction to. It is necessary to ensure that no impurities, especially metal
particles, are not drawn into the machine.
9. Cutting machine in terms of interference suppression is intended primarily for
industrial premises. In the case of use of other areas may be need for special

8/20
Linde AG, Linde Gas Deutschland ©
measures (see EN 60974- 0).
0. The machine must be protected against
a) Moisture and rain and snow
b) Mechanical damage
c) Draft and any ventilation of neighbouring machine
d) Excessive overloading - crossing technical parameters
e) Rough handling
ELECTROMAGNETIC COMPATIBILITY
The welding device is in terms of interference designed primarily for industrial
areas. It meets the requirements of EN 60974- 0 class A and it isn’t designed
for using in residential areas, where the electrical energy is supplied by public
low-voltage power supply network. It can be here potential problems with
ensuring of electromagnetic compatibility in this areas, due to interference
caused by power lines as well as the radiated interference.
During operation, the device may be the source of interference.
Caution We warn users, that they are responsible for possible
interference from welding.
4. TECHNICAL DATA
RYVAL 60 PLASMA
Method Plasma cutting
Mains voltage V/Hz 3 x 400/50-60
Mains protection A 20 - 65
Max. effective current I eff A 3 0
Cutting current range A 6 @
Open-circuit voltage U20 V 5,6
Cutting current (DZ= 00%) I2 A 60
Cutting current (DZ=60%) I2 A 65
Cutting current (DZ=90%) I2 A 90%=65
Max. productive cutting thickness – carbon steel mm 20
Max. cutting thickness – carbon steel mm 30
Quality cutting thickness
Carbon steel 25 25
Stainless steel 8 8
Aluminium 5 5
Copper 0 0
Working pressure bar 8,5

9/20
Linde AG, Linde Gas Deutschland ©
Max. input pressure bar 5,0 – 5,5
Air consumption l/min 240
Arc ignition pneu-mechanic
Current regulation continuous
Protection IP 23 S
Standards EN 60974- , EN 60974- 0 cl. A
Dimensions (w x l x h) mm 240 x 440 x 595
Weight kg 24,0
5. MAIN PARTS OF THE MACHINE
FRONT AND REAR PANELS
Picture – The main parts
Pos.
Descr pt on
A
Quick connector
-
earthing cable
A2 Connector - remote control – in standard doesn’t work – only on
request
A3
Connector
-
torch
A4
Potenciometer
-
set cut current

0/20
Linde AG, Linde Gas Deutschland ©
A5
LED
indicator
–
when illuminated, the machine is ON.
A6 LED indicator-overheating
when illuminated, please leave the machine turned on and wait on
cooling the machine
down
.
A7 . LED indicator flashes – the Retaining Cup isn’t on or is fitted
badly
2.
LED
indicator shines
–
low gas pressure
A8 LED indicator – arc burning – after you press the torch button,
it shines, on the torch is a voltage
A9
Switch
Setting of gas flow
Continuous cutting
Cutting material with gaps – Caution! Higher wear of nozzles
and electrodes
A 0
Manometer
A
Gas fitting
A 2
Controler
A 3
Mains cable
A 4
Switch ON/OFF

/20
Linde AG, Linde Gas Deutschland ©
6. ACCESSORIES
PART OF DELIVERY
Pos.
Code
Description
Earthing cable PEGAS 60 3 m
Picture 2 – Torch SVH- 05 – parts
ON REGUEST
P
os.
Code
Description
5872 Bevel Tolls for PT 40, 60, SCP 60, TH-70, 25
5302
Air Filter AT 000
5304
Adapter for AT 000 PEGAS PLASMA
S777
c.
Welding Helmet Barracuda S777C Black
7
037
Torch Plasma SVH
-
05 hand 75°
7
042
Cable Package 6,0 m SV
-
25 6 PIN
7 0 Silicone Lubricant Brutto 6 g
7 02
Silicone Lubricant Brutto
9
g

2/20
Linde AG, Linde Gas Deutschland ©
7 2 Set START to the torch SVH- 05
(
Recommended START set for the torch
–
Pic. 2
)
Quantity
8 5832 Tip 20-50A STM-70, TM-70,
TM
-
05, SVH
-
05
(pkg. 0)
2
8 700 Tip 05A TM- 05, SVH/SVM- 05
(pkg. 0)
2
7 5937 Tip 70A TM-70, TM- 05, SVH- 05
(pkg. 0) 2
7 7000 Tip TM- 05, SVH/SVM- 05
(pkg. 0)
5
5 5830 Electrode STM-70, TM-70,
TM
-
05, SVH/SVM
-
05 (pkg. 0)
0
7072
Shield Cup 85
-
05A SVH
-
05
9 707 Shield Cup body 80- 05A
SVH/SVM
-
05
5 6998 Swirl Ring 85- 05A TM- 05,
SVH
-
05 eco
(
pkg.2)
Parts of the torch
(Pic. 2)
5790 O-Ring TM-70, TM- 05, TM- 25, SVH/
SVM
-
05
(pkg.2)
3 5830 Electrode STM-70, TM-70, TM-105,
SVH/SVM
-
105 (pkg.10)
4 5936 Swirl Ring TM-70, TM- 05, SVH- 05 eco
(pkg.2)
4 583 Swirl Ring STM-70, TM-70, TM- 05, SVH- 05
Maximum Life
(pkg.2)
5 6998 Sw rl R ng 85-105A TM-105, SVH-105 eco
(pkg.2)
5 6999 Swirl Ring 85- 05A TM- 05, SVH- 05 Life
(pkg.2)
6 5832 Tip 20-50A STM-70, TM-70, TM- 05,
SVH
-
05
(pkg. 0)
6
5937
Tip 70A TM
-
70,
TM
-
05, SVH
-
05
(pkg. 0)
7
7000
Tip TM
-
05,
SVH/SVM
-
05
(pkg. 0)
7
7001
T p 105A TM
-
105, SVH/SVM
-
105 (pkg.10)
8
7070
Shield Cup body 20
-
70A SVH
-
05
9
7071
Sh eld Cup body 80
-
105A SVH/SVM
-
105
0
7073
Shield Cup 20
-
70A SVH
-
05
11
7072
Sh eld Cup 85
-
105A SVH
-
105
2
7074
Tip gouging 45A
SVH
-
05 (pkg. 0)
2
7075
Tip gouging 70A SVH
-
05 (pkg. 0)
7
7000
Tip TM
-
05, SVH/SVM
-
05
(pkg. 0)
7
700
Tip 05A TM
-
05, SVH/SVM
-
05
(pkg. 0)

3/20
Linde AG, Linde Gas Deutschland ©
8
7 07
Shield Cup extended 20
-
70A SVH
-
05
9
7 08
Shield Cup extended 85
-
05A SVH
-
05
Note – the bold items are equipped on the torch
7. GETTING STARTED
TORCH CONNECTION SCHEMA
Getting started must be consistent with technical data and conditions of use
(especially with 2. point).
FIRST STEPS
 NOTE  This equipment must only be used by qualified personnel.
. Before beginning work is necessary to connect the machine to the mains.
2. Check completeness of the mounted cutting torch.
3. Connect the torch to the connector. By means of the thorn (part of the
delivery) press the safety pin. Turn the nut of the connecter clock wise and
tight it properly.
4. Connect the mains cable A13 to the on the network according 4 TECHNICAL
DATA.
5. Connect the compressed air on connector A11 on the rear wall of the
machine.
6. Set the air pressure by means of regulator A12 and manometer A10 to 5 bars.
7. Connect the mains plug to the mains socket.
8. After turning on the ON/OFF switch A14 the display A5 will illuminate.
9. Connect the work lead cable to the material being cut and to the
connector A1.
PIN
NO. TORCH
Trigger
2 Trigger
3 /
4 /
5 Pilot arc
6 Pilot arc
7 /
8 Safety
9 Safety

4/20
Linde AG, Linde Gas Deutschland ©
0. Check up the input air pressure (min 5 bar, max 8,5 bar) and make a
regulation if necessary.
. Set potentiometer A4 to the cutting power you need.
2. Fit the torch with appropriate type of cutting tip electrode and shield cup
according to the selected cutting current.
3. Press the trigger on the cutting torch, the pre gas will flow for s.
4. The pilot arc will start.
5. Shift the torch with the pilot arc close to the material, the pilot arc will
change to cutting arc automatically. If you do not start cutting within 2 s,
the arc will snuff off. If the torch delays during the cutting from the material,
the arc will snuff off. In case that the machine is in mode Cutting material
with gaps – switch A9 position , cutting arc will change to pilot arc and
if you do not start cutting within 2 s, this arc will snuff off.
6. To finish the cutting process, release the torch trigger.
REQUIREMENTS FOR SOURCE OF COMPRESSED AIR
. Delivered air pressure must be max. 8,5 bar and min. 5 bar.
2. Air consumption minimal 260 l/min
3. Compressed air for the plasma must be clean and dry.
4. Pressure dew point +3 °C
5. Maximum oil content 0. mg/m3
6. Maximal size of solid particles 5 microns
7. The minimal size of an air tank is 50 l
8. No additional oiling if the pressure air is permitted. That could damage the
plasma machine and the cutting torch.
OPTIONAL AIR FILTERS
To achieve high quality cutting and to avoid serious disturbances to the torch it
is highly advised to include the air filter.
Pos. Item No Description
24
5302 Air filter AT 000
25
5304 Set for filter AT 000 to RYVAL Plasma
NOTE Max. allowable pressure of filter AT 000 is 8,5 bar.

5/20
Linde AG, Linde Gas Deutschland ©
Picture 3 – Air filter
8. CUTTING
The table below shows just referential values. The real values may change
according the material qualities. The darker colour highlights heat area where
the consumables are more worn off.
S 05 Carbon steel – material thickness and recommended cutting
tips
Cutting
current
2 4 6 8 0 2 4 6 8 20 22 24 26 28 30 Tip
50 A
4546
( ,0)
70 A
4547
( ,2)
00 A
4548
( ,4)
. Press the torch trigger. The pilot arc will ignite. Then you have to immediately
attach the torch to the cut material. At this point begins to burn the main arc
between the torch and the material.
2. Move the torch with a constant speed. Cutting speeds vary according to torch
output amperage, the type of material being cut, and operator skill.
3. Output current setting or cutting speeds may be reduced to allow slower
cutting when following a line, or using a template or cutting guide while still
producing cuts of excellent quality.
4. To achieve a good cutting quality make sure the distance between the tip and

6/20
Linde AG, Linde Gas Deutschland ©
the material is about 3,5 mm. The Stand Off Guide located at the end of the
plasma torch guarantees the distance. At a greater distance decreases
cutting power and the arc may go off. With too small distance the torch parts
will be worn off faster.
5. Plasma cutting may be done in all possible positions (vertically, horizontally,
overhead, vertical ascending and descending), but as far as possible choose
primarily horizontal cut. In other positions the operator is increasingly
threatened by flying drops of molten material.
6. We recommend starting cutting at the edge of the material. If needed to start
from the centre of the material, or to cut hole into the material, slightly tilt the
torch head and gradually it straighten into a vertical position so the spraying
material would not damage the cutting tip (see Pic. 4). This workflow must
always be followed, if the thickness of material is above above 3 mm.
7. In case of cutting in the corner or around the corner (see Pic. 5), use the long
electrode and cutting tip. The cutting power while using the Long cutting tip is
decreased.
Picture 4 - Cutting Picture 5 - Cutting
IMPORTANT RULES
. The pilot arc burning time should be limited only to the time necessary. It
lowers the wear of the cutting tips and electrodes.
2. Never turn off the main switch immediately after finishing cutting but always
leave time to run cooling cycle to cool down the torch. Immediate turn-off only
in case of emergency.
3. Ensure a good el. Contact of the work lead clamps and cutting material.
4. Check and timely exchange cutting tips and the electrodes. Lifetime of these
parts is only a few hours of cutting time and is highly dependent on
compliance with the principles of good cutting.
5. Disconnect the machine from the mains before replacing the torch
consumable parts.
6. Unplug the machine from the mains before any intervention inside the
machine.
7. RYVAL 60 PLASMA is adapted for use with torch Plasma SVH- 05. This
combination comply with EN 60974-7 Article 0. .4. Using any other type
and design of a torch must be approved by Linde AG, Linde Gas

7/20
Linde AG, Linde Gas Deutschland ©
Deutschland.
8. Imperfect capture of condensate would cause its elimination in the area of the
cutting tip and it would prevent ignition of the pilot arc.
SOURCES OF POOR QUALITY CUTS
Shallow penetrat on of the cut
. The cutting speed is too high. Make sure the slope of the cutting arc does not
exceed about 5 ° (see Pic. 6).
2. High wear of the cutting tip or electrode (see Pic. 7).
3. Too large thickness of material and not adequately chosen value of current
and diameter of the cutting tip.
4. Bad contact between the work lead clamps and material.
Cutt ng arc s unstable, goes off and "shoots"
. Worn out cutting tip or electrode
2. High pressure
3. Impurities in the pressure air
4. Not captured water condensate
Con cal cut
. If there is a false cut (see Pic. 8) turn off the machine, release the shield cup
and rotate the cutting tip about /4 and again try to cut.
2. Damaged cutting tip and electrode
3. The position of the torch is not perpendicular to the material.
4. Too large distance from the cutting tip to the material.
Max 5
o
Picture 6 Picture 7 Picture 8

8/20
Linde AG, Linde Gas Deutschland ©
9. MAINTENANCE
. A great care should be taken to the cutting torch. The molten material sprays
while cutting. This sputter contaminates the interior space of the torch. The
worn parts (consumables) of a plasma torch should be regularly maintained
and timely exchanged. Regularly check the condition of diffuser channels
(see diagram of the torch). If contaminated, you must clean it with a pressure
air or to replace the diffuser. Poor state of the diffuser has a negative impact
on the quality of cutting and causes very strong interference that may cause
the collapse of the machine control electronics or influence the surrounding
devices. If the cable bundle of the torch is worn out it must be replaced
immediately - danger of electrical shock.
2. Disconnect the RYVAL from the mains supply voltage before disassembling.
3. Special maintenance is not necessary for the control unit parts in the plasma
cut machine. If these parts are damaged for any reason, replacement is
recommended.
CAUTION 
4. Do not blow air into the plasma cut during cleaning. Blowing air into the
plasma cut can cause metal particles to interfere with sensitive electronic
components and cause damage to the welder.
5. To clean the plasma cut, disconnect it from the mains supply voltage then
open the enclosure and use a vacuum cleaner to remove any accumulated
dirt and dust. The plasma cut should also be wiped clean. If necessary,
solvents that are recommended for cleaning electrical apparatus may be
used.
6. Troubleshooting and repairing of RYVAL equipment should only be carried
out only by suitably qualified or competent person.
7. A ‘competent person’ must be a person who has acquired through training,
qualification or experience, or a combination of them, the knowledge and
skills enabling that person to safely carry out a risk assessment and repairs
to the electrical equipment in question.
8. The person carrying out the servicing needs and repairs must know what to
look at, what to look for and what to do.

9/20
Linde AG, Linde Gas Deutschland ©
LUBRICATION OF THE ELECTRODE HOLDER WITH THE
SILICONE LUBRCANT
Picture 9 - Lubrication of the electrode holder
Lubr cat on procedure:
. Remove the retaining cap, cutting tip and swirl ring; keep the electrode in
the electrode holder.
2. Lubricate the electrode holder with the silicone lubricant, as shown in the
pictures above (ordering numbers of lubricants you can find in Accessories
on request).
3. Then push the electrode up and down for 0-20 times for thorough
lubrication.
4. Remove the excess silicone lubricant before putting the torch back
together.
Lubr cat on must be performed n the follow ng cases:
. If is any difficulty in the movement of the electrode holder.
2. After the period of the prolonged inactivity.
Note: Thoroughly clean the electrode holder before lubricating it!
10. STATEMENT OF WARRANTY
. In accordance with the warranty periods stated below, Linde AG, Linde Gas
Deutschland guarantees the proposed product to be free from defects in
material or workmanship when operated in accordance with the written
instructions as defined in this operating manual.
2. Linde AG, Linde Gas Deutschland products are manufactured for use by
commercial and industrial users and trained personnel with experience in the
use and maintenance of electrical welding and cutting equipment.
3. Linde AG, Linde Gas Deutschland will repair or replace, at its discretion, any
warranted parts or components that fail due to defects in material or
workmanship within the warranty period. The warranty period begins on the
date of sale to the end user.

20/20
Linde AG, Linde Gas Deutschland ©
4. If warranty is being sought, please contact your Linde AG, Linde Gas
Deutschland product supplier for the warranty repair procedure.
5. Linde AG, Linde Gas Deutschland warranty will not apply to:
a) Equipment that has been modified by any other party other than Linde
AG, Linde Gas Deutschland’s own service personnel or with prior
written consent obtained from Linde AG, Linde Gas Deutschland
Service Department.
b) Equipment that has been used beyond the specifications established in
the operating manual.
c) Installation not in accordance with the installation/operating manual.
d) Any product that has been subjected to abuse, misuse, negligence or
accident.
e) Failure to clean and maintain (including lack of lubrication, maintenance
and protection), the machine as set forth in the operating, installation or
service manual.
6. Within this operating manual are details regarding the maintenance
necessary to ensure trouble free operation.
7. Validity condition of warranty is, that the cutting machine must be used only
with the torch, which is said in this manual.
NOTE 
Warranty repairs must be performed by either a Linde AG, Linde Gas
Deutschland Service Centre, an Linde AG, Linde Gas Deutschland distributor or
an Authorised Service Agent approved by the company Linde AG, Linde Gas
Deutschland.
11. DISPOSAL
Only for EU countries. Do not dispose of electric tools together
with household waste material.
In accordance with European Council Directive 2002/96/EC on
electrical and electronic equipment waste and its
implementation in accordance with national law, electric tools
that have reached the end of their service life must be collected
separately and returned to an environmentally compatible
recycling facility.