Linear Technology DC2077A Quick setup guide

1
dc2077af
DEMO MANUAL DC2077A
DESCRIPTION
LTC6431-20
50Ω20dB Gain Block
IF Amplifier
Demonstration circuit 2077A features the LT C
®
6431-20
50Ω gain block IF amplifier. The LTC6431-20 has a power
gain of 20.8dB and it is part of the LTC6431-YY amplifier
series.
The DC2077A demo board supports the LTC6431-YY am-
plifier family. The DC2077A demo board is optimized for
a frequency range from 100MHz to 1200MHz. It incorpo-
rates a minimum of passive components to configure the
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
BLOCK DIAGRAM
amplifier for various applications. The LTC6431-20 pro-
vides 50Ω single-ended input and output impedances so
thatitcanbeeasilyevaluatedwithmostRFtestequipment.
Design files for this circuit board are available at
http://www.linear.com/demo
Figure 1. LTC6431-20 Device Block Diagram
24 18
16
20dB
GAIN
BIAS AND
TEMPERATURE
COMPENSATION
VCC
9, 22
OUTIN
GND
8, 17, 23,
25 (EXPOSED PAD)
T_DIODE
643122 BD

2
dc2077af
DEMO MANUAL DC2077A
PERFORMANCE SUMMARY
OPERATION
Table 1. Typical Demo Board Performance Summary
SYMBOL PARAMETER CONDITIONS VALUE / UNIT
Power Supply
VCC Operating Supply Range All VCC Pins Plus OUT 4.75V to 5.25V
ICC Current Consumption Total Current 95mA
TA= 25°C, VCC = 5V
FREQUENCY
(MHZ)
POWER GAIN
|S21|
OUTPUT
THIRD-ORDER
INTERCEPT
POINT1
OIP3
OUTPUT
THIRD-ORDER
INTERMODU-
LATION1
OIM3
SECOND
HARMONIC
DISTORTION2
HD2
THIRD HARMONIC
DISTORTION2
HD3
OUTPUT 1DB
COMPRESSION
POINT
P1DB
NOISE FIGURE3
NF
100 20.2 47.2 –90.4 –56.8 –96.7 23.2 3.2
200 20.6 48.0 –91.9 –55.6 –92.9 22.4 2.7
240 20.6 47.9 –91.9 –52.5 –106.1 22.0 2.7
300 20.7 47.9 –91.9 –50.5 –83.1 21.8 2.8
400 20.6 46.9 –89.9 –50.4 –77.4 21.7 2.8
500 20.6 45.0 –86.0 –47.8 –72.6 21.8 2.9
600 20.6 42.5 –81.0 –43.7 –64.0 21.7 3.1
700 20.5 39.7 –75.5 –42.1 –60.7 21.4 3.3
800 20.5 38.6 –73.1 –40.6 –63.1 21.4 3.4
900 20.5 37.1 –70.3 –37.1 –60.4 21.1 3.7
1000 20.4 36.0 –68.0 –36.9 –55.1 20.8 3.8
1100 20.3 35.1 –66.2 –35.7 –54.5 20.4 3.9
1200 20.2 34.4 –64.8 –34.4 –53.6 20.3 4.1
Units dB dBm dBc dBc dBc dBm dB
Notes: All figures are referenced to J1 (Input Port) and J2 (Output Port).
1. Tw o -tone test conditions: Output power level = +2dBm/tone, tone spacing = 1MHz.
2. Single-tone test conditions: Output power level = +6dBm.
3. Small-signal noise figure.
The demo circuit 2077A is a high linearity, fixed gain
amplifier. It is designed for ease of use. Both the input
and output are internally matched to 50Ω single-ended
sourceandloadimpedance. Figure2showsthe DC2077A’s
S-parameters.
Figure4shows the demo circuit’s schematic. Theinputand
output DC blocking capacitors (C1 and C7) are required
because this device is internally DC biased for optimal
operation. The frequency appropriate choke (L1) and the
decoupling capacitors (C3 and C4) provide the proper
DC bias to the RF output node. Only a single 5V supply is
necessary for the VCC pins on the device.
L2andC6areoptionalparts. These additionalcomponents
allow for further optimization to lower or wider frequency
range applications.
A parallel 62pF (C2) and 348Ω (R1) input network has
been added to ensure low frequency stability. Note that the
input stability network does degrade performance below
150MHz. Low frequency performance can be improved
by increasing the value of capacitor C2.
The T_DIODE Pin (Turret E1) can be forward biased to
ground with 1mA of current. The measured voltage will
be an indicator of the chip junction temperature (TJ).

3
dc2077af
DEMO MANUAL DC2077A
OPERATION
Please note that a number of DNC pins are connected on
the demo board. These connections are not necessary for
normal operation. Failure to float these pins may impair
the operation of the device. Table 2 shows the function of
each input and output on the board.
Table 2. DC2077A Board I/O Descriptons
CONNECTOR FUNCTION
J1 (IN) Single-ended input. Impedance matched to 50Ω. Drive
from a 50Ω network analyzer or signal source.
J2 (OUT) Single-ended output. Impedance matched to 50Ω.
Drives a 50Ω network analyzer or spectrum analyzer.
E1 (T_DIODE) The measured voltage will be an indicator of the chip
junction temperature.
E2 (VCC) Positive supply voltage source.
E3 (GND) Supply ground.
Additional Information
As with any RF device, minimizing ground inductance is
critical. Care should be taken during the board layout when
usingtheseexposed pad packages. Themaximumnumber
of small-diameter vias should be placed underneath the
exposed pad. This will ensure a good RF ground and low
thermal impedance. Maximizing the copper ground plane
will also improve heat spreading and lower the inductance
to ground. It is a good idea to cover the via holes with
solder mask on the back side of the PCB to prevent solder
from wicking away from the critical PCB to exposed pad
interface.
The DC2077A is a wide bandwidth demo board, but it is not
intended for operation down to DC. The lower frequency
cutoff is limited by on-chip matching elements.
FREQUENCY (MHz)
0
|S21| (dB)
|S11|, |S12|, |S22| (dB)
16
20
24
NOMINAL WORKING
FREQUENCY RANGE
1600
12
8
14
18
22
10
6
4
–12
–4
4
–20
–28
–16
–8
0
–24
–32
–36
400 800 1200 2000
|S21|
|S22|
|S11|
|S12|
Figure 2. Demo Board S-Parameters
Table 3 shows the LTC643X-YY amplifier series and its
associateddemoboards. Each demo board liststhetypical
working frequency range and the input and output imped-
ance of the amplifiers.
Setup Signal Sources and Spectrum Analyzer
The LTC6431-20 is an amplifier with high linearity perfor-
mance.Therefore, the outputintermodulationproducts are
very low. Even using high dynamic range test equipment,
third-order intercept (IP3) measurements can drive test
setups to their limits. Consequently, accurate measure-
ment of IP3 for a low distortion IC such as the LTC6431-20
requires certain precautions to be observed in the test
setup as well as the testing procedure.
Table 3. The LTC643X-YY Amplifier Family and Corresponding Application Demo Boards
DEMO BOARD NUMBER
FREQUENCY RANGE
(MHz) NOTES/APPLICATIONS
BOARD’S IN/OUT
IMPEDANCE AMPLIFIER
AMPLIFIER’S
IMPEDANCE
DC1774A-A 50 to 350 Low Frequency 50Ω LTC6430-15 Differential 100Ω
DC1774A-B 400 to 1000 Mid Frequency 50Ω LTC6430-15 Differential 100Ω
DC1774A-C 100 to 1200 Wide Frequency 50Ω LTC6431-15 Single-Ended 50Ω
DC2032A 50 to 1000 Cable Infrastructure 75Ω LTC6430-15 Differential 100Ω
DC2077A 100 to 1200 Wide Frequency 50Ω LTC6431-20 Single-Ended 50Ω
DC2153A 700 to 1700 High Frequency 50Ω LTC6430-15 Differential 100Ω

4
dc2077af
DEMO MANUAL DC2077A
OPERATION
Setup Signal Sources
Figure 4 shows a proposed IP3 test setup. This setup has
low phase noise, good reverse isolation, high dynamic
range, sufficient harmonic filtering and wideband imped-
ance matching. The setup is outlined below:
a. Highperformance signalgenerators1 and 2(HP8644A)
are used. These suggested generators have low har-
monic distortion and very low phase noise.
b. High linearity amplifiers are used to improve the reverse
isolation.Thisprevents crosstalk betweenthetwosignal
generators and provides higher output power.
c. Alowpass filterisused tosuppressthe harmoniccontent
from interfering with the test signal. Note that second
order inputs can “mix” with the fundamental frequency
to form intermodulation (IM) products of their own. We
suggest filtering the harmonics to -50dBc or better.
d. The signal combiner from Mini-Circuits (ADP-2-9)
combines the two isolated input signals. This combiner
has a typical isolation of 27dB. For improved VSWR and
isolation, the H-9 signal combiner from MA/COM is an
alternative which features >40dB isolation and a wider
frequency range. Passive devices (e.g. combiners) with
magnetic elements can contribute nonlinearity to the
signal chain and should be used cautiously.
e. The attenuator pads on all three ports of the signal
combiner will further support isolation of the two input
signalsources.They alsoreducereflections andpromote
maximum power transfer with wideband impedance
matching.
Setup the Spectrum Analyzer
a. Adjust the spectrum analyzer for maximum possible
resolution of the intermodulation products’ amplitude
in dBc. A narrower resolution bandwidth will take a
longer time to sweep.
b. Optimize the dynamic range of the spectrum analyzer
by adjusting the input attenuation. First increase the
spectrum analyzer’s input attenuation (normally in
steps of 5dB or 10dB). If the IM product levels decrease
when the input attenuation is increased, then the input
power level is too high for the spectrum analyzer to
make a valid measurement. Most likely, the spectrum
analyzer’s 1st mixer was overloaded and producing its
own IM products. If the IM reading holds constant with
increased input attenuation, then a sufficient amount
of attenuation was present. Adding too much attenua-
tion will bury the intended IM signal in the noise floor.
Therefore, select just enough attenuation to achieve a
stable and valid measurement.
c. In order to achieve this valid measurement result, the
test system must have lower total distortion than the
DUT’s intermodulation. For example, to measure a
48dBm OIP3, the measured intermodulation products
will be –92dBc below the –18dBm per tone input level
andthetest system musthaveintermodulation products
approximately –98dBc or better. For best results, the
IM products and noise floor should measure at least
–102dBc before connecting the DUT.

5
dc2077af
DEMO MANUAL DC2077A
QUICK START PROCEDURE
Demo circuit 2077A can be set up to evaluate the perfor-
mance of the LTC6431-20. Refer to Figure 3 for proper
equipment connections and follow the procedure below:
Tw o -Tone Measurement
Connect all test equipment as suggested in Figure 3.
1. The power labels of VCC 4.75V-5.25V and GND directly
correspond to the power supply. Typical current con-
sumption of the LTC6431-20 is about 95mA.
2. Apply two independent signals f1 and f2 from signal
generator 1 and signal generator 2 at 240MHz and
241MHz, while setting the amplitude to –18dBm/tone
at the demo board input (J1).
3. Monitor the output tone level on the spectrum analyzer.
Adjust the signal generator levels such that the output
power measures +2dBm/tone at the amplifier output J2,
aftercorrectingforexternalcablelossesandattenuations.
4. Change the spectrum analyzer’s center frequency and
observe the two IM3 tones at 1 MHz below and above
theinputfrequencies.The frequencies of IM3_LOW and
IM3_HIGH are 239 MHz and 242 MHz, respectively. The
measurement levels should be approximately –92dBc;
+48dBmis typicalOIP3performance fortheLTC6431-20
at 240MHz.
The OIP3 calculation is:
OIP3 = POUT + ∆IMD3/2
where:
POUT is the lower output signal power of the funda-
mental products.
∆IMD3 = POUT – PIM3; PIM3 is the higher third-order
intermodulation product.
Single-Tone Measurement
5. Continue with Step 4 above, turn off one signal source
to measure gain and harmonic distortions.
COMBINER
Mini-Circuits
ADP-2-9
SIGNAL
GENERATOR 1 HP8644A
HP8644A
LOWPASS FILTER
LOWPASS FILTER
VCC = 4.75V TO 5.25V
6dB ATTN PAD
(OPTIONAL)
6dB ATTN PAD
(OPTIONAL)
3dB ATTENUATION
PAD
20dB ATTENUATION
PAD
COAXIAL
CABLE
SPECTRUM
ANALYZER
Rohde & Schwarz
FSEM30
AMPLIFIER
Mini-Circuits
ZHL-2 OR EQUIVALENT
AMPLIFIER
Mini-Circuits
ZHL-2 OR EQUIVALENT
SIGNAL
GENERATOR 2
DC POWER SUPPLY
GND V+
Figure 3. Proper Equipement Setup for IP3 Measurement

6
dc2077af
DEMO MANUAL DC2077A
PARTS LIST
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER
1 3 C1, C3, C7 CAP., X7R, 1000pF, 50V 5%, 0603 AVX, 06035C102JAT2A
2 1 C2 CAP., NPO, 62pF, 25V, 5%, 0402 AVX, 04023A620JAT
3 1 C4 CAP., X5R, 0.1µF, 10V, 10%, 0603 AVX, 0603ZD104KAT2A
4 2 C5, C8 CAP., X7R, 1000pF, 50V 5%, 0402 AVX, 04025C102JAT2A
5 1 C6 CAP., OPT, 0603
6 3 E1-E3 TESTPOINT, TURRET, 0.093" MILL-MAX, 2501-2-00-80-00-00-07-0
7 2 J1-J2 CONN., SMA 50Ω EDGE-LAUNCH E.F.JOHNSON, 142-0701-851
8 1 L1 INDUCTOR, CHIP, 560nH, 5%, 0603LS-1608 COILCRAFT, 0603LS-561XJLB
9 1 L2 RES., CHIP, 0Ω, 0603 VISHAY, CRCW06030000Z0ED
10 1 R1 RES., CHIP, 348Ω, 1%, 1/16W, 0402 VISHAY,CRCW0402348RFKED
11 0 R3 RES., OPT, 0402
12 1 U1 BALANCED AMPLIFIER LTC6431AIUF-20, QFN24UF-4X4 LINEAR TECH., LTC6431AIUF-20

7
dc2077af
DEMO MANUAL DC2077A
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-
tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
Figure 4. DC2077A Demo Board Schematic
SCHEMATIC DIAGRAM
5 5
4 4
3 3
2 2
1 1
D D C C B B A A
  

 
 


 
   
 

   
 

   
 

 
 
 




TECHNOLOGY
    

        













 
 
 




TECHNOLOGY
    

        













 
 
 




TECHNOLOGY
    

        













   








     
   
  

   


   
   









 


 







  
 
 
 
 
 
 








 


 


 
 










   

   
    





   

   







8
dc2077af
DEMO MANUAL DC2077A
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
[phone] ●FAX: [phone] ●www.linear.com
 LINEAR TECHNOLOGY CORPORATION 2014
LT 0314 • PRINTED IN USA
DEMONSTRATION BOARD IMPORTANT NOTICE
Linear Technology Corporation (LT C ) provides the enclosed product(s) under the following AS IS conditions:
This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT
OR EVALUATION PURPOSES ONLY and is not provided by LT C for commercial use. As such, the DEMO BOARD herein may not be complete
in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety
measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union
directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations.
If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date
of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR
ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LT C from all claims
arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all
appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or
agency certified (FCC, UL, CE, etc.).
No License is granted under any patent right or other intellectual property whatsoever. LT C assumes no liability for applications assistance,
customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind.
LT C currently services a variety of customers for products around the world, and therefore this transaction is not exclusive.
Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and
observe good laboratory practice standards. Common sense is encouraged.
This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LT C applica-
tion engineer.
Mailing Address:
Linear Technology
1630 McCarthy Blvd.
Milpitas, CA 95035
Copyright © 2004, Linear Technology Corporation

X-ON Electronics
Largest Supplier of Electrical and Electronic Components
Click to view similar products for RF Development Tools category:
Click to view products by Analog Devices manufacturer:
Other Similar products are found below :
MAAM-011117 MAAP-015036-DIEEV2 EV1HMC1113LP5 EV1HMC6146BLC5A EV1HMC637ALP5 EVAL-ADG919EBZ ADL5363-
EVALZ LMV228SDEVAL SKYA21001-EVB SMP1331-085-EVB EV1HMC618ALP3 EVAL01-HMC1041LC4 MAAL-011111-000SMB
MAAM-009633-001SMB MASW-000936-001SMB 107712-HMC369LP3 107780-HMC322ALP4 SP000416870 EV1HMC470ALP3
EV1HMC520ALC4 EV1HMC244AG16 MAX2614EVKIT# 124694-HMC742ALP5 SC20ASATEA-8GB-STD MAX2837EVKIT+
MAX2612EVKIT# MAX2692EVKIT# EV1HMC629ALP4E SKY12343-364LF-EVB 108703-HMC452QS16G EV1HMC863ALC4 119197-
HMC658LP2 EV1HMC647ALP6 ADL5725-EVALZ 106815-HMC441LM1 EV1HMC1018ALP4 UXN14M9PE MAX2016EVKIT
EV1HMC939ALP4 MAX2410EVKIT MAX2204EVKIT+ EV1HMC8073LP3D SIMSA868-DKL SIMSA868C-DKL SKY65806-636EK1
SKY68020-11EK1 SKY67159-396EK1 SKY66181-11-EK1 SKY65804-696EK1 SKY13396-397LF-EVB