Litecraft PAR 64 AT10 User manual

PAR 64 AT10
MANUAL
Thank you for purchasing this LITECRAFT product. For your own safety, please
read the instruction manual carefully before turn on the product for the first time.
SAFETY NOTES
•Each person which is responsible for the installation, the use or service
of this unit must be:
- qualified
- has to follow the instructions in this manual.
•WARNING! Be careful when using the device. You risk an electrical
shock from high voltage, if you touch the wires!
•The device has left our company in manufacturer proofed state. To
maintain this status and to ensure a permanent safe operation, it is
absolutely necessary to follow the safety instructions and warnings in
this manual.
•IMPORTANT: Errors, caused by not following these instructions are not
covered by the warranty. The manufacturer will not accept liability for any
resulting defects or problems.
•Keep the unit away from radiators or other heat sources!
•If the unit has been exposed to tremendous temperature changes (e.g.
after transportation), do not turn it on immediately. The resulting
condensation could damage the unit. Don`t switch unit on until the
device reaches room temperature.
•This device belongs to protection class I. Therefore, it is imperative that
the green/yellow wire is connected to the earth contact of the plug. The
electrical connection must be made by a qualified person.
I

•Make sure that the cable has never been squeezed or damaged by
sharp objects. Check the device and the cables regularly.
•If the cable is damaged, it must be replaced immediately by the
manufacturer, its service agent or a qualified person in order to avoid
danger.
•Lenses, glasses or UV filters must be replaced if they are visually
damaged, or their effectiveness is impaired, e.g. by broken glass or by
deep scratches.
•Ensure that wires never come in contact with other wires! Handle the
power cord and all connections with caution!
•Make sure that the line voltage is not higher than the voltage specified in
this manual.
•Disconnect the unit from the AC mains when it is not in use or when
cleaning it. Disconnect the connection only by pulling the cable plug.
•Using the fixture for the first time, can result in light smoke and odors.
This is a normal process and does not constitute a defect.
•RISK OF BURNS! Do not touch the unit during operation! The housing
may reach high temperatures.
•RISK TO HEALTH! Never look directly into the light source. Especially
epileptics risk an epileptic shock! Disconnect the unit from the AC mains
when not in use or when cleaning it.
•Defects caused by modifications of the device by unqualified handling or
an unqualified person are not covered by the warranty.
•Keep the product away from children and unskilled people.
•There are no wear parts in the device. Maintenance and service must be
performed only by an authorized service partner.
II

OPERATION
•This device has several DMX- and Stand-Alone-Modes. In DMX-mode,
multiple devices can be connected and controlled by a controller. The
device accepts the settings of the DMX-controller, as soon as the
corresponding start address is set.
•Slave mode:
Connect the DMX-output of the master device (XLR female) to the
DMX-input of the slave device (XLR male). Set the slave device to
DMX-mode DMX-4CH with the DMX-start address 001 (display shows:
DMX-4CH/DMX 001). The slave device accepts all settings of the
master device (such as color macro, programm, programm speed, color
set).
•Display description:
The display shows the different DMX-modes & the DMX-start address or
color macro, programm, programm speed, color set; the first line shows
the mode, the second line the corresponding value. If a DMX-mode is
choosen, but actually there is no DMX-signal present, the display flashes
and shows NO SIGNAL.
•Button description:
Press the MODE button repeatedly to select the mode. Press the UP or
DOWN button to set the DMX-start address or any of the
pre-programmed modes or the speed values. Use the UP button to
increase the value. Use the DOWN button to decrease it.
NOTE!
If you hold the UP or DOWN button for longer than 3 seconds, the value
changes faster. The device has an automatic storage for all settings.
When you turn the device off and on again, it works with the previously
set values.
III

CONTROL MODES / DMX DESCRIBTION
mode display function
LITECRAFT
SW.V 1.0 shows the software version direct after switching on the unit
DEF. SET
YES alle settings will be set to factory defaults (DMX-4CH, address 001)
DEF. SET
NO all settings (DMX mode/macro etc. ) will not be changed – this menue disappears
automaticly after 5 seconds
DispPerm
ON display permanent on
display
mode
DispPerm
OFF display switches off after 10 s and switches on by pressing any button for at least 3 s
1 channel mode DMX-1CH
DMX ***
*** = DMX adress
ch1 = color macro mode
(43 colors + black)
2 channel mode DMX-2CH
DMX ***
*** = DMX adress
ch1 = color macro mode
(43 colors + black)
ch2 = dimmer
3 channel mode DMX-3CH
DMX ***
*** = DMX adress
ch1 = dimmer red
ch2 = dimmer green
ch3 = dimmer blue
4 channel mode DMX-4CH
DMX ***
*** = DMX adress
ch1 = dimmer red
ch2 = dimmer green
ch3 = dimmer blue
ch4 = dimmer amber
DMX-
mode
8 channel mode DMX-8CH
DMX ***
*** = DMX adress
ch1 = dimmer red
ch2 = dimmer green
ch3 = dimmer blue
ch4 = dimmer amber
ch5 = color macro mode
0-13 no macro
14-255 pre-programmed colors
ch6 = strobe/speed
0-15 no strobe
16-255 strobe 16 speed values
ch7 = mode
0-35 no function
36-71 automtic ramp up */**
72-107 automatic ramp down */**
108-143 automatic ramp up/down */**
144-179 automatic color mix mode
180-215 random 3-colors *
216-251 random 7-colors *
252-255 audio mode
ch8 = dimmer
* speed value by channel 6
** color value by channel 1, 2, 3, 4
color macro
mode ColMacro Macro**
** = pre-programmed
colors
choose one of 43 pre-programmed colors +
black
programm mode ColProgr
Prog**
** = pre-programmed
chasers
choose one of 6 pre-programmed chasers
programm speed ColSpeed
Speed**
** = speed value
choose one of 16 speed values for the
programm choosed in programm mode
manual
mode
color set red
ColSet Red ***
*** = color value red
256 DMX-steps to set color red
IV

color set green
ColSet Green ***
*** = color value green
256 DMX-steps to set color green
color set blue
ColSet Blue ***
*** = color value blue
256 DMX-steps to set color blue
color set amber
ColSet Amb ***
*** = value white
256 DMX-steps to set color amber
special
functions fixture hour counter FixHours ***** h ***** = fixture working hours
V

MACRO VALUE OVERVIEW
value red value green value blue value amber
black 0 0 0 0
macro 1 0 0 128
0
macro 2 0 0 192
0
macro 3 0 0 255
0
macro 4 0 128 0 0
macro 5 0 128 128 0
macro 6 0 128 192 0
macro 7 0 128 255 0
macro 8 0 255 0 0
macro 9 0 255 128 0
macro 10 0 255 192 0
macro 11 0 255 255 0
macro 12 128 0 0 0
macro 13 128 0 128 0
macro 14 128 0 192 0
macro 15 128 0 255 0
macro 16 128 128 0 0
macro 17 128 128 128 0
macro 18 128 128 192 0
macro 19 128 128 255 0
macro 20 128 255 0 0
macro 21 128 255 128 0
macro 22 128 255 192 0
macro 23 128 255 255 0
macro 24 255 0 0 0
macro 25 255 0 128 0
macro 26 255 0 192 0
macro 27 255 0 255 0
macro 28 255 128 0 0
macro 29 255 128 128 0
macro 30 255 128 192 0
macro 31 255 128 255 0
macro 32 255 255 0 0
macro 33 255 255 128 0
macro 34 255 255 192 0
macro 35 255 255 255 0
macro 36 255 0 0 255
macro 37 0 255 0 255
macro 38 0 0 255 255
macro 39 0 0 0 255
macro 40 255 255 0 255
macro 41 255 0 255 255
macro 42 0 255 255 255
macro 43 255 255 255 255
VI

VII
TECHNICAL SPECIFICATION
voltage 90-264 V, 47-63 Hz
power consumption 0.6 A @ 230 V
measurements 267 x 249 x 321 mm
weight 5.2 kg
fuse T3.15 A @ 250 V