Linear Technology LTC2107 Quick setup guide

1
dc2183af
DEMO MANUAL DC2183A
Description
LTC2107
16-BIT, 210 Msps ADCs
Demonstration circuit 2183A supports the LT C
®
2107, a
high speed and high dynamic range ADC. It was specially
designed for applications that require a single-ended AC-
coupled input. DC2183 supports the LTC2107 using the
DDR LVDS output mode.
The LTC2107 characteristics are listed in Table 1. De-
pending on the version, the circuitry on the analog inputs
is optimized for analog input frequencies from 5MHz to
70MHz or 70MHz to 180MHz.
L, LT , LT C , LT M , Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
performance summary
Refer to the LTC2107 data sheet for proper input networks
for different input frequencies.
Design files for this circuit board are available at
http://www.linear.com/demo/DC2183A
Specifications are at TA= 25°C
PARAMETER CONDITIONS MIN TYP MAX UNITS
Supply Voltage – DC2183 This supply must provide up to 800mA. 3.3 5.0 V
Analog Input Range Depending on PGA setting 1.6 2.4 VP-P
Logic Input Voltages Minimum Logic High
Maximum Logic Low
1.2
0.6
V
V
Logic Output Voltages (Differential) Nominal Logic Levels
(100Ω load, 3.5mA Mode, 1.25V common mode)
Minimum Logic Levels
(100Ω load, 3.5mA Mode, 1.25V common mode)
0.350
0.247
V
V
Sampling Frequency (Encode Clock Frequency) 10 210 MHz
Convert Clock Level (Single Ended) Logic Levels (ENC–tied to GND) 0 2.5 V
Convert Clock Level (Differential) Minimum Logic Levels
(ENC–not tied to GND, 1.2V common mode)
0.2 V
Table 1: DC2183 Variants
DC2183 VARIANTS ADC PART NUMBER RESOLUTION MAXIMUM SAMPLE RATE INPUT FREQUENCY
2183A-A LTC2107 16-BIT 210 Msps 5MHz to 70MHz
2183A-B LTC2107 16-BIT 210 Msps 70MHz to 180MHz
Downloaded from Arrow.com.

2
dc2183af
DEMO MANUAL DC2183A
Quick start proceDure
DC2183 is easy to set up to evaluate the performance
of the LTC2107 A/D converter. Refer to Figure 1 for
proper measurement equipment set-up and follow the
procedure below:
Setup
The DC1371 Data Acquisition and Collection System was
supplied with the DC2183 board. Follow the DC1371 Quick
Start Guide to install the required software and for con-
necting the DC1371 to the DC2183 and to a PC.
Figure 1. DC2183 Proper Measurement Equipment Setup
(zoom in for detail)
SINGLE-ENDED
ANALOG INPUT.
ABSORPTIVE FILTER IS REQUIRED
FOR DATA SHEET PERFORMANCE
SINGLE-ENDED ENCODE CLOCK.
USE A LOW-JITTER SIGNAL GENERATOR WITH PROPER FILTERING
JUMPERS SHOWN IN THEIR DEFAULT POSITIONS
THE DC2183 CONNECTS TO THE DC1371 VIA AN FMC CONNECTOR
J1
3.3V
TO 5V
Downloaded from Arrow.com.Downloaded from Arrow.com.

3
dc2183af
DEMO MANUAL DC2183A
Quick start proceDure
HARDWARE SETUP
SMAs:
J2: Analog Input. Apply a signal to J2 from a 50Ω driver.
Absorptive filters are required for data sheet performance.
J3: Encode Clock Input. Apply a clock signal to this SMA
connector from a 50Ω driver. A filter is required for data
sheet performance.
J4: Encode Clock Input For Differential Signals. By default
the DC2183 is defined to accept a single-ended clock sig-
nal. It can be modified to accept a differential clock signal
throughJ3andJ4.Somecomponentchangesarerequired,
see the Encode Clock section for more information.
MMCX Connectors:
J1: Optional Analog Input. As a default, this connector
is not populated. Standard MMCX connectors should be
used. To connect this connector to the input of the ADC,
populate R22 and remove J2 completely. By using this
connector, the DC2183 becomes fully compliant with the
FMC specification.
Turrets:
VIN: Positive Input Voltage for the ADC and Digital Buffers.
This voltage feeds a regulator that supplies the proper
voltages for the ADC and buffers. The voltage range for
this turret is 3.3V to 5V.
EXTREF: OptionalReferenceVoltage. This pin is connected
directly to the SENSE pin of the ADC. Connect EXT REF to
a1.25Vexternal reference and the external reference mode
is automatically selected. The external reference must be
1.25V ±25mV for proper operation. If no external voltage
is supplied, this pin will be pulled up to 2.5V through a
weak pull-up resistor.
GND: Ground Connection. This demo board only has a
single ground plane. This turret should be tied to the GND
terminal of the power supply being used.
Jumpers:
The DC2183 demonstration circuit should have the fol-
lowing jumper settings as default positions (per Figure1)
which configure the ADC in serial programming mode.
In the default configuration JP1-JP2 should be left in the
default locations. This will pull PAR/SER low, and the
required pins high through weak pull-up resistors so the
SPI commands can be sent from the PC. If JP1 is set to
PAR then jumpers JP1-JP2 can be configured manually.
JP1: PAR/SER: Selects Parallel or serial programming
mode (Default: Serial)
CMOS/LVDS: In Serial Programming Mode (SER), this
pin should be in the LVDS position to allow for serial data
transfer. (Default: LVDS or up) In the Parallel Program-
ming Mode (PAR), this pin controls the Digital Output
Mode. When this pin is in the CMOS position, the Full-Rate
CMOS Output Mode is enabled. When this pin is in the
LVDS position, the Double Data Rate LVDS Output Mode
(with 3.5mA output current) is enabled. Note: When using
the DC1371, parallel mode DDR LVDS must be selected.
JP2: PGA: In Serial Programming Mode (SER), this pin is
pulled high through a weak pull-up resistor to allow serial
data transfer. In the Parallel Programming Mode (PAR),
this pin controls the Programmable Gain Amplifier front-
end, PGA. In the 1x jumper position a front-end gain of
1x is selected, input range of 2.4VP-P. In the 3/2 jumper
position a front-end gain of 1.5x is selected, input range
of 1.6VP-P. (Default: 3/2 or up)
RAND: In Serial Programming Mode (SER), this pin
is pulled high through a weak pull-up resistor to allow
serial data transfer. In the Parallel Programming Mode
(PAR), this pin becomes the Digital Output Randomization
Control Bit. When this pin is in the OFF position, digital
output randomization is disabled. When this pin is in the
ON position, digital output randomization is enabled. To
decode the randomized data, exclusive-OR each bit with
the least significant bit. This is done for you in PScope
when the randomizer option is toggled.(Default: ON or up).
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

4
dc2183af
DEMO MANUAL DC2183A
JP3: SHUTDOWN: In the RUN position this pin results in
normal operation of the ADC. In the SHDN position the
ADC is powered down and the digital outputs are set in
high impedance state. (Default: RUN or down)
JP4: EEPROM: EEPROM Write Protect. For factory use
only. Should be left in the enable (PROG) position.
JP5: Overflow Test Point: This is a test point for the dif-
ferential overflow signal. This jumper can be installed to
provide a convenient way to probe the overflow signal.
(Default: removed)
JP6: Clock Term: This jumper provides termination volt-
ages for various signaling standards. LVPECL, CML, and
LVDS termination voltages can be selected. The selected
voltage is then used to terminate the clock input through
50Ω resistors. By removing the jumper completely an ex-
ternal voltage can be applied directly to pin 5 of JP6 so an
arbitrary signaling scheme can be used. (Default: LVPECL)
APPLYING POWER AND SIGNALS TO THE DC2183
DEMONSTRATION CIRCUIT
If a DC1371 is used to acquire data from the DC2183,
the DC1371 must FIRST be connected to a powered USB
port and provided an external 5 Volts BEFORE applying
+3.3V to +5.0V across the pins marked VIN and GND on
the DC2183. DC2183 requires at least 3.3V for proper
operation. Regulators on the board produce the voltages
required for the ADC. The DC2183 demonstration circuit
requires up to 800mA. The DC2183 should not be removed
or connected to the DC1371 while power is applied.
ANALOG INPUT NETWORK
Apply the analog input signal of interest to the SMA con-
nector on the DC2183 demonstration circuit board marked
J2. In the default setup, the DC2183 has an SMA input that
is meant to be driven with a 50Ω source. The DC2183 is
populated with an input diplexer filter to provide a 50Ω
characteristic impedance over all frequencies. This can
be modified to produce different frequency responses
as needed.
In almost all cases, off-board absorptive filters will be
required on the analog input of the DC2183 to produce
data sheet SNR.
The off-board filter should be located close to the input
of the demo board to avoid reflections from impedance
discontinuitiesatthedrivenend of a long transmission line.
Most filters do not present 50Ω outside the passband. In
some cases, 3dB to 10dB pads may be required to make
the filter look more absorptive to obtain low distortion.
ENCODE CLOCK
Applyanencodeclocktothe SMA connector on the DC2183
demonstration circuit board marked J3. As a default the
DC2183 is populated to have a single ended clock input.
For the best noise performance, the encode input must
be driven with a very low jitter signal generator source.
The amplitude should be as large as possible up to 2VP–P
or 10dBm.
The DC2183 demo board is designed to accept single
ended signals as a default. To modify the DC2183 to ac-
cept a differential signal, remove C31 and populate R18
with a0Ω resistor. Changing the position of JP6 to CML,
LVDS, or LVPECL selects the proper termination for your
input signal. These SMAs are positioned 0.5” apart to
accommodate LT C differential clock boards.
Quick start proceDure
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

5
dc2183af
DEMO MANUAL DC2183A
SOFTWARE
The DC1371 is controlled by the PScope System Software
which can be downloaded from the Linear Technology
®
websiteat http://www.linear.com/software/ . If a DC1371
was provided, follow the DC1371 Quick Start Guide and
the instructions below.
To start the data collection software, if PScope.exe is in-
stalled (by default) in \Program Files\LT C \PScope\, double
click the PScope icon or bring up the run window under
the start menu and browse to the PScope directory and
select PScope.
If the DC2183 demonstration circuit is properly connected
to the DC1371, PScope should automatically detect the
DC2183, and configure itself accordingly. If necessary,
the procedure below explains how to manually configure
PScope.
Under the Configure menu, go to ADC Configuration...
Check the Config Manually box and use the following
configuration options, see Figure 2:
Manual Configuration settings:
Bits: 16
Alignment: 16
FPGA Ld: S2157
Channs: 1
Bipolar: Unchecked
Positive-Edge Clk: Unchecked
Figure 2. ADC Configuration
If everything is hooked up properly, powered and a suit-
able convert clock is present, clicking the Collect button
should result in time and frequency plots displayed in
the PScope window. Additional information and help for
PScope is available in the DC1371 quick start guide and in
the online help available within the PScope program itself.
Quick start proceDure
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

6
dc2183af
DEMO MANUAL DC2183A
SERIAL PROGRAMMING
PScope has the ability to program the DC2183 board
serially through the DC1371. There are several options
available for the LTC2107 that are only available through
serial programming. PScope allows all of these features
to be tested.
These options are available by first clicking on the Set
Demo Bd Options icon on the PScope toolbar (Figure 3).
Figure 3. PScope Toolbar
This will bring up the menu shown in Figure 4.
Figure 4. Demobd Configuration Options.
This menu allows any of the options available for the
LTC2107 to be programmed serially. The LTC2107 has
the following options:
Sleep Mode – Selects between normal operation and
sleep mode:
• Off (Default) – Entire ADC is powered, and active
• On – The entire ADC is powered down
Dither – Selects between internal dither being enabled
or disabled:
• Enabled (Default) – Internal dither enabled
• Disabled – Internal dither disabled
Gain (PGS) – Selects input range of the ADC:
• 1.0 (Default) – Selects the 2.4V input range
• 1.5 – Selects the 1.6V input range
Duty Cycle Stabilizer – Enables or disables duty cycle
stabilizer:
• Stabilizer off (Default) – Duty cycle stabilizer disabled
• Stabilizer on – Duty cycle stabilizer enabled
ClkOut Invert – Selects the polarity of the CLKOUT signal:
• Disabled (Default) – Normal CLKOUT polarity
• Enabled – CLKOUT polarity is inverted
ClkOutPhase–SelectsthephasedelayoftheCLKOUTsignal:
• 0 deg (Default) – No CLKOUT delay
• 45 deg – CLKOUT delayed by 45 degrees
• 90 deg – CLKOUT delayed by 90 degrees
• 135 deg – CLKOUT delayed by 135 degrees
Keep Alive Osc – Enables or disables the internal keep
alive oscillator:
• Disabled (Default) – Keep alive oscillator is disabled
• Enabled – Keep alive oscillator is enabled
Quick start proceDure
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

7
dc2183af
DEMO MANUAL DC2183A
Encode Termination – Enables or disables LVDS internal
termination:
• Disabled (Default) – Disables internal termination
• Enabled – Enables internal termination
LVDS Current – Selects the LVDS output drive current:
• 1.75mA - LVDS output driver current
• 2.1mA - LVDS output driver current
• 2.5mA - LVDS output driver current
• 3.0mA - LVDS output driver current
• 3.5mA (Default) - LVDS output driver current
• 4.0mA - LVDS output driver current
• 4.5mA - LVDS output driver current
Tw o ’s Complement – Enables two’s complement mode:
• Enabled (Default) – Selects two’s complement mode
• Disabled – Selects offset binary mode
Randomizer – Enables data output randomizer:
• Disabled (Default) – Disables data output randomizer
• Enabled – Enables data output randomizer
ABP – Alternate Bit Polarity (ABP) mode:
• Disabled (Default) – Disables alternate bit polarity
• Enabled – Enables alternate bit polarity (Before enabling
ABP, be sure the part is in offset binary mode)
Output Test – Selects digital output test patterns:
• None (Default) – ADC data presented at output
• All out = 1 – All digital outputs are 1
• All out = 0 – All digital outputs are 0
• Checkerboard – OF and D15-D0 alternate between 1
0101 0101 1010 0101 and 0 1010 1010 0101 1010
on alternating samples
• Alternating – Digital outputs alternate between all 1s
and all 0s on alternating samples
Once the desired settings are selected hit OK and PScope
will automatically update the register of the device on the
DC2183 demo board.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

8
dc2183af
DEMO MANUAL DC2183A
parts List
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER
Required Circuit Components
1 2 C1, C12 CAP., X7R, 0.1µF, 16V 10% 0402 AVX, 0402YC104KAT2A
2 2 C2, C4 CAP., X5R, 100µF, 16V 20% 1210 TAIYO YUDEN, EMK325ABJ107MM-T
3 2 C3, C22 CAP., X5R, 1µF, 25V 10% 0603 TDK, C1608X5R1E105K080AC
4 3 C5, C6, C7, C31 CAP., X7R, 0.01µF, 16V 10% 0402 TDK, C1005X7R1C103K
5 5 C11, C14, C15, C23, C29 CAP., X5R, 0.1µF, 16V 10% 0402 AVX, 0402YD104KAT2A
6 1 C13 CAP., X5R, 2.2µF, 16V 20% 0603 AVX, 0603YD225MAT2A
7 4 C16, C19, C20, C24 CAP., X5R, 10µF, 16V 20% 1206 TDK, C3216X5R1C106M
8 1 C17 CAP., X5R, 2.2µF, 16V 20% 0402 TDK, C1005X5R1C225M050BC
9 0 C18, C30 CAP., OPT, 0402 OPTION
10 1 C21 CAP., X5R, 47µF, 16V 20% 1206 TDK, C3216X5R1C476M160AB
11 1 C25 CAP., X7R, 10µF, 16V 10% 0805 SAMSUNG, CL21B106KOQNNNE
12 2 C26, C27 CAP., COG, 2200pF, 25V 5% 0402 KEMET, C0402C222J3GACTU
13 0 C28 CAP., OPT, 0201 OPTION
14 1 E1 TEST POINT, TURRET, .061, PBF MILL-MAX, 2308-2-00-80-00-00-07-0
15 2 E2, E3 TEST POINT, TURRET, .094, PBF MILL-MAX, 2501-2-00-80-00-00-07-0
16 3 JP1, JP2, JP6 HEADER, 2X3 PIN, 0.079CC SULLINS, NRPN032PAEN-RC
17 2 JP3, JP4 HEADER, 3 PIN 0.079 SINGLE ROW SULLINS, NRPN031PAEN-RC
18 0 JP5 JUMPER, 2PINS, .079 CTR, OPTION OPTION
19 0 J1 CON.,MMCX, RIGHT ANGLE, THRU-HOLE, OPTION AMPHENOL CONNEX, 262105
20 1 J2 CON., SMA 50Ω EDGE-LAUNCH AMPHENOL CONNEX, 132372
21 2 J3, J4 CON.,SMA JACK, STRAIGHT, THRU-HOLE AMPHENOL CONNEX, 132134
22 0 L2 INDUCTOR, OPTION, 0603 OPTION
23 1 L3 FERRITE BEAD, 47ΩS@100mhz, 0603 MURATA, BLM18BB470SN1D
24 1 P1 BGA CONNECTOR, 40X10 SAMTEC, SEAM-40-02.0-S-10-2-A-K-TR
25 6 R1, R6, R7, R8, R14, R17 RES., CHIP, 1k, 1/16W, 5% 0402 VISHAY, CRCW04021K00JNED
26 1 R2, R9, R10 RES., CHIP, 0ΩS JUMPER, 1/16W, 0402 VISHAY, CRCW04020000Z0ED
27 3 R3, R4, R5 RES., CHIP, 4.99k, 1/16W, 1% 0402 VISHAY, CRCW04024K99FKED
28 2 R11, R12 RES., CHIP, 33.2ΩS, 1/16W, 1% 0402 VISHAY, CRCW040233R2FKED
29 2 R15, R16 RES., CHIP, 100ΩS, 1/16W, 5% 0402 VISHAY, CRCW0402100RJNED
30 0 R18, R20, R23 RES., CHIP, OPT, 0402 OPTION
31 1 R21 RES., CHIP, 49.9ΩS, 1/8W, 1% 0402 VISHAY, CRCW040249R9FKEDHP
32 0 R22 RES., CHIP, OPT, 0603 OPTION
33 4 R24, R29, R30, R31 RES., CHIP, 33ΩS, 1/16W, 5% 0402 VISHAY, CRCW040233R0JNED
34 0 R25 RES., CHIP, OPT, 0805 OPTION
35 2 R34, R36 RES., CHIP, 24.9ΩS, 1/16W, 1% 0402 VISHAY, CRCW040224R9FKED
36 1 R37 RES., CHIP, 200Ω, 1/20W, 1% 0201 VISHAY, CRCW0201200RFKED
37 2 T1, T3 TRANSFORMER, RF,SMT, 1:1BALUN MACOM, MABA-007159-000000
38 1 T2 TRANSFORMER, RF 1:1 FLUX COUPLED, SMT MACOM, MABAES0060
39 1 U2 IC, LDO LINEAR REGULATOR, 2.5V, DFN LINEAR TECH., LT1965EDD-2.5#PBF
40 1 U3 IC, LDO LINEAR REGULATOR, 1.8V, DFN LINEAR TECH., LT1965EDD-1.8#PBF
41 1 U4 IC, SERIAL EEPROM, TSSOP MICROCHIP TECH., 24LC32A-I/ST
42 7 XJP1, XJP2, XJP3, XJP4,
XJP5, XJP6, XJP7
SHUNT, 2MM SAMTEC, 2SN-BK-G
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

9
dc2183af
DEMO MANUAL DC2183A
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER
DC2183A-A Required Circuit Components
1 1 DC2183A DC2183A General BOM
2 1 C8 CAP., NP0, 4.7pF, 50V ± 0.25pF, 0402 TDK, C1005C0G1H4R7C
3 2 C9,C10 CAP., NP0, 8.2pF, 50V ± 0.25pF 0402 TDK, C1005C0G1H8R2C
4 1 L1 INDUCTOR, CERAMIC CHIP, 56nH, 2%, 0603 MURATA, LQP18MN56NG02D
5 2 R13,R19 RES., CHIP, 15Ω, 1/20W, 5% 0201 VISHAY, CRCW020115R0JNED
6 0 R26,R28 RES., CHIP, OPT, 0402 OPTION
7 2 R27,R32 RES., CHIP, 86.6, 1/10W, 1% 0603 VISHAY, CRCW060386R6FKEA
8 1 R33 RES., CHIP, 86.6, 1/16W, 1% 0402 VISHAY, CRCW040286R6FKED
9 1 U1 ADC, 16 BIT, 210 Msps, QFN LINEAR TECH., LTC2107IUK#PBF
DC2183A-B Required Circuit Components
1 1 DC2183A DC2183A General BOM
2 1 C8 CAP., NP0, 12pF, 50V 5% 0402 MURATA, GRM1555C1H120JA01D
3 2 C9,C10 CAP., NP0, 3.9pF, 50V ± 0.25pF 0402 TDK, C1005C0G1H3R9C
4 1 L1 INDUCTOR, CERAMIC CHIP, 18nH, 2%, 0603 MURATA, LQP18MN18NG02D
5 2 R13,R19 RES., CHIP, 10Ω, 1/20W, 5% 0201 VISHAY, CRCW020110R0JNED
6 2 R26,R28 RES., CHIP, 68.1Ω, 1/16W, 1% 0402 VISHAY, CRCW040268R1FKED
7 2 R27,R32 RES., CHIP, 43.2, 1/10W, 1% 0603 VISHAY, CRCW060343R2FKEA
8 1 R33 RES., CHIP, 105Ω, 1/16W, 1% 0402 VISHAY, CRCW0402105RFKED
9 1 U1 ADC, 16 BIT, 210 Msps, QFN LINEAR TECH., LTC2107IUK#PBF
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

10
dc2183af
DEMO MANUAL DC2183A
schematic Diagram
Figure 5. DC2183A Demo Circuit Schematic, Page 1
5
5
4
4
3
3
2
2
1
1
D
D
C
C
B
B
A
A
EXT REF
3/2
1X
ON
OFF
SHUTDOWN
SHDN
RUN
PGA
RAND
CMOS
LVDS PAR
SER
CLK+
CLK-
03-18-2014
-
SDO
CML
LVDS
LV PECL
CLOCK TERM
AIN
ASSEMBLY TYPE U1
DC2183A-A
DC2183A-B
BITS
16
16
12pF
4.7pF
C8 C9,C10
8.2pF
3.9pF
L1
56nH
18nH
R27,R32
86.6
43.2 105
86.6
R33
Msps
210
210
LTC2107IUK
LTC2107IUK
ASSEMBLY OPTIONS TABLE
*
R26,R28
OPT 68.1
R19,R13
15 10
*
*
*
*
*
*
OF+
OF-
Fin (MHz)
5< Fin <70
70< Fin <180
PAR/!SER
SHDN
SHDN PAR/!SER
OVDD
VDD
OVDD
VDD VDD VDD
VDD
VDD
VDD
OVDD
CS/LVDS
RAND/SDIPGA/SCK
D9/8+ D9/8- D7/6+ D7/6- D15/14+ D15/14- D3/2+ D3/2- D13/12+ D13/12- D1/0+ D1/0- D5/4+ D5/4- D11/10+ D11/10-
PGA/SCK RAND/SDI CS/LVDS
SDO
CLKOUT+ CLKOUT- OF- OF+
SIZE DATE:
IC NO.
REV
SHEET OF
TITLE:
CONTRACT NO.
APPROVALS
PCB DES.
ENG.
TECHNOLOGY
Fax: [phone] Milpitas, CA 95035
Phone: [phone]
1630 McCarthy Blvd.
LTC Confidential-For Customer Use Only
CUSTOMER NOTICE
LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A
CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS;
HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO
VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL
APPLICATION. COMPONENT SUBSTITUTION AND PRINTED
CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE OR RELIABILITY. CONTACT LINEAR
TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE.
THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND
SCHEMATIC
SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS.
2
1 2
16-BIT, 210 Msps ADC
M.HAWKINS
C.MAYOTT
A
LTC2107
DEMO CIRCUIT 2183A
SIZE DATE:
IC NO.
REV
SHEET OF
TITLE:
CONTRACT NO.
APPROVALS
PCB DES.
ENG.
TECHNOLOGY
Fax: [phone] Milpitas, CA 95035
Phone: [phone]
1630 McCarthy Blvd.
LTC Confidential-For Customer Use Only
CUSTOMER NOTICE
LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A
CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS;
HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO
VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL
APPLICATION. COMPONENT SUBSTITUTION AND PRINTED
CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE OR RELIABILITY. CONTACT LINEAR
TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE.
THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND
SCHEMATIC
SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS.
2
1 2
16-BIT, 210 Msps ADC
M.HAWKINS
C.MAYOTT
A
LTC2107
DEMO CIRCUIT 2183A
SIZE DATE:
IC NO.
REV
SHEET OF
TITLE:
CONTRACT NO.
APPROVALS
PCB DES.
ENG.
TECHNOLOGY
Fax: [phone] Milpitas, CA 95035
Phone: [phone]
1630 McCarthy Blvd.
LTC Confidential-For Customer Use Only
CUSTOMER NOTICE
LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A
CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS;
HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO
VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL
APPLICATION. COMPONENT SUBSTITUTION AND PRINTED
CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE OR RELIABILITY. CONTACT LINEAR
TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE.
THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND
SCHEMATIC
SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS.
2
1 2
16-BIT, 210 Msps ADC
M.HAWKINS
C.MAYOTT
A
LTC2107
DEMO CIRCUIT 2183A
REVISION HISTORY DESCRIPTION DATEAPPROVEDECO REV
C.MAYOTT
PRODUCTION2 03-14-14
REVISION HISTORY DESCRIPTION DATEAPPROVEDECO REV
C.MAYOTT
PRODUCTION2 03-14-14
REVISION HISTORY DESCRIPTION DATEAPPROVEDECO REV
C.MAYOTT
PRODUCTION2 03-14-14
C30 OPT C30 OPT
C29 0.1uF C29 0.1uF
R2 0 OHMSR2 0 OHMS
C27
2200pF
COG/NPO
C27
2200pF
COG/NPO
R13 0201 R13 0201
C22
1.0uF
C22
1.0uF
C25
10uF
0805
C25
10uF
0805
C6
0.01uF
C6
0.01uF
C10 *C10 *
C18 OPT
0402
C18 OPT
0402
J1 MMCX (OPTION)J1 MMCX (OPTION)
1
E1E1
J3J3
1
R23 OPT R23 OPT
JP1JP1
1 3 5 6
4 2
R32 * R32 *
C11 0.1uF C11 0.1uF
C9 *C9 *
C31 0.01uF C31 0.01uF
R16 100R16 100
JP2JP2
1 3 5 6
4 2
R9 0 R9 0
TP1TP1
1
J4J4
1
R22
OPT
R22
OPT
R37 200
0201
R37 200
0201
R36 24.9 R36 24.9
C14 0.1uF C14 0.1uF
L2 OPT
0603
L2 OPT
0603
1 2
C3 1.0uF C3 1.0uF
C28 OPT
0201
C28 OPT
0201
C17 2.2uF C17 2.2uF
R27 * R27 *
JP5
OPT
JP5
OPT
12
JP6JP6
1 3 5 6
4 2
R6 1K R6 1K
R12
33.2
R12
33.2
C5
0.01uF
C5
0.01uF
R14 1K R14 1K
R11
33.2
R11
33.2
R21 49.9 R21 49.9
R20 OPT R20 OPT
C8C8
C1
0.1uF
C1
0.1uF
C12 0.1uF C12 0.1uF
R33R33
R1 1KR1 1K
R7 1K R7 1K
C26
2200pF
COG/NPO
C26
2200pF
COG/NPO
C13 2.2uF C13 2.2uF
R26R26
T1
MABA-007159-000000
T1
MABA-007159-000000
5 4 3
1 2
R34 24.9 R34 24.9
R18 OPTR18 OPT
R10 0 R10 0
R8 1KR8 1K
J2J2
1
C7 0.01uF C7 0.01uF
R19 0201 R19 0201
C21 47uF
20%
1206
C21 47uF
20%
1206
T3
MABA-007159-000000
T3
MABA-007159-000000
5 4 3
1 2
R15 100R15 100
R28R28
JP3JP3
1
2
3
R17 1K R17 1K
T2
MABAES0060
T2
MABAES0060
5 4 3
1 2
C15 0.1uF C15 0.1uF
L1 * L1 *
1 2
*
U1
*
U1
SENSE
1
GND
2
GND
3
VDD
4
VDD
5
VDD
6
GND
7
AIN+
8
AIN-
9
GND
10
VCM
11
GND
12
GND
13
ENC+
14
ENC-
15
GND
16
SHDN
17
SDO
18
OGND
19
OVdd
20
D1/D0N
21
D1/D0P
22
D3/D2N
23
D3/D2P
24
D5/D4N
25
D5/D4P
26
D7/6N
27
D7/6P
28
D9/8N
29
D9/8P
30
CLKOUTN
31
CLKOUTP
32
D11/D10N
33
D11/10P
34
D13/12N
35
D13/12P
36
D15/14N
37
D15/14P
38
OFN
39
OFP
40
OVDD
41
OGND
42
SDI
43
SCK
44
CS
45
PAR/SER
46
GND
47
GND
48
GND
49
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

11
dc2183af
DEMO MANUAL DC2183A
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-
tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
schematic Diagram
Figure 6. DC2183A Demo Circuit Schematic, Page 2
5
5
4
4
3
3
2
2
1
1
D
D
C
C
B
B
A
A
DATA CLOCK
03-18-2014
GND
VIN
3.3V-5V
PROG
EEPROM
WP
TRANSFER STRIP
MOUNTING HOLES ON THERMAL
CHASSIS GROUND
3.3V_AUX
VIN
SCL SDA
3.3V_AUX
VIN
VDD
VDD OVDD
SCL SDA
D3/2+ D3/2-
D13/12+ D13/12- D1/0+ D1/0- D5/4+ D5/4-
D11/10+ D11/10- D9/8-
RAND/SDI PGA/SCK CS/LVDS SDO
D15/14+ D15/14-
D7/6-
D7/6+
D9/8+
CLKOUT- CLKOUT+
SCL SDA
OF-
OF+
SIZE DATE:
IC NO.
REV
SHEET OF
TITLE:
CONTRACT NO.
APPROVALS
PCB DES.
ENG.
TECHNOLOGY
Fax: [phone] Milpitas, CA 95035
Phone: [phone]
1630 McCarthy Blvd.
LTC Confidential-For Customer Use Only
CUSTOMER NOTICE
LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A
CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS;
HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO
VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL
APPLICATION. COMPONENT SUBSTITUTION AND PRINTED
CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE OR RELIABILITY. CONTACT LINEAR
TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE.
THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND
SCHEMATIC
SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS.
2
22
16-BIT, 210 Msps ADC
M.HAWKINS
C.MAYOTT
A
LTC2107
DEMO CIRCUIT 2183A
SIZE DATE:
IC NO.
REV
SHEET OF
TITLE:
CONTRACT NO.
APPROVALS
PCB DES.
ENG.
TECHNOLOGY
Fax: [phone] Milpitas, CA 95035
Phone: [phone]
1630 McCarthy Blvd.
LTC Confidential-For Customer Use Only
CUSTOMER NOTICE
LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A
CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS;
HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO
VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL
APPLICATION. COMPONENT SUBSTITUTION AND PRINTED
CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE OR RELIABILITY. CONTACT LINEAR
TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE.
THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND
SCHEMATIC
SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS.
2
22
16-BIT, 210 Msps ADC
M.HAWKINS
C.MAYOTT
A
LTC2107
DEMO CIRCUIT 2183A
SIZE DATE:
IC NO.
REV
SHEET OF
TITLE:
CONTRACT NO.
APPROVALS
PCB DES.
ENG.
TECHNOLOGY
Fax: [phone] Milpitas, CA 95035
Phone: [phone]
1630 McCarthy Blvd.
LTC Confidential-For Customer Use Only
CUSTOMER NOTICE
LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A
CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS;
HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO
VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL
APPLICATION. COMPONENT SUBSTITUTION AND PRINTED
CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE OR RELIABILITY. CONTACT LINEAR
TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE.
THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND
SCHEMATIC
SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS.
2
22
16-BIT, 210 Msps ADC
M.HAWKINS
C.MAYOTT
A
LTC2107
DEMO CIRCUIT 2183A
P1J
SEAM-10X40PIN
P1J
SEAM-10X40PIN
GND
J1
CLK1_C2M_P
J2
CLK1_C2M_N
J3
GND
J4
GND
J5
HA03_P
J6
HA03_N
J7
GND
J8
HA07_P
J9
HA07_N
J10
GND
J11
HA11_P
J12
HA11_N
J13
GND
J14
HA14_P
J15
HA14_N
J16
GND
J17
HA18_P
J18
HA18_N
J19
GND
J20
HA22_P
J21
HA22_N
J22
GND
J23
HB01_P
J24
HB01_N
J25
GND
J26
PB07_P
J27
HB07_N
J28
GND
J29
HB11_P
J30
HB11_N
J31
GND
J32
HB15_P
J33
HB15_N
J34
GND
J35
HB18_P
J36
HB18_N
J37
GND
J38
VIO_B_M2C
J39
GND
J40
R31 33R31 33
X1X1
E3E3
P1E
SEAM-10X40PIN
P1E
SEAM-10X40PIN
GND
E1
HA01_P_CC
E2
HA01_N_CC
E3
GND
E4
GND
E5
HA05_P
E6
HA05_N
E7
GND
E8
HA09_P
E9
HA09_N
E10
GND
E11
HA13_P
E12
HA13_N
E13
GND
E14
HA16_P
E15
HA16_N
E16
GND
E17
HA20_P
E18
HA20_N
E19
GND
E20
HB03_P
E21
HB03_N
E22
GND
E23
HB05_P
E24
HB05_N
E25
GND
E26
HB09_P
E27
HB09_N
E28
GND
E29
HB13_P
E30
HB13_N
E31
GND
E32
HB21_P
E33
HB21_N
E34
GND
E35
HB20_P
E36
HB20_N
E37
GND
E38
VADJ
E39
GND
E40
C16 10uF
16V
1206
C16 10uF
16V
1206
X16X16
P1A SEAM-10X40PIN P1A SEAM-10X40PIN
GND
A1
DP1_M2C_P
A2
DP1_M2C_N
A3
GND
A4
GND
A5
DP2_M2C_P
A6
DP2_M2C_N
A7
GND
A8
GND
A9
DP3_M2C_P
A10
DP3_M2C_N
A11
GND
A12
GND
A13
DP4_M2C_P
A14
DP4_M2C_N
A15
GND
A16
GND
A17
DP5_M2C_P
A18
DP5_M2C_N
A19
GND
A20
GND
A21
DP1_C2M_P
A22
DP1_C2M_N
A23
GND
A24
GND
A25
DP2_C2M_P
A26
DP2_C2M_N
A27
GND
A28
GND
A29
DP3_C2M_P
A30
DP3_C2M_N
A31
GND
A32
GND
A33
DP4_C2M_P
A34
DP4_C2M_N
A35
GND
A36
GND
A37
DP5_C2M_P
A38
DP5_C2M_N
A39
GND
A40
U3
LT1965EDD-1.8
U3
LT1965EDD-1.8
OUT
2
IN
7
SENSE
3
IN
8
OUT
1
GND
9
SHDN
6
GND
4
GND
5
C2 100uF
16V
1210
C2 100uF
16V
1210
X12X12
C4 100uF
16V
1210
C4 100uF
16V
1210
R5 4.99K R5 4.99K
P1K
SEAM-10X40PIN
P1K
SEAM-10X40PIN
VREF_B_M2C
K1
GND
K2
GND
K3
CLK1_M2C_P
K4
CLK1_M2C_N
K5
GND
K6
HA02_P
K7
HA02_N
K8
GND
K9
HA06_P
K10
HA06_N
K11
GND
K12
HA10_P
K13
HA10_N
K14
GND
K15
HA17_P_CC
K16
HA17_N_CC
K17
GND
K18
HA21_P
K19
HA21_N
K20
GND
K21
HA23_P
K22
HA23_N
K23
GND
K24
HB00_P_CC
K25
HB00_N_CC
K26
GND
K27
HB06_P_CC
K28
HB06_N_CC
K29
GND
K30
HB10_P
K31
HB10_N
K32
GND
K33
HB14_P
K34
HB14_N
K35
GND
K36
HB17_P_CC
K37
HB17_N_CC
K38
GND
K39
VIO_B_M2C
K40
X10X10 X8X8
P1F
SEAM-10X40PIN
P1F
SEAM-10X40PIN
PG_M2C
F1
GND
F2
GND
F3
HA00_P_CC
F4
HA00_N_CC
F5
GND
F6
HA04_P
F7
HA04_N
F8
GND
F9
HA08_P
F10
HA08_N
F11
GND
F12
HA12_P
F13
HA12_N
F14
GND
F15
HA15_P
F16
HA15_N
F17
GND
F18
HA19_P
F19
HA19_N
F20
GND
F21
HB02_P
F22
HB02_N
F23
GND
F24
HB04_P
F25
HB04_N
F26
GND
F27
HB08_P
F28
HB08_N
F29
GND
F30
HB12_P
F31
HB12_N
F32
GND
F33
HB16_P
F34
HB16_N
F35
GND
F36
HB19_P
F37
HB19_N
F38
GND
F39
VADJ
F40
C24 10uF
16V
1206
C24 10uF
16V
1206
X6X6
P1B
SEAM-10X40PIN
P1B
SEAM-10X40PIN
RES1
B1
GND
B2
GND
B3
DP9_M2C_P
B4
DP9_M2C_N
B5
GND
B6
GND
B7
DP8_M2C_P
B8
DP8_M2C_N
B9
GND
B10
GND
B11
DP7_M2C_P
B12
DP7_M2C_N
B13
GND
B14
GND
B15
DP6_M2C_P
B16
DP6_M2C_N
B17
GND
B18
GND
B19
GBTCLK1_M2C_P
B20
GBTCLK1_M2C_N
B21
GND
B22
GND
B23
DP9_C2M_P
B24
DP9_C2M_N
B25
GND
B26
GND
B27
DP8_C2M_P
B28
DP8_C2M_N
B29
GND
B30
GND
B31
DP7_C2M_P
B32
DP7_C2M_N
B33
GND
B34
GND
B35
DP6_C2M_P
B36
DP6_C2M_N
B37
GND
B38
GND
B39
RES0
B40
C23 0.1uF C23 0.1uF
X14X14
U2
LT1965EDD-2.5
U2
LT1965EDD-2.5
OUT
2
IN
7
SENSE
3
IN
8
OUT
1
GND
9
SHDN
6
GND
4
GND
5
X4X4
C20 10uF
16V
1206
C20 10uF
16V
1206
X2X2
JP4JP4
1
2
3
R29 33R29 33
R25 OPT R25 OPT
U4
24LC32A
U4
24LC32A
A0
1
A1
2
A2
3
VSS
4
SDA
5
SCL
6
WP
7
VCC
8
P1G SEAM-10X40PIN P1G SEAM-10X40PIN
GND
G1
CLK0_C2M_P
G2
CLK0_C2M_N
G3
GND
G4
GND
G5
LA00_P_CC
G6
LA00_N_CC
G7
GND
G8
LA03_P
G9
LA03_N
G10
GND
G11
LA08_P
G12
LA08_N
G13
GND
G14
LA12_P
G15
LA12_N
G16
GND
G17
LA16_P
G18
LA16_N
G19
GND
G20
LA20_P
G21
LA20_N
G22
GND
G23
LA22_P
G24
LA22_N
G25
GND
G26
LA25_P
G27
LA25_N
G28
GND
G29
LA29_P
G30
LA29_N
G31
GND
G32
LA31_P
G33
LA31_N
G34
GND
G35
LA33_P
G36
LA33_N
G37
GND
G38
VADJ
G39
GND
G40
P1C
SEAM-10X40PIN
P1C
SEAM-10X40PIN
GND
C1
DP0_C2M_P
C2
DP0_C2M_N
C3
GND
C4
GND
C5
DP0_M2C_P
C6
DP0_M2C_N
C7
GND
C8
GND
C9
LA06_P
C10
LA06_N
C11
GND
C12
GND
C13
LA10_P
C14
LA10_N
C15
GND
C16
GND
C17
LA14_P
C18
LA14_N
C19
GND
C20
GND
C21
LA18_P_CC
C22
LA18_N_CC
C23
GND
C24
GND
C25
LA27_P
C26
LA27_N
C27
GND
C28
GND
C29
SCL
C30
SDA
C31
GND
C32
GND
C33
GA0
C34
12P0V
C35
GND
C36
12P0V
C37
GND
C38
3P3V
C39
GND
C40
R3 4.99K R3 4.99K
E2E2
X11X11
L3
FERRITE BEAD, 47 OHMS
L3
FERRITE BEAD, 47 OHMS
P1H
SEAM-10X40PIN
P1H
SEAM-10X40PIN
VREF_A_M2C
H1
PRSNT_M2C_N
H2
GND
H3
CLK0_M2C_P
H4
CLK0_M2C_N
H5
GND
H6
LA02_P
H7
LA02_N
H8
GND
H9
LA04_P
H10
LA04_N
H11
GND
H12
LA07_P
H13
LA07_N
H14
GND
H15
LA11_P
H16
LA11_N
H17
GND
H18
LA15_P
H19
LA15_N
H20
GND
H21
LA19_P
H22
LA19_N
H23
GND
H24
LA21_P
H25
LA21_N
H26
GND
H27
LA24_P
H28
LA24_N
H29
GND
H30
LA28_P
H31
LA28_N
H32
GND
H33
LA30_P
H34
LA30_N
H35
GND
H36
LA32_P
H37
LA32_N
H38
GND
H39
VADJ
H40
X13X13
X9X9
P1D
SEAM-10X40PIN
P1D
SEAM-10X40PIN
PG_C2M
D1
GND
D2
GND
D3
GBTCLK0_M2C_P
D4
GBTCLK0_M2C_N
D5
GND
D6
GND
D7
LA01_P_CC
D8
LA01_N_CC
D9
GND
D10
LA05_P
D11
LA05_N
D12
GND
D13
LA09_P
D14
LA09_N
D15
GND
D16
LA13_P
D17
LA13_N
D18
GND
D19
LA17_P_CC
D20
LA17_N_CC
D21
GND
D22
LA23_P
D23
LA23_N
D24
GND
D25
LA26_P
D26
LA26_N
D27
GND
D28
TCK
D29
TDI
D30
TDO
D31
3P3VAUX
D32
TMS
D33
TRST_N
D34
GA1
D35
3P3V
D36
GND
D37
3P3V
D38
GND
D39
3P3V
D40
X7X7
R24 33R24 33
R4 4.99K R4 4.99K
X15X15
X5X5 X3X3
R30 33R30 33
C19 10uF
16V
1206
C19 10uF
16V
1206
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

12
dc2183af
DEMO MANUAL DC2183A
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
[phone] ●FAX: [phone] ● www.linear.com  LINEAR TECHNOLOGY CORPORATION 2014
LT 0714 • PRINTED IN USA
DEMONSTRATION BOARD IMPORTANT NOTICE
Linear Technology Corporation (LTC) provides the enclosed product(s) under the following AS IS conditions:
This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT
OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete
in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety
measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union
directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations.
If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date
of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR
ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LTC from all claims
arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all
appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or
agency certified (FCC, UL, CE, etc.).
No License is granted under any patent right or other intellectual property whatsoever. LTC assumes no liability for applications assistance,
customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind.
LTC currently services a variety of customers for products around the world, and therefore this transaction is not exclusive.
Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and
observe good laboratory practice standards. Common sense is encouraged.
This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LTC application
engineer.
Mailing Address:
Linear Technology
1630 McCarthy Blvd.
Milpitas, CA 95035
Copyright © 2004, Linear Technology Corporation
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.