Linear HDMI-MX-4x4 User manual

4X4 Matrix For HDMI
Model # HDMI-MX-4X4
USER MANUAL
www.linearcorp.com

ASKING FOR ASSISTANCE
Technical Support:
Telephone [phone]
[phone]
Fax [phone]
Technical Support Hours:
6:30 AM - 4:30 PM PST Monday through Friday.
Email:
[email protected]
Website:
www.linearcorp.com
Notice
Linear LLC reserves the right to make changes in the hardware, packaging
and any accompanying documentation without prior written notice.
© 2008 Linear LLC, All Rights Reserved

TABLE OF CONTENTS
Introduction / Operation Notes1.
Features2.
Panel Descriptions3.
Connecting And Operating the 4X4 Matrix For HDMI4.
RMT-16IR Remote Control Installation5.
IR Code Conguration6.
RS-232 Serial Control Interface7.
Rack Ears Installation Diagram8.
Wiring Diagram9.
Specications10.
Warranty11.

HDMI/HDCP Compliant•
Compatible with all HDMI and DVI* displays•
Display information (EDID) is sent from the display connected to HDMI Output• Port 1 to all sources connected to the 4X4 Matrix for HDMI. If a DVI display is
connected to HDMI Output Port 1, the remaining HDMI Output Ports will be
scanned in succession for an EDID from an HDMI display to use. If all displays
connected to the 4X4 Matrix for HDMI are DVI displays, the EDID from the DVI
display connected to HDMI Output Port 1 is used.
Switching a display to a different source may cause all other displays•
currently viewing that source to momentarily icker. This is caused by syncing/
handshaking operations.
NOTE: *When used with a HDMI to DVI adapter
The Linear 4x4 Matrix for HDMI allows maximum versatility and exibility for creating
an integrated HD system. The 4x4 matrix routes digital audio and high denition digital
video in resolutions up to 1080p from any of four HDMI sources to any combination
of four displays through the matrix. It works with Blu-Ray / HD-DVD players, TiVo
systems, Home Theater PCs, Satellite and Cable Set Top Boxes that can connect to
anHDMIdisplay. Each source is accessible for viewing on any combination of displays
by selecting it with the supplied IR remote.
How It Works
You simply connect the sources to the Matrix’s HDMI inputs. Then connect four
displays to the Matrix’s outputs. Once the sources, the matrix, and the displays are
powered and connected, you use the IR remote to select which sources you want to
view on which displays.
INTRODUCTION
1
READ THESE NOTES BEFORE INSTALLING OR
OPERATING THE 4X4 MATRIX FOR HDMI
OPERATION NOTES

FEATURES
Features
Switch easily between any four HDMI sources•
Distributes any of the four inputs to any combination of the four HDMI output• displays
Supports resolutions up to 1080p, 2K and 1920 x 1200•
Extends the range of HDMI compliant devices by equalizing and reclocking the•
HDMI signal•
HDMI/HDCP compliant•
Includes:
(1) 4x4 Matrix For HDMI
(4) HDMI 6 Ft Cables (M-M)
(1) 24V DC Power Supply
(1) User Manual
(1) RMT-16IR Remote Control
(1) Set Of Rack Ears
NOTE: *When used with a HDMI to DVI adapter
2

PANEL DESCRIPTIONS
Display 1
LED Indicator
Front Panel
RS-232 Serial Control
Interface
Display 2
LED Indicator Display 3
LED Indicator Display 4
LED Indicator
IR Sensor
IR Extender Eye Port Power LED
Indicator
Back Panel
24V DC Power
Input
HDMI Inputs*
*See note on page 4 for additional information
HDMI Outputs
3

CONNECTING THE 4X4 MATRIX FOR HDMI
OPERATING THE 4X4 MATRIX FOR HDMI
4
Connect the HDMI/DVI* sources (up to four) to the 4X4 Matrix For HDMI using the1. supplied HDMI cables.
Connect the HDMI/DVI* displays (up to four) to the2. 4X4 Matrix For HDMI using user
supplied HDMI cables.
Plug the included 24V DC power supply into the3. 4X4 Matrix For HDMI.
Power on the displays.4.
Power on the sources. When powering on each source, please ensure that it is sending5. video to a connected and powered on display.
*When used with a HDMI to DVI adapter
NOTE: Display information (EDID) is sent from the display connected to HDMI Output Port
1 to all sources connected to the 4X4 Matrix for HDMI. If a DVI display is connected to
HDMI Output Port 1, the remaining HDMI Output Ports will be scanned in succession for an
EDID from an HDMI display to use. If all displays connected to the 4X4 Matrix for HDMI are
DVI displays, the EDID from the DVI display connected to HDMI Output Port 1 is used.
The 4X4 Matrix For HDMI switching can be controlled by either the included RMT-16IR remote
control or by the RS-232 serial control interface on the rear of the unit.
IR Remote Control
The supplied RMT-16IR remote control has 16 buttons control which HDMI source is being
routed to the 4 display output ports. Please use the table below for the IR remote control table.
RMT-16IR
Button HDMI Display Output Port Connects to HDMI Input Port
1 1 1
2 1 2
3 1 3
4 1 4
5 2 1
6 2 2
7 2 3
8 2 4
9 3 1
10 3 2
11 3 3
12 3 4
13 4 1
14 4 2
15 4 3
16 4 4
RS-232 Serial Control
Please see page 7 for information
on using the RS-232 serial control
interface

RMT-16IR REMOTE CONTROL INSTALLATION
5
Remove battery cover from the back of the RMT-16IR remote.1.
Verify that dip switches 1 & 2 are in the down (OFF) position. (see next page)2.
Insert the battery, hold the battery so that you can see the positive side facing3. up. The side that is not marked must be facing down.
Test the RMT-16IR remote by pressing ONLY one button at a time. The4.
indicator light on the remote will ash once each time you press a button.
WARNING:
Do not press multiple buttons simultaneously and do NOT press buttons rapidly.
These actions will cause the remote to reset and steps 1-4 will have to be repeated.
Note: The RMT-16IR ships with two batteries. Only one battery is required for
operation, the other battery is complimentary.
The optional IR extender allows you to
relocate your HDMI Switcher and still retain IR
control. Linear part# IR-EXTENDER

IR CODE CONFIGURATION
4X4 Matrix for HDMI
Remote Channel 1:
Default
Remote Channel 4:
Remote
Remote Channel 1:
Default
1 2
Remote Channel 2:
1 2
Remote Channel 3:
1 2
Remote Channel 4:
1 2
How to Resolve IR Code Conicts
In the event that IR commands from other remote controls conict with the supplied RMT-16IR
remote control, changing the remote channel will alleviate this issue. The RMT-16IR remote
control and the 4X4 Matrix for HDMI have DIP SWITCHES for conguring the remote channel
that both units use to communicate. These settings must match each other for proper operation.
The 2 DIP SWITCH bank on the RMT-16IR is located underneath the battery cover. The 8 DIP
SWITCH bank for the 4X4 Matrix For HDMI is located inside of the unit. *DIP SWITCH 1 and 2 on
the RMT16-IR correspond to DIP SWITCH 3 and 4 on the 4x4 Matrix For HDMI.
NOTE: *DIP SWITCHES 1, 2, and 5 through 8 are not used on the 4X4 Matrix for HDMI.
Because the procedure for changing channels requires the main unit to be disassembled, this
procedure should only be done if there are IR conicts present in your setup.
Disconnect power from unit before starting. Remove all cabling from unit. To open the 4X4 Matrix
for HDMI Unit, remove all screws from the sides and underside of the unit. Remove the hex nuts
above each HDMI connector and on the RS-232 serial connector. Slide the unit apart carefully to
expose the internal PCB and the 8 DIP SWITCH bank.
When DIP SWITCH adjustments are complete, carefully slide the unit back together. Being careful
not to over tighten the hex nuts, screw them back in above each HDMI connector and on the RS-
232 serial connector. Screw all of the screws from the sides and underside of the unit back into the
unit, again being careful not to over tighten the screws. Plug all cabling back into its proper location
on the unit. Reconnect power to the unit and test for IR conicts.
6
12345678
Remote Channel 3:
12345678
Remote Channel 2:
12345678
12345678

RS-232 SERIAL CONTROL INTERFACE
7
Binary Table
ASCII Corresponding
RMT16-IR
Button
Binary ASCII Corresponding
RMT16-IR
Button
Binary
1 1 0011 0001 9 9 0011 1001
2 2 0011 0010 a 10 0110 0001
3 3 0011 0011 b 11 0110 0010
4 4 0011 0100 c 12 0110 0011
5 5 0011 0101 d 13 0110 0100
6 6 0011 0110 e 14 0110 0101
7 7 0011 0111 f 15 0110 0110
8 8 0011 1000 g 16 0110 0111
Terminal Settings
Bits per second ................................................................................................. 19200
Data bits .................................................................................................................... 8
Parity .................................................................................................................. None
Stop bits .....................................................................................................................1
Flow Control ....................................................................................................... None
1 2 3 4 5
6 7 8 9
1 2 3 4 5
6 7 8 9
Only Pins 2 (RX), 3 (TX), and 5 (Ground) are needed to operate RS-232 Interface

RACK EARS INSTALLATION DIAGRAM
8
Rear of unit
Front of unit
Rack mount ears are provided for installation of this unit into a 1U rack mount
space.
Locate the side screws on the unit.1. Remove the front 2 screws that are located closest to the front of the unit.2. Using the removed screws, screw the rack mounting bracket into the unit.3. Repeat the procedure on the opposite side of the unit.4.
1
2
3
4

WIRING DIAGRAM
9
Maximum HDMI cable length is 15 ft at 1080P resolution without the use of an HDMI-SB or HDMI-CAT5-EXT

10
SPECIFICATIONS
Video Amplier Bandwidth............................................................................. 165 MHz
Input Video Signal.................................................................................... 1.2 Volts p-p
Input DDC Signal............................................................................... 5 Volts p-p (TTL)
Single Link Range.......................................................................... 1080p/1920 x 1200
HDMI Connector.......................................................................... Type A 19 pin female
Remote Control Port.......................................................... RS232 female, mini-stereo
Power Consumption............................................................................. 60 Watts (max)
Dimensions........................................................................... 17”W x 1.75”H x 5.875”D
Rack Mountable..................................................................................... 1U rack space
Shipping Weight................................................................................................... 7 lbs.

11
Note: These products are designed to be installed and serviced by trained professional
installation companies.
Linear LLC warrants this product to be free from defects in material and workmanship. For the
term of the warranty, see the list of products below. The Warranty Expiration Date is reected by
a date code that is afxed to all of Linear’s products. This warranty extends only to wholesale
customers who buy direct from Linear or through Linear’s normal distribution channels. Linear
does not warrant this product to consumers. Consumers should inquire from their selling dealer
as to the nature of the dealer’s warranty. There are no obligations or liabilities on the part of
Linear LLC for consequential damages arising out of or in connection with use or performance
of this product or other indirect damages with respect to loss of property, revenue, or prot, or
cost of removal, installation or reinstallation. All implied warranties, including implied warranties
for merchantability and implied warranties for tness, are valid only until warranty expiration date
as labeled on the product. This Linear LLC Warranty is in lieu of all other warranties express or
implied. Some states and countries do not allow limitations or how long an implied warranty lasts
or the exclusion or limitation or incidental or consequential damages, so the above exclusions
may not apply. The Linear LLC warranty gives specic legal rights in addition to other rights,
which may exist and vary from state to state and country to country.
All products returned for warranty service require a Return Product Authorization Number (RPA#).
Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.
Consumers: If you have trouble locating your installing company, please contact Linear LLC at
1-800-421-1587 and we will assist you with locating a service and Installation Company.
The following warranty period applies to this set of Linear branded products.
Linear High Denition Video products — Two (2) years. There is no warranty offered on the 1. batteries supplied with the IR remote Control.
The warranty is limited to repair or replacement of products returned, freight prepaid, to
Linear LLC. There is NO PROVISION FOR LABOR COST OR OTHER REIMBURSEMENTS
OF ANY KIND.
Failures due to product abuse, negligence, improper installation, improper use, and1. electrical surge including damage from lightning, water damage or other damage due to
natural disasters are not covered by the warranty.
The warranty shall also be voided by any tampering with the date code, labels or other2. markings on the product.
Products that are damaged in transit to Linear LLC due to improper packaging or by the3. carrier (shipping company) will not be covered under the warranty. If the product was
damaged or lost by the carrier, it is the sender’s responsibility to create a claim against the
carrier.
The user is responsible for all labor costs associated with removing, reinstalling and4. returning the product to Linear LLC.
Linear LLC, at its option, will repair or replace the defective product.5.
Replacements will be made from B-Stock. If an exact replacement is not available Linear6. LLC, at its option will select the nearest equivalent product. The user is responsible for
freight charges to Linear LLC.
Linear LLC will return warranted repaired or replacements by UPS Ground or an equivalent7. service. Acustomer may pay the additional costs for second day or next-day service.
WARRANTY

Rev A
HDMI-MX-4X4
[phone]
[phone] FAX [phone]
www.linearcorp.com