Qbic Technology Luminen 8 User manual

CARE AND WARNING
type
CAUTION
Ris of explosion if the battery is replaced by an incorrect
Wait one-half hour after switching off before
handling parts
Qbic Technology Co.,Ltd.
26F.-12,No.99.Sec.1, Xintai 5th Rd., Xizhi Dist., New Taipei Cith 221, Taiwan(R.O.C)
Tel: [phone] FAX: [phone]
QHCXXXXXXXXXX
NOTE : Operating Temperature: 0°~ 40°C
Power adapter information:
Input: 100-240V~50/60Hz 0.5A
Output: 12V 1.0A
Power information:
Input: PoE 44V - 54V 0.3A
WARNING :
Changes or modifications to this unit not expressly approved by the party responsible for compliance will void the user’s authority to
operate the equipment.
◎◎NOTE :
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/panel PC technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
•May not cause harmful interference.
•Must accept any interference received, including interference that may cause undesired operation.
◎Correct disposal of this product :
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of
material resources. To return your used device, use the return and collection systems or contact the retailer where the product was
purchased. They can take this product for environmental safe recycling.
◎The power consumption of the product in networked standby is 3.3W which all wired network ports are connected and all wireless
network ports are activated.
◎The product is to be connected only to PoE networks without routing to the outside plant.
◎FCC & CE RF radiation Exposure Statement Caution :
To maintain compliance with the FCC & CE`s RF exposure guidelines. Place the product at least 20cm from nearby persons.
◎Replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types);
Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion; Leaving a
battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid
or gas; A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
◎This unit is intended to be supplied by an UL / IEC 62368-1 certified Class II power adapter suitable for use at minimum 40 degree C and
altitude of operation up to 5,000 m whose output complied with LPS/PS2 and meets ES1, and is rated 12 V d.c., minimum 1.5 A or
UL/IEC 62368-1 certified PoE output power supply suitable for use at minimum 40 degree C and altitude of operation up to 5,000 m
whose output complied with LPS/PS2 and meets ES1 and is rated 44-57 V d.c., minimum 0.4 A
◎Canada, Industry Canada (IC) Notices
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Canada, avis d'Industry Canada (IC)
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développe-
ment économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
1. L’appareil ne doit pas produire de brouillage;
L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionne-
ment.
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless
Device should be used in such a manner such that the potential for human contact during normal operation is minimized.
This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions. (antennas
are greater than 20cm from a person's body).
Informations concernant l'exposition aux fréquences radio (RF)
La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite d'exposition aux fréquences radio d'Industry Canada (IC).
Utilisez l’appareil de sans fil de façon à minimiser les contacts humains lors du fonctionnement normal.
Ce périphérique a également été évalué et démontré conforme aux limites d'exposition aux RF d'IC dans des conditions d'exposition à
des appareils mobiles (antennes sont supérieures à 20 cm à partir du corps d'une personne).
Quick Start Guide
Luminen 8
(HC-0850N-PW)
Touch Panel PC
Support site
This quick guide will help you go through installation quickly

LASER
1
The ambient light sensor can automatically adjust panel brightness base on the environment. See Display
Settings to enable automatic brightness.
The Laser proximity sensor will detec nearby motion to wake the panel up without requiring a touch.
LASER SAFETY:
This product complies with FDA performance standards for laser products except for conformance with IEC
60825-1 Ed. 3., as described in Laser Notice No. 56, dated May 8, 2019.
Date of manufacture: the date code shown on the product label represents the manufacturing date of this laser
product.
CAUTION: Invisible laser radiation when open. Avoid exposure to beam. Class 1 laser product. This system must
be opened only by qualified technicians to prevent accidents caused by the laser beam.
CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
S/N : 0123456789 MADE IN TAIWANNOV/2022NOV/2022
-Month/Year
CAUTION: This product is only suitable for insatllations less than or equal to 2m(6.56ft) high for CE/UL safety.
1
2
5
4 12
10
2
3
6
8 9 11
6
77
DC Power Adapter
(Optional)
1 2
Contents Installation
Indication
Display
Panel PC
(HC-0850N-POE)
Bracket M2.5 screw *1
M3.2 screw *3
1
Mic2
Sensors3
Home Button4
Reset Button5
Speaker6
Light Bar
7
RJ45 / POE8
DC 12V
9
USB Micro-AB
10
Restore Button11
Camera12
STEP 1
Fasten M3.2 screw *2 to secure
the bracket to gang box.
STEP 2
Mount the Panel PC on the bracket.
STEP 3
Fasten M2.5 screw *1 to secure
the Panel PC to bracket.