Linear Technology DC1962C Quick setup guide

Looking for a discount?
Check out our current promotions!
This coversheet was created by Verical, a division of Arrow Electronics, Inc. (“Verical”). The attached document was created by the part supplier,
not Verical, and is provided strictly 'as is.' Verical, its subsidiaries, affiliates, employees, and agents make no representations or warranties
regarding the attached document and disclaim any liability for the consequences of relying on the information therein. All referenced brands,
product names, service names, and trademarks are the property of their respective owners.
00000005981LF-000
EOS Power
Buy Now
We have 45,000 LP502030-PCM-NTC-LD-A02554 - EEMB - Lithium Battery Rectangular 3.7V 250mAh Rechargeable in
stock now. Starting at $0.034. This EEMB part is fully warrantied and traceable.
1-855-837-4225
Give us a call
International: 1-555-555-5555 1-415-281-3866
1-415-281-3866
Arrow Electronics,
Verical Division
P.O. Box 740970
Los Angeles, CA 90074-0970
Arrow Electronics, Inc
9201 East Dry Creek Road
Centennial, CO 80112
DC1962C
ANALOG DEVICES
Buy Now

1
dc1962cf
DEMO MANUAL DC1962C
Description
14-Channel Power Supply
System Employing LTC3880/LTC2974/LTC2977
Power System Managers with EEPROM
The DC1962C is a demonstration system that showcases three
different Linear Technology devices—the LT C
®
3880, LTC2974,
and LTC2977. The LTC2974 and LTC2977 devices are I2C/
SMBus/PMBus power system managers with EEPROM. The
LTC3880 isadualoutput PolyPhase
®
step-downDC/DCcontrol-
ler with digital power system management. The LTC3880 moni-
tors and controls 2 power supply rails, the LTC2974 monitors
and controls 4 power supply rails, and the LTC2977 monitors
and controls 8 power supply rails. The DC1962C demonstrates
theabilityof thesedevicesto sequence,trim,margin,supervise,
monitor, and log faults for fourteen power supplies. Each power
supply channel’s output voltage is monitored and each device
monitors its own internal die temperature. Six channels have
current and external temperature sensing.
The DC1962C is a single circuit board that contains fourteen
independent power supply rails. The board employs twelve
LTC3405A 300mA switch-mode regulators, which are config-
ured to be controlled by the LTC2974 (4) and LTC2977 (8). The
LTC3880’s two channels have much of the switching regulator
integrated, only requiring the external power stage (power
MOSFETs), inductor, and other passives. This board provides
a sophisticated fourteen channel digitally programmable power
supply system. The rail voltages are programmable within the
trim range shown in Table 1.
This demonstration system is supported by the LTpowerPlay™
graphical user interface (GUI) enabling complete control of the
featuresonallthreedevices.Together,the LTpowerPlay software
and DC1962C hardware system create a powerful development
environment for designing and testing configuration settings
of the LTC3880, LTC2974, and LTC2977. These settings can
be stored in each of the devices’ internal EEPROM or in a file.
This file can later be used to order pre-programmed devices or
to program devices in a production environment. The software
displays all of the configuration settings and real time measure-
ments from the three digital power ICs. Telemetry allows easy
access and decoding of the fault log created by each device.
The board comes pre-programmed with the EEPROM values
appropriate for the fourteen power supply rails on the DC1962C.
Just plug and play!
Multiple DC1962C boards can be cascaded together to form a
high channel count power supply (see the Multi-Board Arrays
section). This allows for the formation of a single, coherent
L, LT, LTC, LTM, Linear Technology, the Linear logo and PolyPhase are registered trademarks
and LTpowerPlay is a trademark of Linear Technology Corporation. All other trademarks are the
property of their respective owners.
power supply system. The user configures up to eight DC1962C
boards, thereby controlling up to 112 separate power supply
rails. This cascaded configuration demonstrates features of the
LT power system management ICs which enable timing and
fault information to be shared across multiple ICs.
The DC1962C demo board can be powered by an external power
supply, such as a +12VDC supply. Communication with the
software is provided through the DC1613 USB-to-I2C/SMBus/
PMBus Controller. The following is a checklist of items which
can be obtained from the LT C website or LT C Field Sales.
• USB-to-I2C/SMBus/PMBus Controller (DC1613)
• LTpowerPlay Software
DC1962C Features
• I2C/SMBus Serial Interface
• PMBus Compliant Command Set
• Configuration EEPROM with CRC
• Black Box Fault Logging to Internal EEPROM
• Differential Input, 16-Bit Δ∑ ADC with less than ±0.25% of
Total Unadjusted Error (±0.5% for LTC3880)
• Voltage Servos Precisely Adjust Supply Voltages
• LTC2974 and LTC2977 Utilize 10-Bit trim DACs with
Soft-Connect
• Telemetry Reads Back VIN, IIN, VOUT, IOUT, Temperature (Int.
and Ext.)
• Output Sequencer-Time Based orTracking(Tracking support
on LTC2974 Only)
• Supports Multichannel Fault Management
• Operates Autonomously without Additional SW
• Powered from 6V to 14V
• Packaging:
– LTC2974/LTC2977 in 64-lead QFN
– LTC3880 in 40-lead QFN
Design files for this circuit board are available at
http://www.linear.com/demo

2
dc1962cf
DEMO MANUAL DC1962C
performance summary
Specifications are at TA= 25°C
POWER SUPPLY CHANNEL CH(0:1) CH(2:5) CH(6:13)
Manager/Controller LTC3880 LTC2974 LTC2977
Nominal Untrimmed Output Voltages 0.85V, 1.1V
(Defined by Config)
1.5V, 1.8V, 2.0V, 2.2V 0.9V, 1.0V, 1.1V, 1.2V,
2.5V, 2.7V, 3.0V, 3.3V
Rated Output Current 0.3A
Default Margin Range ± 5%
Output Trim Range (VFS_VDAC = 1.38V) Each Channel Is Adjustable
from 0.5V to 4.5V (Note 1)
15%/–11% 15%/–11%
Temperature 1 Internal, 2 Ext. 1 Internal, 4 Ext. 1 Internal
Common Characteristics. Specifications Valid Over Full Operating Temperature Range
PARAMETER CONDITIONS
VALUE
MIN TYP MAX UNITS
VPWR Supply Input Voltage Range 6 14 V
ADC Total Unadjusted Error VIN_ADC ≥ 1V, Applies to LTC2974/LTC2977 ±0.25 %
VIN_ADC ≥ 1V, Applies to LTC3880 ±0.5 %
ADC Voltage Sensing Input Range Differential Voltage: VIN_ADC = (VSENSEPn– VSENSEMn) 0 6 V
Note 1: Note that VOUT_MAX limit is set to 2.5V by default. VOUT_MAX clamps the voltage setpoint to 2.5V. It is recommended that you change the VOUT_MAX
register and associated VOUT FAULT limit registers when changing VOUT to prevent the channel from faulting off.
The following list contain terms used throughout the document.
Channel – The collection of functions that monitor, supervise, and trim a given power supply rail.
EEPROM – Non-volatile memory (NVM) storage used to retain data after power is removed.
Margin – Term used typically in board level testing that increases/decreases the output voltage to look for sensitivity/
marginality problems
NVM – Non-volatile memory, see EEPROM.
Monitor – The act of measuring voltage, current, and temperature readings.
PMBus – An industry standard power-management protocol with a fully defined command language that facilitates
communication with power converters and other devices in a power system.
Rail – The final output voltage that the power supply controller manages.
Supervise – The act of quickly responding (warning or faulting) to a voltage, current, temperature condition that is
compared to pre-programmed values.
Trim – The act of adjusting the final output voltage. A servo loop is typically used to trim the voltage.
Glossary of terms

3
dc1962cf
DEMO MANUAL DC1962C
ltpowerplay Gui software
LTpowerPlay is a powerful Windows-based development environment that supports Linear Technology power system
management ICs with EEPROM, including the LTC2974 and LTC2977 4-channel and 8-channel PMBus power system
managers, and the LTC3880 dual output PolyPhase step-down DC/DC controller with digital power system manage-
ment. The software supports a variety of different tasks. You can use LTpowerPlay to evaluate Linear Technology ICs
by connecting to a demo board system. LTpowerPlay can also be used in an offline mode (with no hardware present)
in order to build a multi-chip configuration file that can be saved and re-loaded at a later time. LTpowerPlay provides
unprecedented system level diagnostic and debug features. It becomes a valuable diagnostic tool during board bring-up
to program or tweak the power management scheme in a system or to diagnose power issues when bringing up rails.
LTpowerPlay utilizes the DC1613 I2C/SMBus/PMBus Controller to communicate with one of many potential targets,
including the DC1962C demo system or a customer board. The software also provides an automatic update feature
to keep the software current with the latest set of device drivers and documentation. The LTpowerPlay software can
be downloaded from:
http://www.linear.com/ltpowerplay
Figure 1. Screenshot of the LTpowerPlay GUI

4
dc1962cf
DEMO MANUAL DC1962C
Quick start proceDure
To access technical support documents for LT C Digital Power Products visit “Help, View Online help” on the LTpow-
erPlay menu.
The following are examples of content available in the online help:
1. Demonstration and Tutorial Videos
• An updated Quick Start Demonstration video of LTpowerPlay and this demo board
• Product/Feature-specific demonstration and tutorial videos
2. Detailed Technical Documentation
• Schematic Checklists
• Device Programming Options
• Firmware ‘Getting Started’ guides with sample code (margining, reading telemetry, etc.)
The following procedure describes how to set up a DC1962C demo system.
1. Download and install the LTpowerPlay GUI: www.linear.com/ltpowerplay
2. Remove the board from the ESD protective bag and place it on a level surface. Connect the DC1613 I2C/SMBus/
PMBus Controller to the DC1962C board using the 12-pin ribbon cable.
Figure 2. Connecting DC1962C Board and the DC1613 I2C/SMBus/PMBus Controller

5
dc1962cf
DEMO MANUAL DC1962C
3. Confirm that the CONTROL switch is set to the RUN
position.
4. Plug the USB-to-I2C/SMBus/PMBus Controller into a
USB port on your PC. The board should power up with
all power good LEDs and 5V LED illuminated green. The
USB-to-I2C/SMBus/PMBusControllersupplies~100mA
of current which should be sufficient for a single demo
board.
5. Connect a 12VDC power supply with > 0.5A capacity to
the VIN input jack of any DC1962C, if multiple boards
are being powered.
6. Launch the LTpowerPlay GUI.
a. The GUI automatically identifies the DC1962C and
builds asystem tree for each power system manager.
The system tree on the left hand side will look as
below:
Note:For multiple boardarrays, the GUIautomatically
ensures each device has a unique address. In this
scenario, it is recommended at this point to store
these addresses to NVM (EEPROM) by clicking the
“RAM to NVM” icon in the toolbar.
b. A green message box will be displayed momentarily
in the lower left hand corner confirming that the
DC1962C is communicating.
Quick start proceDure
c. Save the demo board configuration to a (*.proj) file
by clicking the “Save” icon. This creates a backup
file. Name it whatever you want.
7. The CONTROL switch is configured to control all 14
channels. Slide the switch to RUN to enable, OFF to
disable all channels. For multiple board arrays, the
CONTROL switch is wired to a signal that is common
across all boards. All CONTROL switches must be set
to the RUN position to enable all boards.

6
dc1962cf
DEMO MANUAL DC1962C
Quick start proceDure
Loading a DC1962C Configuration (*.proj) File with the GUI
1. In the upper left hand corner of the GUI, File > Open > browse to your *.proj file. This will load the file into the GUI.
2. Click on the “Go Online” icon, then click on the “PC →RAM” icon. This loads the configuration
into the working RAM of the devices.
3. To store the configuration to NVM (EEPROM), click on the “RAM →NVM” icon as shown below.
Dc1962c Details - top siDe
Figure 3. DC1962C Top Side Details

7
dc1962cf
DEMO MANUAL DC1962C
common Demo BoarD operations
Margin All Rails
The digital power products on the DC1962C not only
monitor each of their respective outputs but can margin
the outputs either high or low. Margining is the operation
that moves a rail either up or down for testing purposes.
It allows a system to be fully characterized over supply
limits without the use of external hardware or resources.
The GUI provides an easy way to margin all rails high
or all low by clicking one of four buttons. To invoke the
margining dialog, click the GroupOp icon in the toolbar.
The buttons labeled “ignore faults” will margin
without creating a fault even if the fault limits are exceeded
(LTC2974 and LTC2977 only).
A look at the telemetry window shows the effect of the
margin high or margin low operation. The following screen
shot shows all rails going from nominal set points to
margin high, margin low, and back to nominal voltages.
Each of the power management ICs has a multiplexed ADC
that is used to provide voltage, current, and temperature
readback values. The telemetry plot in the GUI is similar to
a multichannel oscilloscope which is capable of displaying
any parameter that is displayed in the telemetry window.
Due to the nature of a multiplexed ADC converter, it has
an associated ADC loop time. The total ADC loop time
(~100ms to 160ms) for a given channel is dependent on
the device’s configuration. See corresponding data sheet.

8
dc1962cf
DEMO MANUAL DC1962C
Creating a Fault
There is a pushbutton on the DC1962C board that is used
to force a fault and demonstrate the demo board’s ability to
detectit and respond according to the configuration. When
depressed, the pushbutton creates a fault on channel 2,
the 1.5V output (GUI channel U1:0). The user should
see all outputs power off, the fault LED momentarily il-
luminate, the alert LED illuminate continuously, and all
rails sequence back on after a retry period. The user may
also short any power supply output indefinitely. This is a
good way to induce UV faults and shows that a shorted
channel will not be damaged. Use a jumper wire or a coin
to short any output.
common Demo BoarD operations
Clearing a Fault
To clear a fault, the user may click the CF icon in the
GUI or simply push the RESET pushbutton on the demo
board. In both cases, the red (+) on the CF icon and alert
LED on the board will be cleared. You will notice that all
rails are automatically re-enabled after a programmable
retry period. The alert LED may be cleared by clicking the
Clear Faults (CF) icon in the GUI. After clearing faults, the
system tree may remain “yellow” if any non-volatile fault
logs are present. For further information, see the Working
with the Fault Log section.
Reset the DC1962C
A reset pushbutton is provided on the board. To reset all
devices on the DC1962C board and reload the EEPROM
contents into operating memory (RAM), press RESET
(SW2) on the DC1962C. Note that the “RESET” icon in
the GUI tool bar issues a software reset for any LTC3880
device in the system. It is recommended that you use the
reset pushbutton on the board to provide a reset condition
to the entire system.
DC1962C LEDs
Each individual channel on DC1962C also has its own
green power good LED (RUN_CH0 through RUN_CH13).
When USB power (DC1613 Controller) or external power
(6V to 14V jack) is applied, the +5V green LED will illu-
minate, indicating that the power system managers are
powered. The red LEDs will illuminate when an alert or a
fault has occurred.

9
dc1962cf
DEMO MANUAL DC1962C
Figure 4. Sequencing Output Channels with DC1962C Using TON_DELAY
common Demo BoarD operations
Figure 5. TON_DELAY Configuration Figure 6. TOFF_DELAY Configuration
Sequencing Output Channels
The LTC3880, LTC2974, and LTC2977 have been pre-
configured with different TON_DELAY values for each
channel. The TON_DELAY parameter is applied to each
device relative to the respective CONTROL pin (RUN on
the LTC3880). On this demo board, all CONTROL/RUN
pins are wire OR’d. Therefore the TON and TOFF delays
are enforced relative to one edge. Figure 4 shows an oscil-
loscope screen capture of four output rails sequencing up.
The same applies to TOFF_DELAY values. When the
CONTROL switch is set to the OFF position, all rails will
power down sequentially based on each of the device’s
TOFF_DELAY values. Each channel has an LED which
visually indicates if the channel has power. When the
CONTROL pin is switched on and off, you will observe the
relative on/off timing of the 14 channels. Figures 5 and 6
show TON and TOFF delays for all channels at once. You
will notice in Figure 1 that the GUI shows idealized on/off
waveforms.Thisgraphical view shows therelative TON and
TOFF delays in response to an on/off command, whether
it comes from the CONTROL switch or PMBus command.
Once a new timing value is entered, the timing change will
be reflected in the idealized waveforms.

10
dc1962cf
DEMO MANUAL DC1962C
"Why Am I Off?” Tool
Use the “Why am I Off?” tool in the LTpowerPlay GUI to diagnose the reason a power supply channel is turned off.
The tool can be located in the top right corner of the GUI, above the Register Information tab. Hover your cursor over
this tab to show the tool.
common Demo BoarD operations
Figure 7. "Why Am I Off” Tool in the LTpowerPlay GUI
What Is a Fault Log?
A fault log is a non-volatile record of the power system
leading up to the time of fault. It holds the most recent
monitored values (uptime, voltage, current, temperature)
that can be analyzed to help determine the cause of the
fault. It is a powerful diagnostic feature of each of the
digital power managers on the DC1962C demo board.
Create a Fault and Fault Log
To create a fault log, you must create a fault, as described
in the Creating a Fault on page 8. Select the appropriate
device in the system tree by clicking on the U1 LTC2974
chip. We will proceed to work with the LTC2974 fault log.
aDvanceD Demo BoarD operations

11
dc1962cf
DEMO MANUAL DC1962C
aDvanceD Demo BoarD operations
Working with the Fault Log
Once a fault has occurred, the Fault Log (FL) icon
will show a red (+) sign on it, indicating that the GUI has
detected a fault log in one of the devices. Clicking the icon
will bring up a dialog box. Note that it is context sensitive.
Besurethat the desired device isselectedin the system tree.
Notice that the checkbox “Log to EEPROM on Fault” is
checked. Once a fault occurs, the device will automatically
write the fault log data to EEPROM (NVM). At this point,
the log is locked and will not change until it is cleared
by the user. To read the EEPROM log data, first click the
“EEPROM to RAM” button. At this point the RAM Log is
locked and not updated even though the telemetry read-
ings continue. Click the “Read NVM Log” button. The log
data will appear in the text box below.
The log contains timestamp, up-time, channel voltage
readings, an input voltage reading, an on-chip temperature
reading, etc. There will be a number of loops; each loop
contains data obtained in one ADC loop time with the
most recent ADC loop data on top and the oldest data at
the bottom of the log. The up-time indicates, at the time
of fault, the amount of time the device has been powered
up or time since the previous reset.
In this case, the fault log will show that channel U1:0
faulted due to a VOUT_UV_FAULT condition. On the pre-
vious telemetry loop, the channel voltage reading was a
nominal value (1.5V).
To clear the fault log, click the “Clear/Rearm EEPROM
Log” button. This allows the selected device to be ready
for a new fault event.

12
dc1962cf
DEMO MANUAL DC1962C
aDvanceD Demo BoarD operations
Fault Sharing Setup in the GUI
Fault sharing provides a means of propagating a fault
detected by a power manager to other power managers via
FAULT pins. Use the Fault Sharing Setup Tool to configure
the fault sharing in the GUI. Select the LTC2974 in the
system tree. Go to Utilities > Fault Sharing Diagram. For
more details on this topic, please refer to the MFR_FAULTB
propagate and response sections in the data sheet.
channels on the DC1962C demo board since the fault pins
are tied together.
NOTE: All FAULT pins on all power managers are tied to-
gether on the DC1962C demo board. These pins are open
drain and have a common pull-up resistor to provide a
logic high level (inactive). All FAULT pins are active low.
There are two types of actions to fault conditions: How a
channel responds to another channel’s fault and whether
a particular channel propagates its fault to other channels.
FAULT pins are bi-directional, meaning the device may
drive its fault pin low (output) or may respond to the fault
pin when another device drives it low (input). Because all
fault pins are wire OR’d on the DC1962C, this hardware
configuration allows one to program each device’s fault
settings on a channel-by-channel basis. By default, the
LTC2974 is configured to shut down its channels if
other devices fault and to propagate its own fault via the
FAULT pins. The LTC2977 is configured the same as the
LTC2974, however zone 1 (U2:4-U2:7) is configured to not
propagate a fault. A fault on these channels will cause only
that channel to fault off. You can think of the “Response”
switchesas “shut this channel down when anotherchannel
faults”, and the “Propagate” switches as “drive a fault pin
to broadcast to other channels that this channel faulted.”
Figure 8. Fault Sharing Utility in LTpowerPlay GUI
The LTC2974 fault sharing dialog will appear as shown in
Figure8.AllResponseandall Propagate switches are closed
by default. In this configuration, a fault on an LTC3880 or
LTC2977 channel will shut down all LTC2974 channels,
and a fault on any LTC2974 channel will propagate to all

13
dc1962cf
DEMO MANUAL DC1962C
Figure 9. Updated Fault Sharing Configuration
Fault Configuration Example
Let’s explore two different examples. Suppose we do not
want channel U1:0 (CH2 1.5V rail) to propagate its fault
to the other channels when U1:0 faults. And suppose we
do not want channel U1:1 (CH3 1.8V rail) to shut down in
response to another channel’s fault. We can configure the
switches as shown in Figure 9. Simply click the switches
to open/close. Click OK to close the dialog box. Click the
“PC →RAM” icon to write the changes to the DC1962C.
We can now create a fault on U1:0 (CH2) by shorting the
output to ground. Press the CREATE FAULT button on
the board. You will notice that the channel shuts off but
the other channels remain powered up because its fault
is not propagated to the other channels. After the retry
period, channel U1:0 (CH2) will power back up. We can
now observe the effect of changing the response setting on
U1:1 (CH3). If you short U1:2 (CH4 2.0V rail) to ground,
notice that all rails shut down except U1:1 (CH3). This is
an example of a keep-alive channel that remains powered
up independent of faults to other channels.
aDvanceD Demo BoarD operations

14
dc1962cf
DEMO MANUAL DC1962C
aDvanceD Demo BoarD operations
Up to eight DC1962C boards can be cascaded to control
up to 112 independent power supplies. The number of
boards is limited by an I/O expander chip that has three
address pins, allowing 8 different combinations. This
setup demonstrates the coordinated fault responses and
accurate time base shared across multiple power system
managers.
Procedure:
1. Stack the boards side-by-side by plugging JP1 of one
board into JP2 of another DC1962C board.
2. Ensure different slave address settings for each of the
boards. The address of each DC1962C board is deter-
mined by pins A2, A1 and A0 of the DIP switch JP1 on
the backside of the board. The setting must be unique
for each board in the array.
3. Plug in the +12V VIN power into one of the boards as
shown in Figure 10. Only one +12V power source is
allowed.
setup proceDure for multiBoarD arrays
The two LTC3880 channels can be uniquely configured
and any fault can be propagated or not. Since the LTC3880
GPIO pins are tied together, a fault on CH0 may be used to
turn off CH1. This is achieved by setting the appropriate
MFR_GPIO_PROPAGATE command code and the MFR_
GPIO_RESPONSE command to “inhibit.”

15
dc1962cf
DEMO MANUAL DC1962C
setup proceDure for multiBoarD arrays
Figure 10. Array of Multiple DC1962C Demo Boards
4. The USB-to-I2C/SMBus/PMBus Controller may be
plugged into any board. If no DC1962C boards show up
in the GUI, click the magnifying glass icon to enumer-
ate the I2C bus and find the addresses of the parts. Go
to step #2 to ensure that each board has a unique DIP
switch setting.
5. Since the individual CONTROL lines are connected
across the boards (CTRL is a common signal across
all boards in the array), make sure that all CONTROL
switches are set to the RUN position.
6. Re-launch LTpowerPlay. After launching, LTpowerPlay
will enumerate the entire board array and build a rep-
resentative system tree and read all hardware settings
into the GUI.
ATTENTION: Once the GUI has launched, click the “RAM
→NVM” button in the tool bar to ensure that the slave
addresses are retained after a power off or reset. Other-
wise you may lose communication with the slaves after a
power cycle or reset event.

16
dc1962cf
DEMO MANUAL DC1962C
Ensuring Slave Addresses Do Not Conflict
Thereis a small DIP switch on the backside of the DC1962C.
It is used to set the slave address of an I/O expander which
allows the addition of multiple boards to a setup. The I/O
setup proceDure for multiBoarD arrays
expander has a base address of 0x20. The DIP switch
settings set the offset. The three switches that may be
changed are labeled A0, A1, A2. Examples below set the
boards to address 0x20 and 0x27.
Figure 11. DIP Switch Set to All 0's
Figure 12. DIP Switch Set to All 1's

17
dc1962cf
DEMO MANUAL DC1962C
Dc1962c Details - top
Table 3. DC1962C - Default Switch Configuration (Default Position Shown in Grey in the Figure Above)
REFERENCE DESIGNATOR SIGNAL NAME USAGE DEFAULT
JP3 A0, A1, A2 DIP switch used to set the address offset OPEN
S1 CONTROL0 Switch used to enable/disable the CONTROL0 input pin of
LTC3880, LTC2974, and LTC2977
RUN

18
dc1962cf
DEMO MANUAL DC1962C
Dc1962c Details - Bottom

19
dc1962cf
DEMO MANUAL DC1962C
parts list
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER
Required Circuit Components
1 1 U8 IC DUAL PolyPhase CONTROLLER 40-QFN Linear Technology: LTC3880EUJ-1
2 1 U9 IC 8-CH PWR SYSTEM MANAGER 64-QFN Linear Technology: LTC2977CUP
3 1 U10 IC 4-CH PWR SYSTEM MANAGER 64-QFN Linear Technology: LTC2974CUP
Additional Demo Board Circuit Components
4 12 C1, C3, C5, C7, C64, C65, C66, C67, C68,
C69, C70, C71
CAP CER 220pF 50V 10% NPO 0603 NIC: NMC0603NPO221J50TRPF
5 8 C2, C4, C6, C8, C9, C10, C11, C12 CAP CER 2200pF 50V 20% X7R 0603 Murata: GRM188R71H222MA01D
6 30 C13, C14, C15, C16, C25, C26, C31, C43, C44,
C46, C47, C49, C50, C51, C52, C81, C82, C83,
C84, C85, C86, C87, C88, C92, C96, C97, C98,
C99, C115, C117
CAP CER 0.1µF 16V 10% X7R 0603 NIC: NMC0603X7R104K16TRPF
7 11 C17, C18, C106, C107, C108, C109, C110,
C111, C112, C113, C118
CAP CER 10000pF 50V 10% X7R 0603 TDK: C1608X7R1H103K
8 16 C19, C20, C21, C22, C23, C24, C32, C53, C54,
C55, C56, C57, C58, C59, C60, C72
CAP CER 10µF 10V 10% X5R 1210 Kemet: C1210C106K8PACTU
9 3 C27, C90, C93 CAP CER 4.7µF 16V 10% X5R 0603 TDK: C1608X5R1C475K
10 1 C28 CAP CER 10µF 25V 20% X5R 1210 Taiyo Yuden: TMK325BJ106MM-T
11 2 C29, C34 CAP CER 3300pF 50V 10% X7R 0603 Murata: GRM188R71H332KA01D
12 13 C30, C36, C39, C41, C42, C45, C48, C61, C62,
C63, C89, C114, C116
CAP CER 1µF 16V 10% X7R 0603 Taiyo Yuden: EMK107B7105KA-T
13 2 C33, C37 CAP CER 100pF 50V 10% X7R 0603 AVX: 06035C101KAT2A
14 2 C35, C95 CAP CER 68pF 50V 5% NPO 0603 AVX: 06035A680JAT2A
15 13 C38, C73, C74, C75, C76, C77, C78, C79, C80,
C102, C103, C104, C105
CAP CER 22µF 10V 10% X5R 1210 Kemet: C1210C226K8PACTU
16 1 C40 CAP CER 47pF 50V 5% NPO 0603 AVX: 06035A470JAT2A
17 1 C91 CAP TANT 47µF 16V 20% 7343 Kemet: T520D476M016ATE035
18 1 C94 CAP CER 4.7pF 50V NPO 0603 Murata: GRM1885C1H4R7CZ01D
19 2 C100, C101 CAP CER 47µF 10V 20% X7R 1210 Murata: GRM32ER71A476ME15L
20 4 D1, D2, D3, D4 DIODE SCHOTTKY 20V 1A SOD323 NXP Semiconductors:
PMEG2010EA,115
21 1 D5 DUAL SCHOTTKY DIODE 30V CC SOT-323-3 STMicroelectronics: BAT30CWFILM
22 2 L1, L2 INDUCTOR SHLD POWER 10.0µH SMD Abracon Corporation:
ASPI-0315FS-100M-T2
23 12 L3, L4, L5, L6, L8, L9, L10, L11, L12, L13,
L14, L15
INDUCTOR SHLD POWER 4.7µH SMD Abracon Corporation:
ASPI-0315FS-4R7M-T2
24 1 L7 INDUCTOR POWER 2.2µH 2.85A SMD Vishay: IHLP1616BZER2R2M01
25 15 P1, P2, P3, P4, P5, P6, P9, P10, P11, P12,
P13, P14, P15, P16, P17
LED GREEN HIGH BRIGHT ESS SMD Panasonic: LNJ337W83RA
26 2 P7, P8 LED RED HI BRT SS TYPE LO CUR SM Panasonic: LNJ208R8ARA
27 2 Q1, Q2 MOSFET N-CH DUAL 20V SSOT-6 Fairchild Semiconductor: FDC6401N
28 1 Q10 MOSFET P-CH 8V 860MA SOT323-3 Vishay/Siliconix: SI1305DL-T1-E3
29 6 Q3, Q4, Q5, Q6, Q7, Q8 TRANS GP SS PNP 40V SOT323 ON Semiconductor: MMBT3906WT1G
30 14 Q9, Q11, Q12, Q13, Q14, Q15, Q16, Q17, Q18,
Q19, Q20, Q21, Q22, Q23
MOSFET N-CH 30V 900MA SOT323-3 Vishay/Siliconix: SI1308EDL-T1-GE3