Linksys EtherFast Instant Broadband BEFW11S4 Original operating instructions

A Division of Cisco Systems, Inc.
®
Model No.
Quick Installation
Model No.
Wireless
BEFW11S4
Broadband Router
Wireless-B
1
ABefore you begin, make sure
that you have the setup
information for your specific
type of Internet connection.
The installation technician from
your ISP should have left this
information with you after
installing your broadband
connection. If not, you can call
your ISP to request the settings.
BMake sure that all of your
network’s hardware is powered
off, including the Router, PCs,
and cable or DSL modem.
CConnect one end of an
Ethernet network cable to one
of the ports (labeled 1-4) on
the back of the Router, and the
other end to an Ethernet port
on a PC. (Figure C)
2
Connect the Broadband Router
These instructions will show you how
to configure the Router. You only
need to configure it once.
AOpen your web browser. Enter
http://192.168.1.1 in its Address
field. Press the Enter key. (Figure
A)
BA password request screen will
appear. Leave the User Name
field empty, and enter the
default password, admin, in
lowercase letters in the
Password field. (For added
security, you should later set a
new password, using the
Administration tab’s
Management screen of the
Web-based Utility). Then click
the OK button.
CThe Web-based Utility will
appear with the Setup tab
selected. If requested by your
ISP (usually cable ISPs),
complete the Host Name and
Domain Name fields.
Otherwise, leave them blank.
(Figure C)
C
Configure the Router
DRepeat step C to connect
additional PCs or other network
devices to the Router.
EConnect a different Ethernet
network cable from your cable
or DSL modem to the Internet
port on the Router’s back
panel. This is the only port that
will work for your modem
connection. (Figure E)
FPower on the cable or DSL
modem.
GConnect the AC power
adapter to the Router’s Power
port and the other end into an
electrical outlet. (Figure G)
HMake sure the Power and
Internet LEDs on the front panel
light up green.
IThe Power LED will flash green
for a few seconds when the
Router goes through its self-
diagnostic test. This LED will stay
solidly lit when the self-test is
complete. If it does not stop
flashing, refer to “Appendix A:
Troubleshooting” of the User
Guide on the Setup CD-ROM.
JPower on the PC you wish to
use to configure the Router.
Proceed to Step 2.
NOTE: Make sure your PC’s Ethernet
adapter is set to obtain an IP address
automatically. For more information,
refer to Windows Help.
IMPORTANT: Make sure you use
the power adapter that is supplied
with the Router. Use of a different
power adapter could damage the
Router.
There are two ways to configure the Router. Choose one of the following:
• Run the Setup CD-ROM - It is strongly recommended that you use the
Setup CD-ROM to install the Router. Insert the Setup CD-ROM into the
CD-ROM drive, and follow the on-screen instructions.
•Use this Quick Installation guide - If you wish, you can use the Router’s
web-based utility to install the Router. Proceed to Step 1, and follow the
Quick Installation’s instructions.
G
C
E
Package Contents
• Wireless-B Broadband Router
• Setup CD-ROM
• User Guide on CD-ROM
• Power Adapter
• Ethernet Network Cable
• Quick Installation Guide
• Registration Card
A
GHz
2.4
802.11b

connection, check with your ISP for
setup information. (D5)
HeartBeat Signal: HeartBeat Signal
is a service used in Australia only. If
you are using a HeartBeat Signal
connection, check with your ISP for
setup information. (D6)
EWhen you have finished
entering your Internet
connection settings, click the
Save Settings button to save
your changes.
FTo configure the Router for your
wireless network, select the
Wireless Tab’s Basic Wireless
Settings screen. (Figure F)
GWireless Network Name (SSID).
The SSID is the network name
shared among all devices in a
wireless network. The SSID must
be identical for all devices in
the wireless network. It is case-
sensitive and must not exceed
32 characters (use any
keyboard character). For
added security, you should
change the default SSID linksys
to a unique name.
HWireless Channel. Select the
appropriate channel from the
list provided to correspond with
your network settings. All
devices in your wireless network
must broadcast on the same
DFor the Internet Connection
Type setting, five connection
types are offered through the
drop-down menu. Each Setup
screen and available features
will differ depending on which
connection type you select.
Internet Configuration Type
DHCP: If you are connecting
through DHCP or a dynamic IP
address from your ISP, keep the
default setting Obtain an IP
Address Automatically. (D1)
Static IP: If your ISP assigns you a
static IP address, select Static IP
from the drop-down menu.
Complete the Internet IP Address,
Subnet Mask, Gateway, and Static
DNS fields. You need to enter at
least one DNS address. (D2)
PPPoE: If you are connecting
through PPPoE, select PPPoE from
the drop-down menu. Complete
the User Name and Password
fields. (D3)
RAS: (for SingTel Users) RAS is a
service used in Singapore only. If
you are using a RAS connection
check with your ISP for the
necessary setup information. (D4)
PPTP: PPTP is a service used in
Europe only. If you are using a PPTP
F
Configure the Broadband Router
channel in order to function
correctly.
IWireless SSID Broadcast. When
wireless clients survey the local
area for wireless networks to
associate with, they will detect
the SSID broadcast by the
Router. To broadcast the
Router's SSID, keep the default
setting, Enable. If you do not
want to broadcast the Router's
SSID, then select Disable.
JChange these settings as
described here and click the
Save Settings button to apply
your changes.
KPower your cable or DSL
modem off and back on
again.
LRestart your computer.
MTest the setup by opening your
web browser and entering
http://www.linksys.com/registration.
(Figure M)
Congratulations! The installation of
the Wireless-B Broadband Router
is complete.
BEFW11S4-v4-QI-31014NC BW
For additional information or troubleshooting
help, refer to the User Guide on the Setup CD-
ROM. You can also call or e-mail for further
support.
24-hour Technical Support
800-326-7114
(toll-free from US or Canada)
E-mail Support
[email protected]
Website
http://www.linksys.com or
http://support.linksys.com
RMA (Return Merchandise Authorization)
http://www.linksys.com/support
FTP Site
ftp://ftp.linksys.com
Sales Information
800-546-5797 (800-LINKSYS)
Linksys is a registered trademark or trademark of
Cisco Systems, Inc. and/or its affiliates in the U.S.
and certain other countries. Copyright © 2003
Cisco Systems, Inc. All rights reserved.
3
NOTE: For more advanced settings
and security options, refer to the
User Guide on the Setup CD-ROM.
D1
D2
D3
D4
M
D5
D6