SMC Networks JXCP1 User manual

PRODUCT NAME
PROFINET Direct input type
Step Motor Controller
(Servo 24VDC)
Model / Series / Product Number
JXCP1
No.JXC※-OMT0006-C

- 1 -
Table of Contents
1. Safety Instructions ..............................................4
2. Outlines of Product .............................................6
2.1 Features..............................................................................................6
2.2 How to Order......................................................................................7
2.3 Product configuration......................................................................8
2.4 Start up procedure............................................................................9
(1) Checking the contents of the package............................9
(2) Mounting the controller.....................................................9
(3) Wiring and Connection......................................................9
(4) Supply of power .................................................................9
(5) Configuration....................................................................10
(6) Setup of the operation parameters ................................10
(7) Test run..............................................................................10
3. Specifications ....................................................11
3.1 Specifications..................................................................................11
3.2 Parts Description............................................................................12
3.3 External Dimensions......................................................................13
(1) Screw mounting (JXCP17-□)...........................................13
(2) DIN rail mounting (JXCP18-□).........................................14
3.4 Mounting...........................................................................................15
(1) Mounting...........................................................................15
(2) Grounding.........................................................................15
(3) Mounting location............................................................16
4. Initial Setting method ........................................17
4.1 GSDML file and icons.....................................................................17
4.2 GSDML file installation...................................................................17
4.3 Addition of JXCP1 controller to PROFINET network...............18
4.4 Registration of the device name of the JXCP1 controller to be connected 19
5. External Connections........................................21
5.1 PWR: Power supply connector.................................................21
5.2 MOT: Motor connector, ENC: Encoder connector............21
5.3 SI: Serial I/O Connector...............................................................21
(1) Connecting the teaching box..........................................21
(2) Connection with a PC......................................................22
5.4 P1, P2: PROFINET communication connector.......................22
6. Details of Power Supply Plug ...........................23
6.1 PWR: Power supply plug specifications....................................23
6.2 Electrical Wiring Specifications...................................................23
6.3 Power Supply Plug Wiring............................................................24
(1) Wiring of power supply (C24V, M24V, 0V) .....................24
(2) Wiring of the stop switch (EMG).....................................24
(3) Wiring of the lock release (LK RLS)...............................24
6.4 Wiring of stop circuit......................................................................25

- 2 -
(1)Stop (example of recommended circuit)........................25
(2) Stop (relay contact (1)) ....................................................26
(3) Motor power shutdown (relay contact (2)) ....................27
7. LED display........................................................28
7.1 LED display......................................................................................28
7.2 LED and Controller Status.............................................................28
8. Operation methods............................................29
8.1 Outline...............................................................................................29
8.2 Operation by Step No.....................................................................29
8.3 Position/speed monitor.................................................................29
8.4 Operation by numerical instruction ............................................29
9. Memory map ......................................................30
9.1 Memory allocation ..........................................................................30
(1) Input Area Mapping..........................................................30
(2) Input area details..............................................................31
(3) Output area mapping.......................................................35
(4) Output area details...........................................................36
(5) Record data (request sent from PROFINET master to JXCP1 controller) 40
10. Settings and Data Entry ..................................41
10.1 Step Data........................................................................................41
10.2 Basic parameters..........................................................................44
10.3 Return to origin parameter..........................................................46
11. Operations........................................................47
11.1 Return to Origin.............................................................................47
11.2 Positioning Operation..................................................................47
11.3 Pushing Operation........................................................................48
(1) Pushing operation is successfully performed..............48
(2) Pushing operation fails (empty pushing)......................48
(3) Movement of the workpiece after the completion of the pushing process48
11.4 Controller signal response time.................................................49
11.5 Methods of interrupting operation.............................................49
12. Operation Examples........................................50
12.1 Positioning Operation..................................................................50
12.2 Pushing Operation .......................................................................51
13. Operation Instructions ....................................52
13.1 Overview of the Operation Instructions...................................52
13.2 Operation procedure for Operation by Step No......................52
[1] Power on and Return to Origin position........................52
[2] Positioning operation......................................................53
[3] Pushing Operation...........................................................54
[4] HOLD .................................................................................54
[5] Reset..................................................................................55
[6] Stop....................................................................................55
[7] Area output .......................................................................56
13.3 Operation procedure for Operation by numerical instruction57

- 3 -
14. Options.............................................................58
14.1 Actuator cable [5m or shorter]...................................................58
14.2 Actuator cable [8 to 20m]............................................................58
14.3 Actuator cable for with lock [5m or less] .................................59
14.4 Actuator cable for with lock [8 to 20m].....................................59
14.5 Controller Set up kit.....................................................................60
14.6 Power supply plug........................................................................60
14.7 Teaching box.................................................................................61
15. Alarm for Motor Control ..................................62
15.1 Alarm group signals.....................................................................62
15.2 Reading PROFINET Diagnostics from the JXCP1..................63
15.3 Alarms and countermeasures....................................................64
16. Precautions for wiring and cable....................69
17. Electric Actuators/Common Precautions.......70
17.1 Design and selection....................................................................70
17.2 Mounting ........................................................................................71
17.3. Handling Precautions.................................................................72
17.4 Operating environment................................................................73
17.5 Maintenance Precautions............................................................74
17.6 Precautions for actuator with lock............................................74
18. ControllerandPeripheralDevices/SpecificProductPrecautions 75
18.1 Design and selection....................................................................75
18.2 Handling Precautions ..................................................................76
18.3 Mounting ........................................................................................77
18.4 Wiring..............................................................................................77
18.5 Power supply.................................................................................78
18.6 Grounding......................................................................................78
18.7 Maintenance...................................................................................78
19. Troubleshooting ..............................................79
20. Handling of sent/received data.......................84
21. Definitions and terminology ...........................85

- 4 -
JXCP1/Controller
1. Safety Instructions
These safety instructions are intended to prevent hazardous situations and/or equipment damage.
These instructions indicate the level of potential hazard with the labels of "Caution", "Warning" or
"Danger". They are all important notes for safety and must be followed in addition to International
Standards (ISO/IEC) 1) and other safety regulations.
1) ISO 4414: Pneumatic fluid power －－ General rules relating to systems
ISO 4413: Hydraulic fluid power －－ General rules relating to systems
IEC 60204-1: Safety of machinery －－ Electrical equipment of machines (Part 1: General requirements)
IEC 10218: Manipulating industrial robots －－ Safety
Caution
CAUTION indicates a hazard with a low level of risk which, if not avoided, could
result in minor or moderate injury.
Warning
WARNING indicates a hazard with a medium level of risk which, if not avoided, could
result in death or serious injury.
Danger
Danger indicates a hazard with a high level of risk which, if not avoided, could result
in death or serious injury.
Warning
(1) The compatibility of the product is the responsibility of the person who designs the equipment or
decides its specifications.
Since the product specified here is used under various operating conditions, its compatibility with
specific equipment must be decided by the person who designs the equipment or decides its
specifications based on necessary analysis and test results.
The expected performance and safety assurance of the equipment will be the responsibility of the
person who has determined its compatibility with the product.
This person should also continuously review all specifications of the product referring to its latest
catalog information, with a view to giving due consideration to any possibility of equipment failure
when configuring the equipment.
(2) Only personnel with appropriate training should operate machinery and equipment.
The product specified here may become unsafe if handled incorrectly.
The assembly, operation and maintenance of machines or equipment including our products must
be performed by an operator who is appropriately trained and experienced.
(3) Do not service or attempt to remove product and machinery/equipment until safety is confirmed.
1. The inspection and maintenance of machinery/equipment should only be performed after
measures to prevent falling or runaway of the driven objects have been confirmed.
2. When the product is to be removed, confirm that the safety measures as mentioned above are
implemented and the power from any appropriate source is cut, and read and understand the
specific product precautions of all relevant products carefully.
3. Before machinery/equipment is restarted, take measures to prevent unexpected operation and
malfunction.
(4) Contact SMC beforehand and take special consideration of safety measures if the product is to be
used in any of the following conditions.
1. Conditions and environments outside of the given specifications, or use outdoors or in a place
exposed to direct sunlight.
2. Installation on equipment in conjunction with atomic energy, railways, air navigation, space,
shipping, vehicles, military, medical treatment, combustion and recreation, or equipment in
contact with food and beverages, emergency stop circuits, clutch and brake circuits in press
applications, safety equipment or other applications unsuitable for the standard specifications
described in the product catalog.
3. An application which could have negative effects on people, property, or animals requiring
special safety analysis.
4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by
using a mechanical protective function, and periodical checks to confirm proper operation.
Please perform periodic inspection to confirm proper operation.

- 5 -
JXCP1/Controller
1. Safety Instructions
Caution
The product is provided for use in manufacturing industries.
The product herein described is basically provided for peaceful use in manufacturing industries.
If considering using the product in other industries, consult SMC beforehand and provide
specifications or a contract, if necessary.
If anything is unclear, contact your nearest sales branch.
Limited Warranty and Disclaimer/
Compliance Requirements
The product used is subject to the following "Limited Warranty and Disclaimer" and "Compliance
Requirements".
Read and accept them before using the product.
Limited Warranty and Disclaimer
(1) The warranty period of the product is 1 year in service or 1.5 years after the product is delivered,
whichever is first. 3)
Also, the product may have specified durability, running distance or replacement parts.
Please consult your nearest sales branch.
(2) For any failure or damage reported within the warranty period, which is clearly our responsibility, a
replacement product or necessary parts will be provided.
This limited warranty applies only to our product independently, and not to any other damage
incurred due to the failure of the product.
(3) Prior to using SMC products, please read and understand the warranty terms and disclaimers
noted in the specified catalog for the particular products.
3) Vacuum pads are excluded from this 1 year warranty.
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
Also, even within the warranty period, the wear of a product due to the use of the vacuum pad or failure due
to the deterioration of rubber material are not covered by the limited warranty.
Compliance Requirements
1. The use of SMC products with production equipment for the manufacture of weapons of mass
destruction (WMD) or any other weapon is strictly prohibited.
2. The exports of SMC products or technology from one country to another are governed by the
relevant security laws and regulation of the countries involved in the transaction. Prior to the
shipment of a SMC product to another country, assure that all local rules governing that export are
known and followed.

- 6 -
2. Outlines of Product
2.1 Features
Features of the controller.
●PROFINET compatible
This device can be directly connected to a PROFINET fieldbus network. It will then be possible to
establish communication with a PROFINET Master (PLC).
●Actuator control
Positioning operation and operation at a specific speed and force for the actuator are possible by
controlling the Step motor (servo 24VDC).
●Specified force operation
Control the pushing force or the pressing force of the actuator.
●Separated power supply
Power supply input is separated into the motor power supply and control power supply. Even if the
power supply for the motor is turned OFF, the information from the encoder position is retained whilst
the control power supply is ON, and PROFINETcommunication and serial communication is available.
●Return to origin
Returning to origin is possible by a signal from PROFINET.
●Alarm detection function
Abnormal conditions are automatically detected. Alarms are output via EtherNet/IP communication.
The alarm history can be stored in the controller memory.
●Positioning / pushing operation is available with step data and numerical operation mode
It is possible to operate the actuator by using the saved step data and by numeric data operation
instruction by using PROFINET communication.
In the step data operation mode, the operation is instructed by manipulating the memory which is
relevant to input/output port such as DRIVE signal and INP signal. The actuator operates in
accordance with the step data operating pattern of the specified step data.
In the numerical operation mode, the operation is executed by specifying the releveant numeric data.
●”AREA” signal
The controller has an “AREA” signal that turns ON if the actuator position is within the range
specified by "Area 1" and "Area 2" in the step data.
●Data input method
It is possible to perform status monitoring, reset alarms and set Step data via PROFINET
communication,ACT controller software or teaching box. In addition theACT controller software or
teaching box can be used for parameter setup and trial run.
●Easy mode and Normal mode
There are two available modes for the controller setting software and the teaching box. In Easy mode,
you can start the operation by only setting the speed, position, etc. In Normal mode, further detailed
setup can be performed.
Caution
When the device is set up or failure occurs, please refer the operation manual of the actuator and
the teaching box as well as this operation manual.
Keep this operation manual accessible for reference when necessary.

- 7 -
2.2 How to Order
How to order is shown below.
Caution
Single controllers are also shipped after setting the actuator
specification parameters.
Confirm the combination of the controller and the actuator is
correct.
<Check the following before use.>
•Check the actuator label for the actuator model number.
Check that the actuator model matches the label on the
controller.
Caution
Refer to the chart of LECPMJ for checking the chart of <Speed - Work load> of actuator.
A high peak current is required to be supplied by the controller when the actuator motor is turned ON.
Please use a power supply with a current capacity of at least 1.5 times the peak power that is required
by the actuator motor
JX C P 1 -
Electric equipment
Controller type
P
PROFINET
Number of shaft/
Type of power supply
1
1 axis, Power supply
(24VDC)
Mounting
7
Direct mounting
8
DIN rail
Actuator Model
(Enter from the actuator model to "stroke")
E.g.) LEFS16B-100B-S1CP17,
input “LEFS16B-100”.
Controller
LEHZ10K2-4

- 8 -
位置 速度
100 500
200 1000
50 200
1
2
3
ﾃｽﾄ
ﾃｽﾄ
ﾃｽﾄ
現在位 置 120.3
現在速 度 200
mm
mm/ s
動作中
アラー ム
モニタ
設定 位置 速度
100 500
200 1000
50 200
1
2
3
ﾃｽﾄ
ﾃｽﾄ
ﾃｽﾄ
現在位 置 120.3
現在速 度 200
mm
mm/ s
動作中
アラー ム
モニタ
設定
•Power supply plug (Included)
Part No.: JXC-CPW
<Applicable wire size>
AWG20 (0.5mm2)
PLC
Controller power
supply
24VDC
•Controller set up kit
(Controller setting software,
communication cable,
conversion unit, USB cable
are included)
Part No: JXC-W2
•Communication cable
PC
•Conversion
unit
•USB cable
(A-miniB type)
•Conversion cable
Product no.: P5062-5
2.3 Product configuration
An example of the controller structure is shown below.
1. These items are included when ordered using the part number for an actuator set.
2. Latest version of the controller setting software must be used.
Software can be downloaded from SMC website. http://www.smcworld.com/
Warning
Refer to 5. External Connections (P.21)for wiring.
Refer to 16. Precautions for wiring and cable (P.69)when handling the wiring and cables.
The Communication cable must be connected to a PC using a USB cable through a conversion unit.
Do not connect the teaching box to a PC, as this may cause damage to the personal computer.
1
Electric actuator
To MOT
To ENC
•Actuator cable
(Robotic type cable)
Model number:
•LE-CP-□-□
(Robotic type cable)
•LE-CP-□-□-S
(Standard cable)
1
PROFINET
•Teaching box
(3m cable is provided.)
Part No: LEC-T1-3□G□
(Option)
To SI
or
2
To PWR
●Controller
To P1, P2

- 9 -
2.4 Start up procedure
Install, wire, set and operate the controller referring to the procedure below when the product is used
for the first time.
(1) Checking the contents of the package
After unpacking everything, check the description on the label to identify the controller and the
number of accessories. If any parts are missing or damaged, please contact your distributor.
Product name
Quantity
Controller
Power supply plug
（JXC-CPW）
Controller
(JXCP1□-□)
1 pc.
Power supply plug
（JXC-CPW）
1 pc.
Actuator1
1 pc.
1. These items are included when ordered
using the part number for an actuator set.
[Options]
•Teaching box (Part No: LEC-T1-3 G )
•Controller set up kit (Part No: JXC-W2)
(Controller setting software, communication cable,
USB cable and conversion unit are included)
•Conversion cable (Part No: P5062-5)
(2) Mounting the controller
Refer to section 3.4 Mounting (P.15)for instructions on how to mount the controller.
(3) Wiring and Connection
Connect the cables to the controller.
Refer to 5. External Connections (P.21)for the wiring of the connectors.
(4) Supply of power
Supply power 24VDC.
If the condition is normal, LED on the front of the controller turns ON as shown on the table below
Items
LED condition
Status
PWR
Green LED is ON
Supply power
ALM
OFF
No alarm
Refer to 7. LED display (P.28)for the explanation of LED lamps.
If the red [ALM] LED on the front of the controller (JXC) is ON, an alarm has been triggered.
Caution
When an alarm is generated
Refer to a corresponding memory of PROFINET or connect a PC or teaching box to the SI serial I/O
connector and check the details of the alarm. Then, remove the cause of the error referring to the
15. Alarm for Motor Control (P.62).
Please refer to the manuals of the controller setting software or the teaching box for details of the
alarms.
Controller set up kit
Cables & conversion unit
including
Teaching box
(Conversion cable is needed)
Option

- 10 -
(5) Configuration
Using the PLC setting software, the following steps are required to use the JXCP1 on a PROFINET
network.
- Install the GSDML file and icon.
- Using the hardware configurator, create a PROFINET network then add the device
(JXCP1 controller).
- Using hardware configurator, assign a device name and IP address to the device
(JXCP1 controller).
- Write a device name directly into the physical device (JXCP1), this should match the name used in
the hardware configuration.
When the setting of the PLC and JXCP1 controller is completed and the PROFINET communication
is established, the LED’s on the front of the controller will be set as shown in the table below.
Items
LED condition
Status
PWR
Green LED is ON
Supply power
ALM
OFF
No alarm
SF
OFF
Controller is operating correctly.
BF
OFF
PROFINET connection is established.
Refer to 7 LED display (P.28)for the explanation of the LED’s.
Communication between PLC and controller is not established when the BF red LED is on or is
flashing red.
Caution
Communication between PLC and controller is not established.
Refer to 19. Troubleshooting (P.79)
Check if the communication speed of the PLC and controller and the information of the host computer
are correctly set.
(6) Setup of the operation parameters
Set up the operation pattern (step data, basic parameters and return to origin parameters) to specify
the target position, speed, etc. by using a PC (with the controller setting software) or the teaching
box.
■PC (Normal mode)
■Teaching box
Please refer to the manuals of the controller setting software or the teaching box for how to set up the
operation pattern.
(7) Test run
Refer to 9. Memory map (P.30) for the assignment of the memory.
Input signals from PLC for checking the operation. Refer to 13. Operation Instructions (P.52) for
the operation.

- 11 -
3. Specifications
3.1 Specifications
Basic specifications of the product.
Item
Specifications
Compatible motor
Step motor (servo 24 VDC)
Power supply
Power supply voltage: 24 VDC±10%
Current consumption
200 mA or less (Controller)
Refer to the specification of actuator to be connected for total power
consumption.
Compatible encoder
IncrementalA/B phase (800 pulse/rotation)
Memory
EEPROM
LED display
LED
Details
PWR
Power supply
ALM
Alarm status
SF
Controller status
BF
PROFINET communication status.
Locking
With unlocking terminal
Cable length
Actuator cable: 20 m or less
Cooling method
Air-cooling type
Operating temperature range:
0 oC to 40 oC (No freezing)
Operating humidity range
90% RH or less (No condensation)
Insulation resistance
Between the external terminals and case
50 MΩ (500 VDC)
Weight
220 g (Direct mounting type)
240 g (DIN rail mounting type)
[PROFINET communication]
Items
Specification
Protocol
PROFINET (Version 2.32)
IP address setting range
0.0.0.0 to 255.255.255.255 (set using DCP service)
Communication speed
100 Mbps
Communication method
Full duplex/ Half duplex (automatic negotiation)
Communication cable
Standard Ethernet cable (STP, CAT5 or higher, 100BASE-TX)
Setup file
GSDML file (download from SMC website).
Occupied area
Input 36 byte / Output 36 byte
Vendor ID
83h（SMC Corporation）
Device ID
0Fh
Applicable function
I/O data
Record data
MRP
Device_Access
Conformance Class C (RT/IRT)

- 12 -
3.2 Parts Description
Details of the parts of the controller.
No.
Display
Name
Details
1
-
Display
LED’s to indicate the controller status.
2
P1, P2
PROFINET
communication
connectors
Connect to the PROFINET network.
3
SI
Serial I/O connector
(8 poles)
Connector for the teaching box (LEC-T1) or the
setting software (JXC-W2).
4
ENC
Encoder connector
(16 poles)
Connect to the actuator cable.
5
MOT
Motor driving connector
(6 poles)
6
PWR
Power supply connector
(5 poles)
Connect to the controller power supply (24VDC)
using the power supply plug.
Control power (+), Stop signal (+), Motor power (+),
Lock release (+), Common power (-)
7
-
Applicable actuator part
number label
Label indicating the actuator part number which can
be connected to the controller.
8
-
Controller part number
label
Label indicating the controller part number.
9
-
MAC address
Label indicating the PROFINET MAC address.
10
-
FE
Functional Ground
When the controller is mounted, tighten screws and
connect the grounding cable.
9
2
4
5
6
7
8
3
10
1

- 13 -
3.3 External Dimensions
The appearance of this product is as shown in the diagram below:
(1) Screw mounting (JXCP17-□)

- 14 -
(2) DIN rail mounting (JXCP18-□)

- 15 -
3.4 Mounting
(1) Mounting
The controller can be direct mounted using screws or mounted on a DIN rail.
Details of the controller mounting options are shown below.
[1]Thread mounting (JXCP17-□)
[2]DIN rail mounting (JXCP18-□)
(Mounting with two M4 screws)
(Mounting with DIN rail)
Before locked onto DIN rail
Locked onto DIN rail
(2) Grounding
Place the grounding cable with crimped terminal between the M4 screw and shakeproof washer as
shown below and tighten the screw.
Caution
The M4 screw, cable with crimped terminal and shakeproof washer must be prepared by the user.
The controller must be connected to Ground to reduce noise.
Controller
M4 screw
Cable with crimping terminal
Shakeproof washer

- 16 -
Caution
(1)A dedicated Ground connection must be used. Grounding should be to a D-class ground
(ground resistance of 100Ω or less).
(2) The cross sectional area of the grounding cable shall be 2mm2minimum.
The Grounding point should be as near as possible to the controller. Keep the grounding cable as
short as possible.
(3) Mounting location
Design the size of the control panel and the installation type so that the temperature surrounding the
controller is 40oC or less.
Mount the controller vertically on the wall with 30mm or 50 more of space on the top and bottom of
the controller as shown below.
Allow 60mm or more of space between the front of the controller and the cover of the control cabinet
to allow access to the connectors.
Leave enough space between the controllers so that the operating temperatures of the controllers
stay within the specification range.
Avoid mounting the controller near a vibration source, such as a large electromagnetic contactor or
circuit fuse breaker on the same panel, or keep it away from the controller.
Caution
If the mounting surface for the controller is not flat or is uneven, excessive stress can be applied to
the case, which can cause failure. Mount on a flat surface.
30mm or longer
30mm or more (screw mounting)
50mm or more (DIN rail mounting)
Controller
Door (Lid)
0mm or more (Actuator body size 16 or less, all size of LEH series is applicable)
10mm or more (Actuator body size 25 or more)
60mm or longer
Controller
Shared grounding --- Not acceptable
Controller
Other
equipment
Dedicated grounding --- Good
Controller
Other
equipment
D-class
grounding

- 17 -
4. Initial Setting method
Appropriate setting is required in order to establish the communication of the controller (JXCP1) on the
PROFINET network.
The required initial setting and setting method are explained below. Please refer to the SIEMENS PLC
setting software "SIMATIC Manager Version 5.5 (hereinafter referred to as STEP7)", the representative
PROFINET master device as an example.
Please note that this controller, PLC and PC should be wired correctly in accordance with "5. External
Connections", "6.CN1: Power Supply Plug".
The required setting method such as GSDML file installation varies depending on which setting software
will be used, so if the software other than STEP7 is used, please refer to the operation manual of the
applicable setting software.
4.1 GSDML file and icons
A GSDML file is required by the setting software, to configure the JXCP1 for a PROFINET network
Furthermore, special icons are necessary for the display of the JXCP1 controller within the setting
software.
GSDML file and special icons can be downloaded from the URL below.
URL http://www.smcworld.com
Document/ download→Operation Manuals →Electric Actuator →JXCP1 →Configuration
File
4.2 GSDML file installation
The following instructions describe how to install a GSDML file using the STEP7(SIMATIC Manager)
setting software.
(1) Start the STEP7 application, and insert the applicable station from the menu [Insert] →[Station]. Click
on the Station icon to see the Hardware icon. Please double-click this icon to start [HW Config], a
new window will open.
Fig. 4.1 HW Config startup screen
(2) Select [Options/ Install GSD file...] from the HW Config menu.
Fig. 4.2 Selection of [Install GSD file] of HW Config

- 18 -
(3) Specify the path of the JXCP1 GSDML file and click the [Install] button.
(The GSDML file for JXCP1 can be downloaded from the SMC website (http://www.smcworld.com).
Fig.4.3 Installation of GSDML file
4.3 Addition of JXCP1 controller to PROFINET network
(1) Start [HW Config] from STEP7(SIMATIC Manager). (Refer to 4.2(1).)
Add the appropriate master (PLC) and the PROFINET bus to the hardware configuration screen.
(please refer to the STEP 7 user manual for instructions).
Locate the JXCP1 controller icon in the hardware catalogue (right screen), it is under [PROFINET IO],
[Additional Field Device], [Controllers], [SMC JXC])
Drag the icon from the hardware catalogue and drop it on the PROFINET-IO-System line
(PROFINET network).
Fig. 4.4 Addition of JXCP1 to PROFINET network
Hardware Catalogue
PROFINET-IO-System line (Bus)
JXCP.xm
l
JXCP1

- 19 -
(2) Double-click the JXCP1 icon on the PROFINET network.
When the Properties screen appears, set an arbitrary name in the [device Name] field. To set the IP
address, click [Ethernet] button and enter an arbitrary address.
Note: when the Properties screen below appears for the first time, it may automatically
display a device name and an IP address. If the default description is acceptable, it is
not necessary to change it.
Click [OK].
Fig.4.5 Device name and IP address input screen
(3) When other settings such as master and device are added and their settings are complete, please
select [PLC/Download] and download (1) to (3) setting to the PLC.
4.4 Registration of the device name of the JXCP1 controller to be connected
(1) Start [HW Config] from STEP7(SIMATIC Manager). (Refer to 4.2(1).)
Select [PLC]→[Ethernet]→[Edit Ethernet Node] from the menu bar of [HW Config].
Fig.4.6 [Edit Ethernet Node] screen is selected.