Litemover DMX Automated Universal Remote Head Operator's manual

Manual and safety instructions
Copyright Litemover BV, 2022-2.4

1
Litemover manual and safety instructions
Be aware that you are moving an object like a (large) lighting fixture on a distance.
When using the Litemover always have the moving fixture in clear eyesight.
When using the Litemover upside-down, with a light fixture hanging below the Litemover,
ALWAYS USE AN ADEQUATE EXTRA SAFETY CHAIN
.
Maximum Weight Load 220 lbs. / 100kg.
12 VDC / 4 Amp. max.
For professional use only.
Do not operate this machine unless you completely read and understood this manual and
safety instructions and act according to them.

2
Index.
Litemover set 4
Litemover on a stand 5
Litemover in a hanging position 7
Focus Motor on an ARRI M90 fixture 9
Focus Motor on an ArriMax 12/18 kW fixture 10
Tilt motor 12
Connectors 13
90˚ connector 14
Side rails 15
Battery 16
Operating possibilities 17
Manual factory reset 20
DMX / CRMX control 21
DMX table 21
RDM 24
RDM setting 26
Dealers 28

3
Case content.

4
Litemover set.
1. Pan motor unit.
2. Tilt motor unit
3. Focus Motor unit.
4. ‘Hand’ connector
5. ‘Pin’ connector
6. ‘Clamp’ connector
7. 90˚coupler
8. 4x 15 mm. rod 50 cm.
9. 2x 15 mm. rod 25 cm.
10. Manual control unit
11. V-Lock Battery unit
12. Blueshape PSU (V-lock battery shape)
(Not in the pictures on the left, but part of the set)
Focus motor connector cable
Remote/Power cable 25 ft.
Battery DC cable
IEC cable

5
Litemover on a stand.
1.
Put the
Pan unit
of the Litemover
on the
stand
2.
Put the
yoke
of the light on the Pan
unit
3.
Attach
2 rods
by screwing them in
the Pan unit

6
4.
Slide the
Tilt motor
over the rods,
and plug the cable in the Pan unit
5.
Connect
the tilt motor to the front
of the light fixture and
PULL BACK
to the maximum desired ‘tilt down’
position.
6.
Place the
Focus motor
on the
backside of the light fixture and
connect the cable between Focus
motor and Pan unit.

7
Litemover in a hanging position.
1.
Hang
the light fixture on the Pan unit
2.
Attach 2 long rods by screwing
them in the Pan unit.
3.
Attach the
90˚connector
and
slide
the Tilt motor over the rods
pointing down and plug the cables
in

8
4.
Place the Focus motor on the
backside of the light fixture and
connect the cable between the
Focus motor and the Pan unit.
5.
ALWAYS SECURE
your hanging
fixture with
EXTRA SAFETY CABLE
!
6.
Connect the ballast or power cable
of your light fixture on one of the
side rails of the Pan unit.

9
Focus Motor on an ARRI M90 fixture.
The Focus motor slides over the focus knot of the ARRI M90 fixture

10
Focus Motor on an ArriMax 12/18 kW fixture.
The Focus motor slides in the focus wheel of the ArriMax 12/18 kW. or 12/24 kW. Fresnel fixture

11

12
Tilt motor.
The tilt motor can be placed in a desired position on the two rods behind the main unit.

13
Connectors.
Hand connector Pin Connector Clamp Connector
coming soon! Connectors which will connect to:
Multi yoke 4x Vortex 8
Mirror connector
K5600 Alpha range

14
90˚ connector.
90˚ connector for using the Litemover in hanging position.

15
Side rails.
Please use the two side rails to connect your wires to Litemover Main unit

16
Battery.
When using DMX or CRMX you can power the Litemover with a V-Lock battery (14,4 Volt)
The V-Lock battery connector also slides over the two rods

17
Operating options.
Operation of Litemover is possible in 3 different ways:
Manual control via the handset via the buttons.
DMX control, hard wired with a dmx cable.
CRMX control, via lumenradio inside.
When powered via the handset, the buttons of the handset also works while DMX or CRMX is present.

18
Manual control via the handset with the combined Power and Signal cable
Status light on the handset:
On = motor movement is detected
Blinking light = Motor is at the end of the tilt or focus movement (overcurrent)
DMX control via DMX cable
CRMX – Timo2
Timo2 (CRMX) control via pushbutton and blue status light:
Off: unlinked
Fast blink: linked, no rf link
Slow blink: linked, rf link, no DMX
On: linked, rf link, DMX reception
Hold button below the status light for 2 sec to unlink Timo2

19