Litemax Electronics PPS1831 Series User manual

1
PPS1831 Series User Manual
(1st Edition June/14/2012)
(Version:V1.5)
All information is subject to change without notice.
Approved by Checked by Prepared by





LITEMAX ElectronicsInc.
7F‐1,No.135,Lane235,Bau‐chiauRd.,Shin‐dian
Dist.,NewTaipeiCity,23145Taiwan.
Tel:886‐2‐8919‐1858
Fax:886‐2‐8919‐1300
Homepage:http://www.litemax.com/


2
Record of Revision
Version DateRemark
1.1Mar/30/2012InitialRelease
1.2Apr/02/2012SecondVersion
1.3Apr/04/2012ThirdVersion
1.4May/22/2012FourthVersion
1.5June/14/2012 FifthVersion
 

3
Copyright Notice
This document is copyrighted, 2012. All rights are reserved. The original
manufacturer reserves the right to make improvements to the product. The
information contained in this document is subject to change without notice.
This Document contains proprietary information that is protected by copyright.
No part of this document may be photocopied, reproduced, translated, or
transmitted in any form or by any means without the prior written permission of
the original manufacturer. Information provided in this document is intended to
be accurate and reliable. However, the original manufacturer assumes no
responsibility for its use, nor for any infringements upon the rights of third parties,
which may result from its use.
The material in this document is for product information only, the original
manufacturer reserves the right to make change in the product design without
notice to its users. While reasonable efforts have been made in the preparation
of this document to assure its accuracy, original manufacturer assumes no
liabilities resulting from errors or omissions in this document, or from the use of
the information contained herein.

4
Safety and Warranty
1. To disconnect the machine from the electrical power supply, turn off the power switch and
remove the power cord plug from the wall socket. The wall socket must be easily accessible
and in close proximity to the machine.
2. Read these instructions carefully. Save these instructions for future reference.
3. Make sure the voltage of the power source is correct before connecting the equipment to
the power outlet. This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult your dealer or local
power company.
4. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray
detergents for cleaning. Use a damp cloth.
5. Follow all warnings and instructions marked on the product.
6. Do not use this product near water.
7. Do not place this product on an unstable cart, stand, or table. The product may fall, causing
serious damage to the product.
8. Slots and openings in the cabinet and the back or bottom are provided for ventilation; to
ensure reliable operation of the product and to protect it from overheating. These openings
must not be blocked or covered. The openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This product should never be placed near
or over a radiator or heat register, or in a built-in installation unless proper ventilation is
provided.
9. Do not allow anything to rest on the power cord. Do not locate this product where persons
will walk on the cord.
10. Never push objects of any kind into this product through cabinet slots as they may touch
dangerous voltage points or short out parts that could result in a fire or electric shock. Never
spill liquid of any kind on the product.
11. Never pour any liquid into an opening. This could cause fire or electrical shock.
12. Never open the equipment. For safety reasons, only qualified service personnel should
open the equipment.
13. If any of the following situations arises, get the equipment checked by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according to the user's
manual.
e. The equipment has been dropped and damaged.

5
Safety Symbol Description
The following safety symbols are the further explanations for your reference.

6
for FCC 15b devices
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Part 15.21 information for user
You are cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.

7
Legislation RoHS and WEEE Symbol
Restriction of the use of certain Hazardous Substances
This product uses components that comply with the requirements of the Restriction of the use
of certain Hazardous Substances (RoHS) Directive 2002/95/ EC.
WEEE
2002/96/EC Waste Electrical and Electronic Equipment Directive on the treatment,
collection, recycling and disposal of electric and electronic devices and their
components.
The crossed dustbin symbol on the device means that it should not be disposed of with other
household wastes at the end of its working life. Instead, the device should be taken to the
waste collection centers for activation of the treatment, collection, recycling and disposal
procedure.
To prevent possible harm to the environment or human health from uncontrolled waste
disposal, please separate this from other types of wastes and recycle it responsibly to
promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their
local government office, for details of where and how they can take this item for
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract.
This product should not be mixed with other commercial wastes for disposal.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must accept
any interference received, including interference that may cause
undesired operation.

8
Acknowledgments
Intel®, CoreTM 2 Duo / Celeron are registered trademarks of Intel®
Corporation.
IBM, PC/AT, PS/2 are trademarks of International Business Machines
Corporation.
Microsoft® Windows is a registered trademark of Microsoft®
Corporation.
RTL is a trademark of Realtek Semi-Conductor Co., Ltd.
C&T is a trademark of Chips and Technologies, Inc.
UMC is a trademark of United Microelectronics Corporation.
ITE is a trademark of Integrated Technology Express, Inc.
All other product names or trademarks are properties of their respective
owners.

9
Table of Contents
1. Item Checklist........................................................................... 11
2. General Information..................................................................13
2.1 Introduction.......................................................................13
2.2 Feature..............................................................................13
2.3 Specification......................................................................14
2.4 System View .....................................................................15
2.5 Product Dimension............................................................17
3. Hardware Installation and Power on/off....................................19
3.1 Safety Precautions............................................................19
3.2 HDD Installation................................................................19
3.3 CF Card Installation..........................................................21
3.4 Telephone Set Installation.................................................22
3.5 MSR Installation................................................................23
3.6 Power on/off Operation.....................................................24
4. BIOS Setting.............................................................................25
4.1 Main Feature Setup ..........................................................25
4.2 Advance Chipset Setup ...................................................25
4.3 Chipset Feature Setup......................................................26
4.4 Boot Devices Setup ..........................................................26
4.5 Security and Password Setup...........................................27
4.6 Save and Exit Option........................................................27
5. Driver Installation......................................................................28
5.1 Wireless LAN Driver Installation........................................28
5.2 Card Reader Driver Installation.........................................35

10
6. OSD Setting .............................................................................44
6.1 Brightness Menu...............................................................44
6.2 Audio Menu.......................................................................45
6.3 Auto Color Menu...............................................................46
6.4 Color Temperature Menu ..................................................46
6.5 Auto Adjust Menu..............................................................47

11
1. Item Checklist
Take out the system unit from the carton. Remove the unit by carefully clutching the foam
inserts and remove slowly to protect the system. The following contents should be found in
the carton:
1 x PPS Series Panel PC
1xIPPhoneSet
1 x CD for User Manual and Driver
1xAC/DCAdaptor
If any of these items should be missing or damaged, please contact your distributor or sales
representative immediately.
PPS Panel PC
Landscape Portrait
IP Phone Set

12
AC/DC Power Adaptor
CD for User Manual and Touch Driver
Packing

13
2.0 General Information
2.1 Introduction
The intended use of the Litemax’s “Infotainment System：PPS1831”is made for
the security staff and care takers in daycare, hospital and clinical settings for
monitoring.
PPS1831 is 18.5 inch fanless multi function panel PC, feature power efficient Intel
embedded processor and advance long life LED backlight display. With projective
capacity multi touch, wireless connectivity, smart card reader and VOIP telephone,
PPS1831 provide infotainment solution at the same time.
The PPS1831 is a general purpose panel PC with Intel® Atom processor-based
computer that is designed to serve as a point of care station, bed side terminal or
multi-function computer. It is a PC-based system with 18.5" true color TFT LCD
display, Zero Noise solution; integrated multimedia functions make them the
perfect platforms to build comprehensive lifestyle computing applications.
The PPS1831 includes all the features of a powerful computer into a slim and
attractive chassis. The PPS1831 support 2.5” Hard Disk Drive storage function
and one Mini-PCI for WLAN expansion. Moreover, they feature flexible I/O ports,
such as six USB2.0, one RS-232, two RJ45 for GbE.
Convenient operation, Silent, compact, mobility and highly integrated multimedia
system let you to focus on healthcare utility, interactive information displays,
automation control systems, general desktop usage, multimedia recreation, and
other medical requirements.
2.2 Features
18.5” TFT LCD panel PC with 1366x768 resolution
LED backlight with low power consumption and constant brightness
Landscape & Portrait display mode support
Fan-less design provides silent operation, zero noise.
Projective capacitive multi-touch screen provides easy and intuitive interactions
withapplication
Easily access swappable HDD and CF slot.
VOIP telephone provides data and telephone communication onto a common
network.
CMOS 1.3MP PC camera provides clear photo taken and motion monitoring
Smart Card Reader (SCR) and RFID enable electronic record.
Wireless LAN and cable LAN provide flexible network connection
Bluetooth module provides easily wireless connection
IP54 same level facial screen with antibacterial coating provide water proof feature
And reduce bacterial buildup.
Optional Features:
RFID and SCR combo reader.
DVB-T and ATSC TV receiver support.
IP Phone.

14
2.3 Specification
Model Number PPS1831
Description 18.5" Fanless, Intel® ATOM™ D510 1.66GHz Processor,
Multi-Function Panel PC
Display 18.5" Wide LED Backlight
Active Display Area 304.128x228.096 mm
Brightness 250 cd/m2
Resolution 1366x768 (HD)
Touch Screen Projective Capacitive Multi-Touch
Computing Platform
Processor Intel® Atom D510 1.66GHz
Chip Set Intel® ICH8M
Memory SODIMM DDRII 533/667 Memory up to 2GB
Ethernet Gigabit Ethernet x 2
Storage 2.5” SATAII HDD drive bay
CF to SATAII socket module (optional)
External
Connectivity
X2 RJ-45 Gigabit Ethernet (GbE)
X4 USB2.0
X1 COM port RS232
X1 Audio Mic-in, Line-out
X1 Smart Card Reader
X2 RJ-11 (at right and left side)
X1 Four pins DC Input connector
X1 DVB-TAntenna connector (IEC type)
Internal Connectivity
Speaker: 2x2W stereo speaker
Internal Microphone: Build in
PC Camera: USB Video Class (UVC) compliant camera module
Bluetooth: Bluetooth v2.0 + EDR
Wireless LAN: WiFi 802.11 b/g
OSD: (4 keys and 1 LED)
Power on/off button, Power LED, Manual, Volume (+), Volume (-)
Optional Features
IP Phone: Internet Softphone
DVB-T: Digital Video Broadcasting-Terrestrial
DAB: Digital Audio Broadcasting
RFID: Standard protocol Mifare classic
Smart Card Interface: Standard protocol ISO7816-3 ,EMV L1
Power
Voltage DC Input: DC 12V
Power Adaptor DC 12V Output AC100V~240V (120Watt)
Mechanical
IP Rating Front IP65 standards when console mounted.

15
Construction Antibacterial plastic housing
Mounting VESA75/VESA100
Dimension 447.2x302.9.7x58.98 mm
Net Weight 5.4Kg
Environmental
Operating
Temperature 0°C~40°C
Storage Temperature -20°C ~ 60°C
Operating Humidity 5~95% @ 40°C, non-condensing
2.4 System View
2.4.1 Front View

16
2.4.2 Rear View
2.4.3 Buttom View

17
2.5 Product Dimension


18

19
3.0 Hardware Installation and Power on/off
3.1 Safety Precautions
Always completely disconnect the power cord from your board whenever you are working
on it. Do not make connections while the power is on, because a sudden rush of power
can damage sensitive electronic components.
Always ground yourself to remove any static charge before touching the board. Modern
electronic devices are very sensitive to static electric charges. Use a grounding wrist
strap at all times. Place all electronic components on a static-dissipative surface or in a
static-shielded bag when they are not in the chassis
3.2 HDD Installation
3.2.1 Remove the HDD cover screw.
3.2.2 Assembly 2.5” HDD on the HDD carrier metal.

20
3.2.2 Push HDD set into the HDD housing, the connector of HDD toward the
housing.
3.2.3 Make sure HDD is connected properly with HDD bay, and then close HDD cover
with screw.