Litelume Econolume Series User manual

Strip Linear
Econolume Series (8ft)
Installation Instructions
LITELUME™ seeks to deliver the most advanced and efficient LED technology. Due to
technology progression, specifications may change. We reserve the right to update product
specifications without notice. Contact LITELUME™ for the most up-to-date data.
www.litelume.com
[email protected]
833.LED.LUME
Page 1/4
Rev Date: 08/23/2018
©Lite Lume Corporation 2018
Warning
1.To avoid electric shock, disconnect power at source prior to installation.
2.The installation should be performed by qualified electricians or lighting technicians.
3.Before conducting any installation, maintenance, or removal, disable all power to the luminaries and wait until the fixture cool
down.
4.Do not touch the fixture while it is in service.
5.If there is any problem with the fixture, DO turn off power and DO NOT attempt repair unless you are a qualified technician or
the customer service member.
Surface Mount Installation
1. Unscrew the 4pcs screws on the back box of the luminaire or the luminaire base.
Luminaire Base
Screw(4Pcs)
2. Disconnect the wire plug to start installation.
Luminaire Base
Plug
Lensand Metal Lens
Frame Assembly

Strip Linear
Econolume Series (8ft)
Installation Instructions
LITELUME™ seeks to deliver the most advanced and efficient LED technology. Due to
technology progression, specifications may change. We reserve the right to update product
specifications without notice. Contact LITELUME™ for the most up-to-date data.
www.litelume.com
[email protected]
833.LED.LUME
Page 2/4
Rev Date: 08/23/2018
©Lite Lume Corporation 2018
3. Install and lock the mounting plate on the luminaire base following the arrow.
LNGND
DIM+ DIM-
4. Connect the AC wires and dimming wires.
Wire box in the celling
5. After wire connection complete, Fix the screws on the ceiling.
Wire box in the cellingc elling

Strip Linear
Econolume Series (8ft)
Installation Instructions
LITELUME™ seeks to deliver the most advanced and efficient LED technology. Due to
technology progression, specifications may change. We reserve the right to update product
specifications without notice. Contact LITELUME™ for the most up-to-date data.
www.litelume.com
[email protected]
833.LED.LUME
Page 3/4
Rev Date: 08/23/2018
©Lite Lume Corporation 2018
6. Align the holes of the fixture with the screws one the ceiling and slide it to the side to lock the fixture.
Wire box in the cellingc elling
Chain Mount Installation
1. Clip the aircraft cable into the planned holes.
2. Adjust the cables to achieve balance.

Strip Linear
Econolume Series (8ft)
Installation Instructions
LITELUME™ seeks to deliver the most advanced and efficient LED technology. Due to
technology progression, specifications may change. We reserve the right to update product
specifications without notice. Contact LITELUME™ for the most up-to-date data.
www.litelume.com
[email protected]
833.LED.LUME
Page 4/4
Rev Date: 08/23/2018
©Lite Lume Corporation 2018
3. Connect the AC wires and dimming wires.
LNGND
DIM+DIM-
4. Wrap the wires with metal conduit.
Metal Hose
Wiring Diagram
For 0-10V Dimming Version, please refer to wiring diagram below.
LIGHT
FIXTURE
Cleaning and Maintenance
CAUTION: Be sure the fixture temperature is cool enough to touch. Do not clean or maintain while fixture is energized.
1. Clean glass lens with non-abrasive glass cleaning solution.
2. Do not open the fixture to clean the LED. Do no touch the LEDs.
Troubleshooting
1. Check that the line voltage at the fixture is correct. Refer to wiring diagram above.
2. Is the fixture grounded properly?
3. Be sure the photocell, if used, is functioning properly.