Lisa 1DR User manual

INS LISA 1DR.vsd Created: 10-6-2017 Revised:10-6-2017 INS0000130-01 v1.0 Page 1
LISA 1DR (Standalone Door Alarm)
Packing List
Telescoping Sensor & Fasteners
1DR specific Power Supply/Controller/
Strobe Assembly x 1 each
# 8 Wood Screws
x 4 each 10-24 Carriage Bolt, Hex Nuts,
Washers & Lock Washers x 4 each
x 3/16" Pan Head Phillips Screws, #8 Washers x 2
each & Mounting Plate Spacer x 1 each Wire Harness x 1 each
Telescoping Sensor x 1 each
x ½Flat Head Security Screw x 2 each,
Cylindrical Locking Ring x 1 each & 1DR
specific alarm shunt keyswitch w/ surface
mounted box and armored cable x 1 each
#8 Wood Screws &
Plastic Anchors x 4
each
Top Portion
Bottom Portion
Full-Surface Continuous
Hinge x 1 each
12-24 x ½Torx Flat
Head Screw x 15 each #10-¾self Drilling Screw
X 4 each ¼ - 20 x 1" Torx Flat
Head Screw
x 9 each
¼ - 20 x 1-5/8" Sex Bolt
x 9 each
Allen Key
Ligature Resistant Hinge
(7) Armored Cable Straps
(14) Self
drilling
screws
Cylinder by others: 1-1/8" to 1-3/8" Cylinder,
Cloverleaf Cam Recommended

NOTE:
Door Sensors are provided to match the door width provided.
INSTALLATION INSTRUCTIONS:
FULL SURFACE CONTINUOUS HINGE
See Separate sheet provided for installation instructions.
POWER SUPPLY / CONTROLLER
• Install the Power Supply / Controller / Strobe in corridor outside room. 110vAC
connection required
• Power up the controller. All LEDs should turn green.
KEY SWITCH
• Add mortise cylinder (straight Yale cam) below Power Supply/ Controller.
• Mount gang box at door and run armored cable to power supply/controller.
• Fasten armored cable to wall with one armored cable strap approx every 12". (You
will have extra straps.)
• Connect wiring per wiring diagram. Key switch is NCsystem can not work without
it.
DOOR SENSOR
See Separate sheet provided for installation instructions. Note that additional sensors/
doors can be added in parallel (see wiring diagram)
A
B
D
A
B
C
D
C
INS LISA 1DR.vsd Created: 10-6-2017 Revised:10-6-2017 Page 2
LISA 1DR (Standalone Door Alarm)
Install Instructions

INS LISA 1DR.vsd Created: 10-6-2017 Revised:10-6-2017 Page 3
P1 & P2 = 1",
P0 = ¾
Door
Top edge of the door Frame 1-1/8"
Notched edge of the Hinge
Fig-1
Fig-2
Fig-1
Fig-2
Fig-3
Fig-3
Pilot Hole
Fig-4
Fig-4
Sensor Mounting Plate
First Mounting Hole
Door
Door
Self Tapping / Wood
Screws
Sensor Mounting Plate
Fig-5
Fig-5 Wiring Hole
3/8"-
7/16"
Door
Lock Edge of the Door
Fig-5
Slot Provided
Door
Cover screw
Sensor Cover Fig-6
Fig-6
1) Mark a horizontal line 1" from the top of the door for models P1 & P2,
¾for P0, and extend to the lock edge of the door as shown in .
2) Mark a vertical line 1-1/8" from the notched edge of the hinge as
shown in .
3) Mark center point at horizontal and vertical line intersects. Drill
pilot hole of 1/8" as shown in .
4) Loosen sensor cover screws enough to enable removal of the sensor cover form the mounting plate.
Loosen sensor adjustment nuts.
5) Place sensor mounting plate on the door with first mounting hole over pilot hole as shown in . Pull
out wire from wiring hole.
6) Temporarily secure the hinge side sensor mounting plate on door with two self-tapping / wood screws as
shown in .
7) Loosen adjustment nuts on mounting plate and Slide the sensor mounting plate towards the lock edge of
the door so that there is no more than 3/8"-7/16" gap between the sensor mounting plate & the lock edge as
shown in .
8) Line up the cover screws of the sensor cover with
the slots provided on the sensor mounting plate. Adjust the sensor cover as needed. Attach sensor cover
to the mounting plate and loosely tighten the cover screw provided as shown . Sensor cover
must extend over the top of the door, but make sure the top of the cover extends no more than 
above the top of the door. Test the operation of the sensor.
PULL SIDE OF THE DOOR
Telescoping Sensor
PULL SIDE OF THE DOOR
Telescoping Sensor
DOOR SENSOR
Please Read Completely Before Starting
Door Sensor
Install Instructions

INS LISA 1DR.vsd Created: 10-6-2017 Revised:10-6-2017 Page 4
9) Remove the sensor cover. Mark the locations of the lock side mounting holes, and remove entire assembly from the door.
10) Prepare each of the (4) mounting hole locations for thru-bolting: drill .201 (#7 Drill) holes at each locations.
11) Install mounting plate with (4) four 10-24 x 2" carriage bolts, #10 lock washers and hex nuts provided as shown in .
12) Optional Step: If necessary cut the mounting plate spacer to the size and fill the gap between lock side and hinge side mounting plates. Secure it
through slot with 8-32 Pan head Phillips screws and #8 Lock washers as shown in .
13) Tighten adjustment nuts on mounting plate and cover.
14) Connect the board attached header to the mounting plate spacer as shown in .
15) Secure sensor cover to the mounting plate with (2) #5 cover screws as shown in .
16) Test the operation. Press the sensor cover to check the sensitivity of the sensor. If more sensitive then detach the sensor cover and loosen the both
allen head screws as shown in . Adjust the allen head screws as needed (Tighten the screw for less sensitivity and loosen the screw for more
sensitivity). Sensor switches are NOConnect sensor to the controller.
17) LED of console should stay green. If it turns red itself, sensor should be adjusted for less sensitivity.
18) Hold the sensor and depress for 3 sec or longer. LED should turn into red. If not, sensor should be adjusted for more sensitivity.
19) Test the operation again. If good, apply blue LOCTITE® for safety to the screws and install.
Fig-7 x 2" Carriage Bolts
Lock Washers Lock Washers
Hex Nuts Hex Nuts
Fig-7
Fig-9
Fig-10
Cover Screws
#8 Lock Washers
x 2 each
x 3/16" Pan Head Phillips
Screws x 2 each Mounting Plate Spacer
Fig-8
Fig-10
Fig-8
Fig-11
Allen Head Screws
Fig-11
WARNING: Do not over-tighten. Use included allen key. Board Attached Header
Fig-9
Board Attached Header
Fig-9
Door Sensor
Install Instructions