Linear Technology DC1274A Quick setup guide

1
dc1274af
DEMO MANUAL DC1274A
DESCRIPTION
LTM8040
36V, 1A Step-Down
µModule LED Driver
Demo circuit DC1274A features the LTM
®
8040 36V, 1A
step-down constant current μModule
®
LED driver. The
demonstration circuit is designed to drive a single LED
or string of LEDs at up to 1A from a wide input voltage
range. The maximum LED string voltage is 13V and the
minimum voltage varies depending upon the BIAS pin sup-
ply arrangement. The demonstration circuit is assembled
with the BIAS pin connected to the LEDA pin.
The LTM8040 runs at 500kHz switching frequency by
default. DC1274A can be adjusted to raise the switching L, LT, LTC, LTM, μModule, Linear Technology and the Linear logo are registered trademarks of
Linear Technology Corporation. All other trademarks are the property of their respective owners.
PERFORMANCE SUMMARY
BOARD PHOTO
frequency, lower the LED current, and implement PWM
dimming. The shutdown feature can be examined by con-
necting the shutdown terminal to ground. The LTM8040
data sheet must be read in conjunction with this demo
manual prior to working on or modifying demo circuit
DC1274A.
Design files for this circuit board are available at
http://www.linear.com/demo
(TA= 25°C)
PARAMETER CONDITIONS/NOTES VALUE
Input Voltage Range ILED = 1A, VLEDA = 3.3V 4V to 36V
Output Current (ILED) R3 = Open 1A
Switching Frequency R2 = Open 500kHz
Maximum Output Voltage (VLEDA), Open LED Voltage 13V

2
dc1274af
DEMO MANUAL DC1274A
QUICK START PROCEDURE
DC1274A is an easy way to evaluate the LTM8040. Refer
to the test procedures outlined below and Figure 1.
1. Make sure the power supply is less than 36V. With the
supply OFF, connect it to the VIN and GND terminals.
2. Connect an LED or string of LEDs between the LEDA
terminal and the GND terminal. For PWM dimming, the
PWM dimming MOSFET must be added to the PCB and
the string of LEDs must be attached between LEDA and
LED- terminals. However, for simplicity, the MOSFET is
not assembled on the board as shipped.
3. Turn on the input power supply and set the voltage
between 4V and 36V based on the forward voltage of
the LED(s) and desired output current. Please see the
LTM8040 data sheet for details.
4. Tie the shutdown terminal to ground in order to turn
the output off and examine the shutdown operation.
Allow the IC to run by releasing the shutdown terminal
connection to ground. The IC will run with the 100k
pull-up resistor from the shutdown terminal to VIN.
For LEDs or LED strings with a low forward voltage such
as a single red LED, the BIAS terminal can be disconnected
from the output (LPWR) and tied to the input (VIN). There
is a small trace on the back of the PCB (layer 4) that can
be cut in order to disconnect LPWR from BIAS. Please see
the LTM8040 data sheet for details regarding the proper
connection of the BIAS pin.

3
dc1274af
DEMO MANUAL DC1274A
QUICK START PROCEDURE
Figure 1. Proper Measurement Equipment Setup
V
+
–
V
+
–
A
–
+
A
–+
SHDN
OPTION
+–
OUTPUT CURRENT (mA)
0
0
EFFICIENCY (%)
10
30
40
50
400 800 1000
90
20
200 600
60
70
80
24VIN
12VIN
5VIN
Figure 2. Efficiency with Single 3.3VFLED at 1A. LED Current is Adjusted with ADJ Voltage

4
dc1274af
DEMO MANUAL DC1274A
PARTS LIST
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER
Required Circuit Components
1 1 C1 CAP, 1210 2.2μF 10% 50V X7R TDK C3225X7R1H225K
2 1 R1 RES, 0402 100k 5% 1/16W VISHAY CRCW0402100KJNED
3 1 U1 IC, MODULE LINEAR TECH. LTM8040EV
Optional Demo Circuit Components
1 0 C2 CAP, 0805 OPT OPT
2 0 Q1 N-CHANNEL MOSFET, SOT-23 OPT OPT
3 0 R2, R3 RES, 0402 OPT OPT
Hardware
1 10 E1-E10 TURRET MILL-MAX 2501-2-00-80-00-00-07-0

5
dc1274af
DEMO MANUAL DC1274A
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-
tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
SCHEMATIC DIAGRAM

6
dc1274af
DEMO MANUAL DC1274A
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
[phone] ●FAX: [phone] ●www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2011
LT 0711 • PRINTED IN USA
DEMONSTRATION BOARD IMPORTANT NOTICE
Linear Technology Corporation (LTC) provides the enclosed product(s) under the following AS IS conditions:
This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT
OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete
in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety
measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union
directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations.
If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date
of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR
ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LTC from all claims
arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all
appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or
agency certified (FCC, UL, CE, etc.).
No License is granted under any patent right or other intellectual property whatsoever. LTC assumes no liability for applications assistance,
customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind.
LTC currently services a variety of customers for products around the world, and therefore this transaction is not exclusive.
Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and
observe good laboratory practice standards. Common sense is encouraged.
This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LTC applica-
tion engineer.
Mailing Address:
Linear Technology
1630 McCarthy Blvd.
Milpitas, CA 95035
Copyright © 2004, Linear Technology Corporation

X-ON Electronics
Largest Supplier of Electrical and Electronic Components
Click to view similar products for LED Lighting Development Tools category:
Click to view products by Analog Devices manufacturer:
Other Similar products are found below :
MIC2870YFT EV ADP8860DBCP-EVALZ LM3404MREVAL ADM8843EB-EVALZ TDGL014 ISL97682IRTZEVALZ LM3508TLEV
EA6358NH MAX16826EVKIT MAX16839EVKIT+ TPS92315EVM-516 MAX1698EVKIT MAX6956EVKIT+ OM13321,598 DC986A
DC909A DC824A STEVAL-LLL006V1 IS31LT3948-GRLS4-EB 104PW03F PIM526 PIM527 MAX6946EVKIT+ MAX20070EVKIT#
MAX21610EVKIT# MAX20090BEVKIT# MAX20092EVSYS# PIM498 AP8800EV1 ZXLD1370/1EV4 MAX6964EVKIT
MAX25240EVKIT# MAX25500TEVKITC# MAX77961BEVKIT06# 1216.1013 TPS61176EVM-566 TPS61197EVM TPS92001EVM-628
1270 1271.2004 1272.1030 1273.1010 1278.1010 1279.1002 1279.1001 1282.1000 1293.1900 1293.1800 1293.1700 1293.1500