Linear Technology LTM4676EY User manual

1
dc1989abf
DEMO MANUAL DC1989A-B
Description
LTM4676EY
Dual 13A or Single 26A µModule Regulator
with Digital Power System Management
Demonstration circuit 1989A-B is a high efficiency, high
density, µModule regulator with 4.5V to 16V input range.
The output voltage is adjustable from 0.5V to 4V, and it can
supply 75A maximum load current. The demo board has
three LT M
®
4676 µModule regulators, and the LTM4676 is
a dual 13A or single 26A step-down regulator with PMBus
power system management. Please see LTM4676 data
sheet for more detailed information
DC1989A-B powers up to default settings and produces
power based on configuration resistors without the need
for any serial bus communication. This allows easy evalu-
ation of the DC/DC converter. To fully explore the extensive
power system management features of the part, download
the GUI software LTpowerPlay™ onto your PC and use
LT C ’s I2C/SMBus/PMBus dongle DC1613A to connect to
L, LT, LTC, LTM, Linear Technology, the Linear logo, Dust Networks and Dust are registered
trademarks and LTpowerPlay is a trademark of Linear Technology Corporation. All other
trademarks are the property of their respective owners.
the board. LTpowerPlay allows the user to reconfigure the
part on the fly and store the configuration in EEPROM, view
telemetry of voltage, current, temperature and fault status
GUI Download
The software can be downloaded from:
http://www.linear.com/ltpowerplay
For more details and instructions of LTpowerPlay, please
refer to LTpowerPlay GUI for LTM4676 Quick Start Guide.
Design files for this circuit board are available at
http://www.linear.com/demo/DC1989A-B
Figure 1. LTM4676/DC1989A-B Demo Circuit
This datasheet has been downloaded fromhttp://www.digchip.com at this page

2
dc1989abf
DEMO MANUAL DC1989A-B
Quick start proceDure
Demonstration circuit 1989A-B is easy to set up to evalu-
ate the performance of the LTM4676EY. Refer to Figure 2
for the proper measurement equipment setup and follow
the procedure below.
1. With power off, connect the input power supply to VIN
(4.5V to 16V) and GND (input return).
2. Connect the 1V output load between VOUT0 and GND
(Initial load: no load).
3. Connect the DVMs to the input and outputs. Set default
switch position: SW1: ON; SW2: ON.
4. Turn on the input power supply and check for the proper
output voltages. VOUT0 should be 1V ±1%.
5. Once the proper output voltages are established, ad-
just the loads within the operating range and observe
the output voltage regulation, ripple voltage and other
parameters.
6. Connect the dongle and control the output voltages
from the GUI. See “LTpowerPlay GUI for the LTM4676
Quick Start Guide” for details.
Note: When measuring the output or input voltage ripple,
do not use the long ground lead on the oscilloscope probe.
See Figure 3 for the proper scope probe technique. Short,
stiff leads need to be soldered to the (+) and (–) terminals
of an output capacitor. The probe’s ground ring needs to
touch the (–) lead and the probe tip needs to touch the
(+) lead.
Connecting a PC to DC1989A-B
You can use a PC to reconfigure the power management
features of the LTM4676 such as: nominal VOUT, margin
setpoints,OV/UVlimits,temperaturefaultlimits,sequenc-
ing parameters, the fault log, fault responses, GPIOs and
other functionality. The DC1613A dongle may be plugged
when VIN is present.
performance summary
Specifications are at TA= 25°C
PARAMETER CONDITION VALUE
Input Voltage Range 4.5V to 16V
Output Voltage, VOUT0 VIN = 4.5 to 16V, IOUT0 = 0A to 75A 0.5V to 4V, Default: 1V
Maximum Output Current, IOUT0 VIN = 4.5 to 16V, VOUT = 0.5V to 4V 75A
Typical Efficiency VIN = 12V, VOUT = 1V, IOUT = 75A 80%
Default Switching Frequency 350kHz
Table 1. LTM4676 Demo Cards for Up to 130A Point-of-Load Regulation
MAXIMUM OUTPUT CURRENT NUMBER OF OUTPUT VOLTAGES
NUMBER OF LTM4676 µMODULE
REGULATORS ON THE BOARD DEMO BOARD NUMBER
13A, 13A 2 1 DC1811A
26A 1 1 DC2087A
50A 1 2 DC1989A-B
75A 1 3 DC1989A-B
100A 1 4 DC1989A-C
100A 1 1 (+ 3x LTM4620A) DC2106A-A
130A 1 1 (+ 3x LTM4630) DC2106A-B

3
dc1989abf
DEMO MANUAL DC1989A-B
Quick start proceDure
Figure 2. Proper Measurement Equipment Setup
Figure 3. Measuring Output Voltage Ripple

4
dc1989abf
DEMO MANUAL DC1989A-B
Quick start proceDure
Figure 4. Demo Setup with PC
Figure 5. Efficiency vs Load Current at VIN = 5V and VIN = 12V
Efficiency vs Load Current
100
90
70
80
60
50
LOAD CURRENT (A)
EFFICIENCY (%)
0
75
5 15 45 55 653525
VIN = 5V
VIN = 12V
VOUT0 = 1V

5
dc1989abf
DEMO MANUAL DC1989A-B
Quick start proceDure
Figure 8. Thermal Performance at VIN = 12V, VOUT0 = 1V, IOUT0 = 75A, TA= 23.8°C, Air Flow 200LFM
VOUT0 (20MHz BW) [50mV/DIV]
37.5A TO 75A LOAD STEP
VOUT0 (20MHz BW) [10mV/DIV]
Figure 6. Output Voltage VOUT0 vs Load Current
(VOUT0 RANGE = 0)
Figure 9. Current Sharing at VIN = 12V, VOUT0 = 1V
(Based on the Current Readback)
Figure 7. Output Voltage Ripple at VIN = 12V,
VOUT0 = 1V, IOUT0 = 75A
Figure 10. Total Current Readback vs Load
Current at VIN = 12V, VOUT0 = 1V
0 10 20 30
75
50405 15 25 45 60 65 705535
LOAD CURRENT (A)
PHASE CURRENT (A)
14
12
8
10
6
2
4
0
–2
IOUT_PHASE#1
IOUT_PHASE#2
IOUT_PHASE#3
IOUT_PHASE#4
IOUT_PHASE#5
IOUT_PHASE#6
LOAD CURRENT (A)
0
TOTAL CURRENT READBACK (A)
80
50
40
70
60
30
10
20
010 20 30
75
50405 15 25 45 60 65 705535

6
dc1989abf
DEMO MANUAL DC1989A-B
Quick start proceDure
LTpowerPlay Software GUI
LTpowerPlay is a powerful Windows based development
environment that supports Linear Technology power sys-
tem management ICs, including the LTM4676, LTC3880,
LTC3883, LTC2974 and LTC2978. The software supports
a variety of different tasks. You can use LTpowerPlay to
evaluate Linear Technology ICs by connecting to a demo
board system. LTpowerPlay can also be used in an offline
mode (with no hardware present) in order to build a mul-
tichip configuration file that can be saved and reloaded at a
latertime.LTpowerPlayprovidesunprecedented diagnostic
and debug features. It becomes a valuable diagnostic tool
during board bring-up to program or tweak the power
management scheme in a system, or to diagnose power
issues when bringing up rails. LTpowerPlay utilizes the
DC1613A USB-to-SMBus controller to communicate with
one of many potential targets, including the LTM4676, the
LTC3880 and the LTC3883’s demo system, or a customer
board. The software also provides an automatic update
feature to keep the software current with the latest set
of device drivers and documentation. The LTpowerPlay
software can be downloaded from:
http://linear.com/ltpowerplay
To access technical support documents for LT C Digital
Power Products visit Help. View online help on the
LTpowerPlay menu.
LTpowerPlay QUICK START PROCEDURE
Thefollowing procedure describeshow to use LTpowerPlay
to monitor and change the settings of LTM4676.
1. Download and install the LTPowerPlay GUI:
http://linear.com/ltpowerplay
Figure 11. LTpowerPlay Main Interface

7
dc1989abf
DEMO MANUAL DC1989A-B
Quick start proceDure
2. Launch the LTpowerPlay GUI.
a. The GUI should automatically identify the DC1989A-B.
The system tree on the left hand side should look like
this:
b. A green message box shows for a few seconds in the
lower left hand corner, confirming that LTM4676 is
communicating:
c. In the Toolbar, click the “R” (RAM to PC) icon to read the
RAM from the LTM4676. This reads the configuration
from the RAM of LTM4676 and loads it into the GUI.
d. If you want to change the output voltage to a different
value, like 1.5V. In the Config tab, type in 1.5 in the
VOUT_COMMAND box, like this:
Then, click the “W” (PC to RAM) icon to write these
register values to the LTM4676. After finishing this step,
you will see the output voltage will change to 1.5V.
If the write is successful, you will see the following
message:
e. You can save the changes into the NVM. In the tool bar,
click “RAM to NVM” button, as following
f. Save the demo board configuration to a (*.proj) file. Click
the Save icon and save the file. Name it whatever you want.

8
dc1989abf
DEMO MANUAL DC1989A-B
parts List
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER
Required Circuit Components
1 14 CIN1, CIN2, CIN4-CIN15 CAP., X5R, 10µF, 35V, 10%, 1210 AVX, 1210DD106KAT2A
2 1 CIN3 CAP., 150µF, 35V, ALUMINUM ELECTR., SUN ELECT., 35CE150AX
3 10 COUT1, COUT6, COUT7, COUT9, COUT12, COUT17,
COUT18, COUT20, COUT23, COUT27
CAP., X5R, 100µF, 6.3V, 20% 1210 AVX, 12106D107KAT2A
4 1 C3 CAP., X5R, 220pF, 16V, 10%, 0603 AVX, 0603YD221KAT2A
5 8 COUT4, COUT5, COUT8, COUT15, COUT16,
COUT19, COUT26, COUT28
CAP., 330µF, 6.3V, POSCAP, D3L SANYO, 6TPF330M9L
6 1 C7 CAP., X7R, 470pF, 16V, 10%, 0603 AVX, 0603YC471KAT2A
7 1 C4 CAP., X7R, 3.3nF, 16V, 10%, 0603 (3300pF) AVX, 0603YC332KAT2A
8 2 C5, C12 CAP., X5R, 10nF, 16V, 10%, 0603 (0.01µF) AVX, 0603YD103KAT2A
9 1 C21 CAP., X5R, 100nF, 16V, 10%, 0603 (0.1µF) AVX, 0603YD104KAT2A
10 1 C70 CAP., X5R, 1µF, 25V, 10%, 0805 AVX, 08053D105KAT2A
11 2 C65, C68 CAP., X5R, 1µF, 25V, 10%, 1206 AVX, 12063D105KAT2A
12 1 C67 CAP., X7R, 0.1µF, 25V, 10%, 1206 AVX, 12063C104KAT2A
13 1 C64 CAP., X5R, 4.7µF, 25V, 10%, 0603 MURATA, GRM188R61E475KE11
14 1 C66 CAP., X5R, 0.22µF, 25V, 10%, 0805 AVX, 08053D224KAT2A
15 1 C69 CAP., X7R, 150pF, 25V, 10%, 0603 AVX, 06033C151KAT2A
16 2 D1, D2 LED GREEN S-GW TYPE SMD PANASONIC LN1371SGTRP
17 1 D3 LED RED S-TYPE GULL WING SMD PANASONIC LN1271RTR
18 1 J7 CONN HEADER 12POS 2MM STR DL PCB FCI 98414-G06-12ULF
19 1 J8 PIN HEADER 20 DUAL ROW RA (M) Mill Max 802-40-020-20-0001
20 1 J9 CONN SOCKET 20 DUAL ROW RA (F) Mill Max 803-43-020-20-001
21 2 J10, J11 CONN, BNC, 5 PINS CONNEX, 112404
22 1 Q1 MOSFET P-CH 20V 0.58A SOT-23 VISHAY TP0101K-T1-E3
23 2 Q2, Q3 MOSFET N-CH 60V 115mA SOT-23 FAIRCHILD 2N7002K
24 2 Q11, Q12 N-CHANNEL 30-V MOSFET, TO-252 VISHAY, SUD50N03-09P-E3
25 1 R20 RES., CHIP, 22.6k, 1%, 0603 VISHAY CRCW060322K6FKEA
26 25 R2, R4, R18, R25, R26, R120-R122, R30, R32, R47,
R48, R50, R56, R58, R60, R72, R74, R85, R86,
R89, R90, R92, R104, R119
RES., CHIP, 0Ω, 1%, 0603 VISHAY CRCW06030000Z0EA
27 4 R49, R51, R53, R54 RES., CHIP, 0Ω, 1%, 2010 VISHAY CRCW20100000Z0EA
28 16 R6, R7, R8, R9, R10, R11, R12, R15, R35, R36,
R39, R64, R78, R97, R98, R116
RES., CHIP, 10k, 1%, 0603 VISHAY CRCW060310K0FKEA
29 1 R27 RES., CHIP, 51k, 1%, 0603 VISHAY CRCW060351K0FKEA
30 1 R14 RES., CHIP, 2k, 1%, 0603 VISHAY CRCW06032K0FKEA
31 2 R16, R41 RES., CHIP, 10Ω, 1%, 0603 VISHAY CRCW060310R0FKEA
32 1 R112 RES., CHIP, 100Ω, 1%, 0603 VISHAY CRCW0603100RFKEA
33 1 R113 RES., CHIP, 1.4k, 1%, 0603 VISHAY CRCW06031K40FKEA
34 1 R19 RES., CHIP, 787Ω, 1%, 0603 VISHAY CRCW0603787RFKEA
35 1 R40 RES., CHIP, 1.65k, 1%, 0603 VISHAY CRCW06031K65FKEA
36 1 R42 RES., CHIP, 3.24k, 1%, 0603 VISHAY CRCW06033K24FKEA
37 1 R65 RES., CHIP, 2.43k, 1%, 0603 VISHAY CRCW06032K43FKEA
38 1 R66 RES., CHIP, 2.43k, 1%, 0603 VISHAY CRCW06032K43FKEA

9
dc1989abf
DEMO MANUAL DC1989A-B
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER
39 2 R95, R96 RES., CHIP, 4.99k, 1%, 0603 VISHAY CRCW06034K99FKEA
40 2 R99, R100 RES., CHIP, 200Ω, 1%, 0603 VISHAY CRCW0603200RFKEA
41 1 R101 RES., CHIP, 127Ω, 1%, 0603 VISHAY CRCW0603127RFKEA
42 1 R123 RES., CHIP, 1M, 1%, 0603 VISHAY CRCW06031M00FKEA
43 1 R105 RES., CHIP, 681k, 1%, 0603 VISHAY CRCW0603681KFKEA
44 1 R106 RES., CHIP, 3.3Ω, 1%, 0603 VISHAY CRCW06033R30FKEA
45 1 R107 RES., CHIP, 82.5Ω, 1%, 0603 VISHAY CRCW060382R5FKEA
46 2 R108, R118 RES., CHIP, 0.01Ω, 1%, 2010 VISHAY, WSL2010R0100FEA
47 1 R109 RES., CHIP, 100k, 1%, 0603 VISHAY CRCW0603100KFKEA
48 1 R110 TRIMMING POTENTIOMETER, 5k BOURNS, 3386P-1-502LF
49 2 R111, R115 RES., CHIP, 20k, 1%, 0603 VISHAY CRCW060320K0FKEA
50 1 R114 RES., CHIP, 154k, 1%, 0603 VISHAY CRCW0603154KFKEA
51 1 R117 RES., CHIP, 2Ω, 1%, 0603 VISHAY CRCW06032R00FKEA
52 2 SW1, SW2 CONNECTOR, SUB MINIATURE SLIDE
SWITCHES
C&K., JS202011CQN
53 3 U1, U2, U3 IC, LTM4676EY LINEAR TECH. LTM4676EY
54 1 U5 IC, 24LC025T-E/OT SOT-23 6-LEAD MICROCHIP, 24LC025T-E/OT
55 1 U6 IC., LT1129CS8-5, S8 LINEAR TECH. LT1129CS8-5
56 1 U7 IC., LTC6992-1, S6-TSOT LINEAR TECH. LTC6992CS6-1
57 1 U8 IC., LT1803IS5, S5-TSOT LINEAR TECH. LT1803IS5
Additional Demo Board Circuit Components
1 0 CIN16-CIN19 (OPT) CAP., OPTIONAL
2 0 C1, COUT2, C2, COUT3 (OPT), C6, C8, C9, COUT10,
C10, COUT11, C11, COUT13, C13, C14, C15, C16,
C17, C18, C19, C20, COUT14, COUT24, COUT21,
COUT22, COUT25, COUT27, COUT29, COUT30,
COUT31, COUT32, COUT35, COUT33, COUT36,
COUT37, COUT38, COUT34
CAP., OPTIONAL
3 0 R1, R3, R5, R17, R34, R31, R33, R29(OPT), R38,
R52, R55, R57, R59, R61, R28, R63, R71, R73,
R75, R77, R88, R91, R93, R94, R102, R103, R13,
R37, R62, R76, R79, R80, R21, R22, R23, R24,
R43, R44, R45, R46, R67, R68, R69, R70, R81,
R82, R68, R69, R70, R81, R82, R83, R84, R87
RES., OPTIONAL
4 0 U4 (OPT) OPTIONAL
Hardware: For Demo Board Only
1 23 E2-E24 TESTPOINT, TURRET, 0.062" MILL-MAX, 2308-2-00-80-00-00-07-0
2 2 JP1, JP2 HEADER, 1X3 PIN 0.079" SINGLE ROW SULLIN, NRPN031PAEN-RC
3 2 XJP1, XJP2 SHUNT, 0.079" CENTER SAMTEC, 2SN-KB-G
4 6 J1, J2, J3, J4, J5, J6 STUD, TESTPIN PEM KFH-032-10
5 12 J1, J2, J3, J4, J5, J6 (x2) NUT, BRASS 10-32 ANY #10-32
6 6 J1, J2, J3, J4, J5, J6 RING, LUG #10 KEYSTONE #10
7 6 J1, J2, J3, J4, J5, J6 WASHER, TIN PLATED BRASS 10EXT
8 4 (STAND-OFF) STAND-OFF, NYLON 0.50" TALL KEYSTONE, 8833(SNAP ON)
9 1 FAB, PRINTED CIRCUIT BOARD DEMO CIRCUIT TOP 1989A
parts List

10
dc1989abf
DEMO MANUAL DC1989A-B
schematic Diagram
5
5
4
4
3
3
2
2
1
1
D D C C B B A A
1210
0.035 VIA TESTPOINTS
121035V
4.5V - 16V
1210 1210
1210
6.3V 1210 1210
0805
ON
OFF RUN0
NOTE: UNLESS OTHERWISE SPECIFIED
1. ALL RESISTORS ARE 0603. ALL CAPACITORS ARE 0603.
1210 6.3V1210 1210 6.3V
µModule REGULATOR WITH DIGITAL POWER MANAGEMENT
0805
*
WHEN VIN < 5.75V, SHORT INTVCC TO VIN WITH R5,R34, R61.
*
1V / 75A
ALERTB SCL SDA RUN0 SYNC SHARE_CLK GPIO0B
VIN
VOUT0
VIN
VOUT0
VOSNS0+
SHARE_CLK
ALERTB
COMP0
COMP0
SCL SDA
VOSNS0-
GPIO0B
RUN0
VOSNS0+
SYNC
REVISION HISTORY DESCRIPTION DATEAPPROVEDECO REV
JIAN L.PROUCTION2 12-10-12
__
REVISION HISTORY DESCRIPTION DATEAPPROVEDECO REV
JIAN L.PROUCTION2 12-10-12
__
REVISION HISTORY DESCRIPTION DATEAPPROVEDECO REV
JIAN L.PROUCTION2 12-10-12
__
SIZE DATE:
IC NO. REV.
SHEET OF
TITLE:
APPROVALS
PCB DES.
APP ENG.
TECHNOLOGY Fax: [phone]
Milpitas, CA 95035 Phone: [phone] McCarthy Blvd. LTC Confidential-For Customer Use Only
CUSTOMER NOTICE
LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS; HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL APPLICATION. COMPONENT SUBSTITUTION AND PRINTED CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE OR RELIABILITY. CONTACT LINEAR TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE. THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND
SCHEMATIC
SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS.
SCALE = NONE
www.linear.com
2
Tuesday, May 28, 2013
16
HIGH EFFICIENCY, POLY-PHASE, DC/DC STEP-DOWN
HZ
JIAN L.
B
LTM4676EY DEMO CIRCUIT 1989A-B
SIZE DATE:
IC NO. REV.
SHEET OF
TITLE:
APPROVALS
PCB DES.
APP ENG.
TECHNOLOGY Fax: [phone]
Milpitas, CA 95035 Phone: [phone] McCarthy Blvd. LTC Confidential-For Customer Use Only
CUSTOMER NOTICE
LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS; HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL APPLICATION. COMPONENT SUBSTITUTION AND PRINTED CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE OR RELIABILITY. CONTACT LINEAR TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE. THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND
SCHEMATIC
SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS.
SCALE = NONE
www.linear.com
2
Tuesday, May 28, 2013
16
HIGH EFFICIENCY, POLY-PHASE, DC/DC STEP-DOWN
HZ
JIAN L.
B
LTM4676EY DEMO CIRCUIT 1989A-B
SIZE DATE:
IC NO. REV.
SHEET OF
TITLE:
APPROVALS
PCB DES.
APP ENG.
TECHNOLOGY Fax: [phone]
Milpitas, CA 95035 Phone: [phone] McCarthy Blvd. LTC Confidential-For Customer Use Only
CUSTOMER NOTICE
LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS; HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL APPLICATION. COMPONENT SUBSTITUTION AND PRINTED CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE OR RELIABILITY. CONTACT LINEAR TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE. THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND
SCHEMATIC
SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS.
SCALE = NONE
www.linear.com
2
Tuesday, May 28, 2013
16
HIGH EFFICIENCY, POLY-PHASE, DC/DC STEP-DOWN
HZ
JIAN L.
B
LTM4676EY DEMO CIRCUIT 1989A-B
+
COUT4
330uF
+
COUT4
330uF
R5 OPTR5 OPT
C3
220pF
C3
220pF
R25 0R25 0
R21 (OPT)R21 (OPT)
R8 10K R8 10K
E7
VDD25
E7
VDD25
R3 OPT R3 OPT
R4 0R4 0
COUT2
OPT
COUT2
OPT
R22 (OPT) R22 (OPT)
CIN4 10uF CIN4 10uF
R2 0 R2 0
CIN6 10uF CIN6 10uF
COUT10
OPT
COUT10
OPT
R26
0
R26
0
R12 10K R12 10K
R16 10 R16 10
R1
OPT
R1
OPT
P1P1
R24
(OPT)
R24
(OPT)
+
COUT8 330uF
+
COUT8 330uF
CIN1 10uF 1210 CIN1 10uF 1210
P3P3
R23
(OPT)
R23
(OPT)
C2 OPT C2 OPT
COUT6 100uF
1210
COUT6 100uF
1210
U1
LTM4676EY
U1
LTM4676EY
VOUT0
A1
VOUT0
A2
VOUT0
A3
VOUT0
D1
ISNS0b-
E1
ISNS0b+
F1
ISNS1b- G1
ISNS1b+ H1
VOUT1 J1
VOUT1 J2
VOUT1 J3
VOUT1 K1
VOUT0
B1
VOUT0
B2
VOUT0
B3
VOUT0
D2
ISNS0a-
E2
ISNS0a+
F2
ISNS1a- G2
ISNS1a+ H2
VOUT1 K2
VOUT1 K3
VOUT1 L1
VOUT1 L2
VOUT0
C1
VOUT0
C2
VOUT0
C3
VOUT0
D3
GND
A4
GND
A6
GND
A7
GND
A8
VOUT1 L3
VOUT1 M1
VOUT1 M2
VOUT1 M3
GND
A9
GND
A10
GND
B4
GND
B5
ASEL G4
FSWPHCFG H4
GND
B6
GND
B7
GND
B8
GND
B9
GPIO0 E4 GPIO1 F4
SNUB0
A5
GND
C4
TSNS0b
C5
TSNS0a
D5
ALERT E5
RUN0 F5
VOUT0CFG G5
VTRIM0CFG H5
TSNS1a J5
TSNS1b K5
GND
C6
SNUB1 M5
GND
C7
GND
C8
GND
C9
SDA D6
SCL E6
RUN1 F6
VOUT1CFG G6
VTRIM1CFG H6
VDD25 J6
WP K6
GND
D4
GND
E3
GND
F3
GND
F10
GND
G3
GND
G10
SYNC E7
GND
M9
GND
M10
SHARE_CLK H7
VDD33 J7
GND
G11
GND
G12
GND
L8 GND
L7
GND
L9
GND
H3
COMP0b
D8
COMP0a
E8
SGND
F7
SGND
F8
COMP1a H8
COMP1b J8
GND
H10
GND
J4
GND
M8
VOSNS0+
D9
VOSNS0-
E9
INTVCC F9 INTVCC G9
VOSNS1 H9
VORB1 J9
GND
J10
GND
L4
GND
L5
GND
K4
SW0
B10
DNC
E11
VORB0+
D10
VORB0-
E10
GND
L6
GND
K7
GND
K8
GND
K9
DNC
C10
SW1 L10
GND
M4
VINH0
B12 VINH0 B11 VINH0 A12 VINH0 A11
DNC
K10
VINL
F12
GND
M6
DNC
H11
VINH1 H12
VINH1 J11
VINH1 J12
VINH1 K11
VINH0
E12 VINH0
D12 VINH0 D11 VINH0 C12 VINH0 C11
VINL
F11
GND
M7
VINH1 K12
VINH1 L11
VINH1 L12
VINH1 M11
VINH1 M12
SGND
G7
SGND
G8
GND
D7
+
CIN3 150uF
+
CIN3 150uF
R20 22.6KR20 22.6K
R10 10K R10 10K
R19 787R19 787
E2
INTVCC
E2
INTVCC
R13 OPT R13 OPT
E8
GND0_SNS
E8
GND0_SNS
J1
VIN
J1
VIN
R9 10K R9 10K
R17 OPTR17 OPT
R7 10K R7 10K
J2
GND
J2
GND
R18
0
R18
0
P5P5
P2P2
R11 10K R11 10K
C4
3.3nF
C4
3.3nF
C5 10nF C5 10nF
E3
VIN
E3
VIN
CIN7 10uF CIN7 10uF
C1
OPT
C1
OPT
R14 2K R14 2K
CIN2 10uF 1210 CIN2 10uF 1210
COUT9
100uF
COUT9
100uF
E4
GND
E4
GND
R15 10K R15 10K
E6
VOUT0_SNS E6 VOUT0_SNS
SW1SW1
1
2
3
4
5
6
R120 0R120 0
+
COUT5
330uF
+
COUT5
330uF
CIN5 10uF CIN5 10uF
J3
VOUT0 J3 VOUT0
COUT1 100uF COUT1 100uF
COUT7 100uF
1210
COUT7 100uF
1210
R6 10K R6 10K
E5
VDD33
E5
VDD33
J4
GND
J4
GND
P4P4
COUT3
OPT
COUT3
OPT
COUT11
OPT
COUT11
OPT
C6 OPT C6 OPT