Litecraft CYCStrobe 50 User manual

CYCStrobe 50
ILED-ST50
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USE
USER GUIDE

1A
CONTENTS
1.SafetyInstructions................................................................................................... 2
2.TechnicalSpecifications ........................................................................................... 4
3.HowToSetTheUnit ................................................................................................ 5
3.1Controlpanel ..................................................................................................... 5
3.2MainFunction ................................................................................................... 7
4.HowToControlTheUnit ....................................................................................... 11
4.1Master/SlaveBuiltInPreprogrammedFunction ............................................. 11
4.2EasyController................................................................................................. 12
4.3DMXController................................................................................................ 12
5.DMX512Configuration ......................................................................................... 13
6.DMX512Connection ............................................................................................. 15
7.Troubleshooting..................................................................................................... 16
8.FixtureCleaning..................................................................................................... 17


DeclarationofConformity

Wedeclarethatourproducts(lightingequipments)complywiththefollowingspecification
andbearsCEmarkinaccordancewiththeprovisionoftheElectromagneticCompatibility
(EMC)Directive89/336/EEC.

EN55103‐1:2009;EN55103‐2:2009;EN62471:2008;
EN61000‐3‐2:2006+A1:2009+A2:2009;EN61000‐3‐3:2008.

&
HarmonizedStandard

EN60598‐1:2008+All:2009;EN60598‐2‐17:1989+A2:1991;EN62471:2008;
EN62493:2010
Safetyofhouseholdandsimilarelectricalappliances
Part1:Generalrequirements



17A
8．FixtureCleaning
Thecleaningofopticallensesormirrorsmustbecarriedoutperiodicallytooptimizelightoutput.
Cleaningfrequencydependsontheenvironmentinwhichthefixtureoperates:damp,smokyor
particularlydirtysurroundingcancausegreateraccumulationofdirtontheunit’soptics.
yCleanwithsoftclothusingnormalglasscleaningfluid.
yAlwaysdrythepartscarefully.
yCleantheexternalopticsatleastevery20days.Cleantheinternalopticsatleastevery30/60
days.
2A
1.SafetyInstructions
WARNING
yPleasekeepthisUserGuideforfuturereference.Ifyouselltheunit,besurethatthisinstruction
bookletisincluded.
yUnpackandcheckcarefullythereisnotransportationdamagebeforeusingtheunit.
yBeforeoperating,ensurethatthevoltageandfrequencyofpowersupplymatchthepower
requirementsoftheunit.
yIt’simportanttogroundtheyellow/greenconductortoearthinordertoavoidelectricshock.
yTheunitisforindooruseonly.Useonlyinadrylocation.
yTheunitmustbeinstalledinalocationwithadequateventilation,atleast50cmfromadjacent
surfaces.Besurethatnoventilationslotsareblocked.
yDisconnectmainpowerbeforereplacementorservicing.
yMakesuretherearenoflammablematerialsclosetotheunitwhileoperatingasitisfirehazard.
yUsesafetycablewhenfixesthisunit.
yMaximumambienttemperatureisTa: 40℃.DONOToperateitwherethetemperatureishigher
thanthis.
yUnitsurfacetemperaturemayreachupto85℃.DONOTtouchthehousingbare‐handduringits
operation.Turnoffthepowerandallowabout15minutesfortheunittocooldownbefore
replacingorserving.
yIntheeventofseriousoperatingproblem,stopusingtheunitimmediately.Nevertrytorepair
theunitbyyourself.Repairscarriedoutbyunskilledpeoplecanleadtodamageormalfunction.
PleasecontactthenearestAuthorizedServiceCentre.Alwaysusetheoriginalspareparts.
yDONOTtouchanywireduringoperationashighvoltagemightbecausingelectricshock.



Pleasereadcarefullytheinstruction,whichincludesimportantinformation
abouttheinstallation,usageandmaintenance.

3A
Warning:
yTopreventorreducetheriskofelectricalshockorfire,donotexposetheunittorainor
moisture.
yDONOTopentheunitwithinfiveminutesafterswitchingoff.
yThehousing,thelenses,orfiltersmustbereplacediftheyarevisiblydamaged.
Caution:
Therearenouserserviceablepartsinsidetheunit.DONOTopenthehousingorattemptany
repair.Intheunlikelyeventtheunitrequiresservice,pleasecontactanAuthorisedService
Centre.
Installation:
Theunitshouldbemountedviaitsscrewholesonthebracket.Alwaysensurethattheunitis
firmlyfixedtoavoidvibrationandslippingwhileoperating.Andmakesurethatthestructureto
whichyouareattachingtheunitissecureandisabletosupportaweightof10timesoftheunit’s
weight.Alwaysuseasafetycablethatcanhold12timesoftheweightoftheunitwheninstalling
thefixture.
Theequipmentmustbefixedbyprofessionals.Anditmustbefixedataplacewhereisoutofthe
touchofpeopleandhasnoonepassbyorunderit,therangeofmountingheightis0~30M.
For230V50Hzpowersupply,maximumunitsthatcanbelinkedononepowercableis10
For120V60Hzpowersupply,maximumunitsthatcanbelinkedononepowercableis6
16A
7.Troubleshooting
Followingareafewcommonproblemsthatmayoccurduringoperation.Herearesome
suggestionsforeasytroubleshooting:
A.Theunitdoesnotwork,nolightandthefandoesnotwork
1. Checktheconnectionofpowerandmainfuse.
2. Measurethemainsvoltageonthemainconnector.
3. CheckthepoweronLED.
B.NotrespondingtoDMXcontroller
1. DMXLEDshouldbeon.Ifnot,checkDMXconnectors,cablestoseeiflinkproperly.
2. IftheDMXLEDisonandnoresponsetothechannel,checktheaddresssettingsandDMX
polarity.
3. IfyouhaveintermittentDMXsignalproblems,checkthepinsonconnectorsoronPCBofthe
unitorthepreviousone.
4. TrytouseanotherDMXcontroller.
5. CheckiftheDMXcablesrunnearorrunalongsidetohighvoltagecablesthatmaycause
damageorinterferencetoDMXinterfacecircuit.
C.Someunitsdon’trespondtotheeasycontroller
1. YoumayhaveabreakintheDMXcabling.ChecktheLEDfortheresponseofthemaster/
slavemodesignal.
2. WrongDMXaddressintheunit.Settheproperaddress.
D.Noresponsetothesound
1. MakesuretheunitdoesnotreceiveDMXsignal.
2. Checkmicrophonetoseeifitisgoodbytappingthemicrophone
E.Oneofthechannelsisnotworkingwell
1. ThesteppermotormightbedamagedorthecableconnectedtothePCBisbroken.
2. Themotor’sdriveIConthePCBmightbeoutofcondition

15A
6.DMX512Connection
1. Ifyouusingacontrollerwith3pinsDMXoutput,youneedtousea3to5pinadapter‐cable.
2. Atlastunit,theDMXcablehastobeterminatedwithaterminator.Soldera120ohm1/4 W 
resistorbetweenpin2(DMX‐)andpin3(DMX+)intoa3‐pinXLR‐plugandplugitinthe
DMX‐outputofthelastunit.
3. Connecttheunittogetherina`daisychain`byXLRplugfromtheoutputoftheunittothe
inputofthenextunit.Thecablecannotbranchedorsplittoa`Y`cable.DMX512isavery
high‐speedsignal.Inadequateordamagedcables,solderedjointsorcorrodedconnectorscan
easilydistortthesignalandshutdownthesystem.
4. TheDMXoutputandinputconnectorsarepass‐throughtomaintaintheDMXcircuit,when
oneoftheunits’powerisdisconnected.
5. Eachlightingunitneedstohaveanaddresssettoreceivethedatasentbythecontroller.The
addressnumberisbetween0‐511(usually0&1areequalto1).
6. TheendoftheDMX512systemshouldbeterminatedtoreducesignalerrors.
7. 3pinXLRconnectorsaremorepopularthan5pinXLR.
3pinXLR:Pin1:GND,Pin2:Negativesignal(‐),Pin3:Positivesignal(+)
5pinXLR:Pin1:GND,Pin2:Negativesignal(‐),Pin3:Positivesignal(+),Pin4/ P i n 5:Notused.
4A
2.TechnicalSpecifications
4DMXChannelModes:1/2/10/12Channels
3OperationModes: DMX512,Master/SlaveandSoundActive.
StrobeSpeed&IntensityVariableviaadjustablebyknobsandDMX.
Sound‐to‐Light  built‐inlightingshowsunderMaster/Slavemodetriggeredbymusic.
RemoteControl  OptionalCA‐8(forinstantlightingshows)
Dimming   Smooth0~100%dimming
Idealforpubs,clubs,bars,MobileDJsandmore.
◇PowerVoltage:AC100V~240V,50/60Hz
◇PowerConsumption:60W
◇LEDSources:10pcs×5WWhiteLEDs
◇Fuse:T2A
◇Weight:
2.8Kgs
◇Dimension:
602×114×141mm

5A
3.HowToSetTheUnit
3.1Controlpanel
1.FUSE（T2A）:Overcurrentprotection(replaceablefuse)
2.POWERIN:  PowerConfrommainsupplyorotherunit
3.POWEROUT:
PowerConLoopmainsupplytothenextunit.
4.DISPLAY:  Showsmenus,functions,settings.
BUTTON:
5.MENUToselecttheprogrammingfunctions
6.  DOWNTogobackwardintheselectedfunctions
7.  UPTogoforwardintheselectedfunctions
8.ENTERToconfirmtheselectedfunctions
LED:
9.DMXOnDMXinputpresent
10.MASTEROnMasterMode
11.SLAVEOnSlaveMode
12.SOUNDFlashingSoundactivation
13.SPEED:  Manuallyadjuststrobevalue.
14.DIMMER: Manuallyadjustdimmervalue.
14A
10ChannelMode:
12ChannelMode:


13A
5.DMX512Configuration
1&2ChannelModes:
6A
15.MICROPHONE:Sensorformusic/soundactivation.
16.REMOTE: OnlyforconnectionofoptionalCA‐8remotecontroller
17.DMXIN:  5pinXLRforDMX512fromcontrollerorotherunit.
18.DMXOUT:  5pinXLRforDMX512tonextunit.

























7A
3.2MainFunction
Toselectafunction,presstheMENUbuttonuntiltherequiredfunctionisshowingonthedisplay.
SelectthefunctionbypressingtheENTERbutton,thedisplaywillblink.UseDOWNandUPbutton
tochangethemode.Oncetherequiredmodehasbeenselected,presstheENTERbuttonto
confirm,ortogobacktothemainfunctionwithoutanychangepresstheMENUbutton.

MenuStructureisshownbelow
12A
4.2EasyController
TheoptionalCA‐8easyremotecontrolisusedonlyinmaster/slavemode.By
connectingtothe1/4 ” microphonejackofthefirstunit,remotecontrolofthe
firstunitispossible,andinturnwillcontrolalltheotherunitsforStandby,
FunctionandModeselection.
BlackoutBlackouttheunit
Function
SynchronousStrobebyauto
SynchronousStrobebysound
(pressandholdthebutton)
SelectShow1–12
Manualmode
ModeSound
(LEDOFF)
Show
(LEDON)
4.3DMXController
WhenusingauniversalDMXcontrollertocontroltheunits,setDMXaddressoneachunitinthe
range1to512channelsothattheunitscanreceiveDMXsignal.
PresstheMENUbuttonuptowhentheisshowingonthedisplay.PressingENTERbutton
andthedisplaywillblink.UseDOWNandUPbuttontochangetheDMX512address.Oncethe
addresshasbeenselected,pressandkeepENTERbuttonpresseduptowhenthedisplaystops
blinkingorstoringautomatically8secondslater.Togobacktothefunctionswithoutanychange
presstheMENUbuttonagain.
PleaserefertothefollowingdiagramtoaddressyourDMX512channelforthefirst4units：

11A
4.HowToControlTheUnit
Operatetheunitinoneofthreeways:
1.Master/slavebuilt‐inpreprogramfunction
2.Easycontroller
3.UniversalDMXcontroller
ThereisnoneedtoturntheunitoffwhenchangingtheDMXaddress,thenewDMXaddress
settingwilltakeeffectimmediately.Everytimetheunitisturnedon,willshowonthe
displaywhilethefixtureisinitializedthiscantakeupto20seconds.Afterthattheunitwillbe
readytoreceiveDMXsignalorrunthebuiltinprograms.
4.1Master/SlaveBuiltInPreprogrammedFunction
Bylinkingtheunitsinmaster/slaveconnection,thefirstunitwillcontroltheotherunitstogivean
automatic,soundactivated,synchronizedlightshow.Thisfunctionisgoodwhenaninstantshowis
needed.Setthefirstunitinmastermodeandselect(randomshow)or  (show1)or…
or(show12)mode.ItsDMXinputjackwillhavenothingpluggedintoit,anditsmasterLED
willbeconstantlyonandsoundLEDwillflashtothemusic.Theotherunitswillhavetosetinslave
modeandselect  (normal)or  (2‐lightshow)mode,TheirDMXcablesplugged
intotheDMXinputjacks(daisychain)andtheslaveledlightswillconstantlyon.
2‐lightshow
In  (slavemode),  meanstheunitworksnormallyand  means15‐lightshow.In
ordertocreateagreatlightshow,youcansetonthefifteenthunittogetcontrast
movementtoeachother,evenifyouhavetwounitsonly.
8A
DMX512ADDRESS
Toselectthe,presstheENTERbuttontoshowtheDMXADDRESSonthedisplay.Usethe
DOWN/UPbuttontoadjusttheaddressfrom1to512.Oncetheaddresshasbeenselected,press
theENTERbuttontosetup,togobacktothefunctionswithoutanychangespresstheMENU
buttonagain.HoldandpresstheMENUbuttonforonesecondorwaitforoneminutetoexitthe
menumode.

CHANNELMODE
Toselectthe,presstheENTERbuttontoshowtheCHANNELMODEonthedisplay.Usethe
DOWN/UPbuttontoselectthe1,2,10,12channelmodes.Oncethemodehasbeenselected,
presstheENTERbuttontosetup,togobacktothefunctionswithoutanychangespresstheMENU
buttonagain.HoldandpresstheMENUbuttonforonesecondorwaitforoneminutetoexitthe
menumode.
SLAVEMODE
Toselectthe,presstheENTERbuttontoshowtheSLAVEMODEonthedisplay.Usethe
DOWN/UPbuttontoselectthe(SLAVE1),  (SLAVE2)modes.Oncethemodehas
beenselected,presstheENTERbuttontosetup,togobacktothefunctionswithoutanychanges
presstheMENUbuttonagain.HoldandpresstheMENUbuttonforonesecondorwaitforone
minutetoexitthemenumode.
SHOWMODE
Toselectthe,presstheENTERbuttontoshowtheSHOWMODEonthedisplay.Usethe
DOWN/UPbuttontoselectthe(Randomshow),  (Show1)or…or(Show
12)modeand(Manualshow).Oncethemodehasbeenselected,presstheENTERbutton
tosetup,togobacktothefunctionswithoutanychangespresstheMENUbuttonagain.Holdand
presstheMENUbuttonforonesecondorwaitforoneminutetoexitthemenumode.

9A
MANUALMODE
Toselectthe,presstheENTERbuttontoshowtheMANUALMODEonthedisplay.Usethe
DOWN/UPbuttontoselectthe(Dimmer)or  (Strobe).Oncethemodehasbeen
selected,presstheENTERbutton,andusetheDOWNandUPbuttontoadjustthevalue(0‐255).
Onceselected,presstheENTERbuttontosetup,togobacktothefunctionswithoutanychanges
presstheMENUbuttonagain.HoldandpresstheMENUbuttonforonesecondorwaitforone
minutetoexitthemenumode.

SOUNDMODE
Toselectthe,presstheENTERbuttontoshowtheSOUNDMODEonthedisplay.Usethe
DOWN/UPbuttontoselectthe(soundon)or  (soundoff)mode.Oncethemode
hasbeenselected,presstheENTERbuttontosetup,togobacktothefunctionswithoutany
changespresstheMENUbuttonagain.HoldandpresstheMENUbuttonforonesecondorwait
foroneminutetoexitthemenumode.

BLACKOUTMODE
Toselectthe,presstheENTERbuttontoshowtheBALCKOUTMODEonthedisplay.Use
theDOWN/UPbuttontoselectthe(blackout)or  (normal)mode.Oncethe
modehasbeenselected,presstheENTERbuttontosetup,togobacktothefunctionswithoutany
changespresstheMENUbuttonagain.HoldandpresstheMENUbuttonforonesecondorwait
foroneminutetoexitthemenumode.

LEDDISPLAY
Toselectthe,presstheENTERbuttontoshowtheLEDDISPLAYonthedisplay.Usethe
DOWN/UPbuttontoselectthe(LEDon)or(LEDoff)mode.Oncethemodehas
beenselected,presstheENTERbuttontosetup,togobacktothefunctionswithoutanychanges
presstheMENUbuttonagain.HoldandpresstheMENUbuttonforonesecondorwaitforone
minutetoexitthemenumode.
10A
DISPLAYINVERSE
Toselectthe,presstheENTERbuttontoshowtheDISPLAYonthedisplay.Usethe
DOWN/UPbuttontoselectthe(normal)or  (inversion),pressENTERbuttonto
setup.BacktothefunctionswithoutanychangepressMENUbutton.

AUTOTEST
Toselectthe,presstheENTERbuttontoshowtheTESTonthedisplayandtheunitwillrun
aself‐test.TogobacktothefunctionswithoutanychangespresstheMENUbuttonagain.Hold
andpresstheMENUbuttonforonesecondorwaitforoneminutetoexitthemenumode.

TEMP.
Toselectthe,presstheENTERbuttontoshowtheTEMP.onthedisplayandthedisplay
willshowthetemperatureoftheunit.Togobacktothefunctionswithoutanychangespressthe
MENUbuttonagain.HoldandpresstheMENUbuttonforonesecondorwaitforoneminuteto
exitthemenumode.
FIXTUREHOURS
Toselectthe,presstheENTERbuttontoshowtheFIXTUREHOURSonthedisplayandthe
displaywillshowthenumberofworkinghoursoftheunit.Togobacktothefunctionswithout
anychangespresstheMENUbuttonagain.HoldandpresstheMENUbuttonforonesecondor
waitforoneminutetoexitthemenumode.

SOFTWAREVERSION
Toselectthe,presstheENTERbuttontoshowtheSOFTWAREVERSIONonthedisplayand
thedisplaywillshowtheversionofsoftwareoftheunit.Togobacktothefunctionswithoutany
changespresstheMENUbuttonagain.HoldandpresstheMENUbuttonforonesecondorwait
foroneminutetoexitthemenumode.