Programming the Controller
1. Connect the LOAD wire first following polarity marked at
the back of the controller, followed by the LINE wire. Make
sure that a short circuit cannot occur between the connected
wires before you turn on the power. Do not exceed maximum
loading.
2. There are six keys allocated on the remote control; the function
of each key is as follows:
MODE: mode button, a total of 10 different modes.
ON/OFF: power switch button.
B +: to increase the overall brightness, a total of 10 steps.
B -: to decrease the overall brightness, a total of 10 steps.
S +: to increase the color alternating rate, a total of 10 steps
(ranging from five seconds to one hour).
S -: to decrease the color alternating rate, a total of 10 steps.
3. There are 10 keys allocated on the controller; the function of
each key is as follows:
STEP ↑: to cycle to the previous step.
STEP ↓: to cycle to the next step.
PARA ↑: to cycle upwards through the list of parameters.
PARA ↓: to cycle downwards through the list of parameters.
VALUE +: to increase the value of the corresponding parameter
(hold down the button for a fast numerical increase).
VALUE -: to decrease the value of the corresponding parameter
(hold down the button for a fast numerical decrease).
DELETE: to remove the current step.
INSERT: to insert steps (after the current step).
ADD: to add an additional step (after the last step) for a total of
20 steps.
PLAY/PAUSE: to play or pause the step sequence (when
programming, player must be suspended/paused).
4. The programmable controller’s standard built-in modes are
shown in the table below:
No Function Remarks Key function
location
1 Static yellow Brightness adjustable (25-255) Remote
2 Static purple Brightness adjustable (25-255) Remote
3 Static cyan Brightness adjustable (25-255) Remote
4 Static blue Brightness adjustable (25-255) Remote
5 Static green Brightness adjustable (25-255) Remote
6 Static red Brightness adjustable (25-255) Remote
7 Static white Brightness adjustable (25-255) Remote
8 DIY program User defined parameters Controller
9 Seven-color
fade changing Brightness adjustable (25-255)
Speed adjustable (0-9) Remote
10 Seven-color
step changing Brightness adjustable (25-255)
Speed adjustable (0-9) Remote
5. In DIY program mode (#8), each STEP can be set with an
independent value with a total of five parameter (including time
to hold at current step, transitional time to following step, red
light value, green light value and blue light value).
To program the controller, proceed with the following steps:
a. Make sure that the screen displays “STEP **/**” (if it
doesn’t, press the PLAY/PAUSE button once).
b. Press the STEP ↑or STEP ↓to cycle through the steps (1-10)
and choose which step to start at first.
c. Press the PARA ↑or PARA ↓to cycle through the parameters
of the corresponding step as follows:
i. Blue, Green and Red color can be independently
adjusted from 0 to 255 to create your own color, see
5(d).
ii. Length of the step (“hold”), can be incrementally adjusted
from 1/8 sec to 2h, see 5(d).
iii. Transitional period (“change”) between consecutive
steps, can be incrementally adjusted from 1/8 sec to 2h,
see 5(d).
d. Press the VALUE + to increase or VALUE - to decrease the
value of the corresponding parameter.
6. To add an additional step at the current position (if the total
steps is less than 20), press the INSERT button and repeat steps
5(c) and 5(d) to configure the parameters.
7. To add an additional step after the last step (if the total steps is
less than 20), press the ADD button and repeat steps 5(c) and
5(d) to configure the parameters.
8. To delete a particular step, cycle through the steps by pressing
the STEP ↑or STEP ↓buttons. Stop at the desired step and press
the DELETE button once.
9. Press PLAY/PAUSE button again to exit programming mode.
REV057-8.6.10
DazzLEDTM is a registered trademark of /
DazzLEDMC est une marque déposé de :
Liteline Corporation
Imported exclusively by / Importateur en exclusivité :
Liteline Corporation, Brampton, Ontario, Canada L6T 5B7
Website / Site web : liteline.com
Toll free technical support / Soutien technique
téléphonique sans frais : 1-866-730-7704
