Little Partners LPA200 User manual

PRN: AIM-LPA200-LPN [16.08.11]
A
2 CUBBY
KIDS LOCKER
2 CUBBY
KIDS LOCKER
Important Information:
Before you begin assembly, please read these instructions. See next page for important
warning statements on this product. After product is assembled make sure all bolts and
screws are securely tightened.
Note: Product may vary slightly from images shown.
LPA200
LPA200
LPA1 LLC

KEEP INSTRUCTIONS FOR FUTURE USE
WARNING
Prevent serious injury or death from falls or tipping over
NEVER use this product if there are any loose or missing or
parts. Check after assembly and periodically during use at least once a week
fasteners, loose joints broken
READ all instructions BEFORE assembly and USE of the product
NEVER substitute parts
CONTACT us for replacement parts. See back page for contact info.
NEVER PLACE PRODUCT ON AN ELEVATED SURFACE
ALWAYS place product on a flat, level surface
NEVER place near stairs
ADULT assembly required!
Choking Hazard: Unassembled small parts can be a choking hazard to
children. For the safety of your child it is recommended to not assemble this
unit with them in the same room due to concern they accidently pick up
and swallow small parts.
2
Furniture that is not secured to a wall
could tip over and cause an injury.
This unit includes an anti-tip kit.
BEFORE use, ensure kit is installed
correctly and secured safely to the wall.
See instructions for further information.
DANGER

!Avoid sharp objects.
!Avoid excessive force.
!Make sure to wipe complete unit with a mild soap and damp cloth before the first use.
!Clean with mild soap and damp cloth.
DISMANTLING PRODUCT AND STORAGE
!Follow directions in reverse to dismantle this product.
!Keep all hardware together in a plastic bag and store with the other parts. Store all parts
in a safe and temperature controlled environment.
CARE AND MAINTENANCE
Assemble product on a soft surface like a carpet/rug or blanket to protect finish.
While one person can assemble this item two people are recommended
DO NOT USE POWER TOOLS TO ASSEMBLE THIS
PRODUCT. USE OF POWER TOOLS WILL
INVALIDATE ANY CLAIM AND MAY DAMAGE THIS
PRODUCT MAKING IT UNSAFE.
USING A POWER TOOL CAN CAUSE BOLTS AND
SCREWS TO BE OVER TIGHTENED AND STRIP
HOLES.
3
USEFUL HINTS AND TIPS

PARTS LIST
1
5
3
4
6
7
8
9
10
11
4
1
(LPA200-X-1) x1 (LPA200-X-2) x1
2
3
(LPA200-X-3) x1 (LPA200-X-4) x1
4
6
(LPA200-X-5) x1
(LPA200-X-6) x1
5
(LPA200-X-7) x1
7
(LPA200-X-8) x1
8
(LPA200-X-11) x1 (LPA200-X-12) x1
11 12
(LPA200-X-10) x1
10
2
(LPA200-X-9) x1
9
PPI Label
12
Anti-tip Label
The composite wood products contained in this product comply with the applicable Phase 2
emission standards specified in section 93210.2 (a). California Code of Regulations.
Model :#
Color:
Shipment Ref. #:
Product Packaging Information
PRN: 02-04016 [16.08.10]
LPA1 LLC.
501 South 9th Street
Reading, PA 19602
Toll Free: 1-800-704-9058
[email protected]
MADE IN CHINA
Date Code:

Assembly Hardware supplied (actual size)
HARDWARE
WALL STRAP HARDWARE
J
K
QTY
Name
Ref.
Head
mm 10 20 30 40 50 60 70 80
M4 x 25mm Screw
1.5 x 18mm Nail
8 x 30mm Wood Dowel
8 x 50mm Wood Dowel
4
30
28
4
B
D
E
F
8
M3.5 x 14mm Screw
A
1 "1" 2" " 2 " 3"
15mm Cam Lock 13
CL
Cam Stud 13
CS
Other Parts and Assembly tools (not to Scale)
2
2
4
2
Screwdriver
(NOT supplied)
Hook
Rubber Hammer and Hammer
(NOT supplied)
5
QTY
Name
Ref.
Head
mm 10 20 30 40 50 60 70 80
M3.5 x 14mm Screw
M4 x 40mm Screw
12 x 2mm Plastic Washer
30mm Wall Plug
1
1
2
1
A
L
G
H
1 "1" 2" " 2 " 3"
200 x 25mm Wall Strap 1
I
4 mm “S” Allen Key
M5 x 50mm Allen Head Screw 7
C

1
Insert all wood dowels, and cam locks. Screw in all cam studs
ASSEMBLY INSTRUCTIONS
15mm Cam Lock [x13]
CL
6
8 x 30mm Wood Dowel [x28]
E
8 x 50mm Wood Dowel [x4]
F
Cam Stud [x13]
CS
F
FE
E
E
CL
E
E
CS
CL
CL
CS
CS
CS
1
CS
CS
CS
CS
3
F
F
6
7
8
E
E
E
E
9
E
E
E
E
E
E
E
10
E
E
4
E
E
E
E
CL
CL
CL CL
5
E
E
E
E
CL
CL
CL
CL
CS
E
CL CL
CS
CS
CS
CS
E
2
Make sure arrow is
pointing towards end
of wood
Cam Stud
CS
Tighten with a rubber hammer until no
threads are showing and you cannot turn
any more. DO NOT use power tools.
INSTALLING CAM STUD
INSTALLING CAM LOCKS
Identify arrow on
head. Look closely.
ARROW
Arrow MUST point
toward hole in edge
of panel.
Push cam lock
all the way
down into hole.
12 3

A
AA
A
J
J
6
6
TURN OVER
3
M5 x 50mm Allen Head Screw [x2]
C
2
Assembly of Hooks
7
Hook [x4]
J
AA
A
J
J
1
2
ASSEMBLY INSTRUCTIONS
M3.5 x 14mm Screw [x8]
A
9
8
Make sure there is NO space between panel 8 and 9 when assembled.
C
3a
9
8
K
J
A
A
A
J
A
A

ASSEMBLY INSTRUCTIONS
4
5
7
6
4a
CL
7
8
7
8
6
5
6
TIGHTENING CAM LOCKS
Use screw driver to turn to tighten clock wise( at least past the half way point).
Screw driver
ARROW
a
ARROW
b
c
8

ASSEMBLY INSTRUCTIONS
9
7
10
9
8
5
4
M5 x 50mm Allen Head Screw [x1]
C
CK

ASSEMBLY INSTRUCTIONS
10
9Line up wood dowels and cam bolts with holes
first, then use a rubber hammer to GENTLY join
part 2 with body of locker to ensure NO GAPS
before tightening cam locks.
10
Inside View
2
CL
7
2
7
5
TIGHTENING CAM LOCKS
Use screw driver to turn to tighten clock wise( at least past the half way point).
Screw driver
ARROW
a
ARROW
b
c
7
2
9
10
5
9a
2
9b

ASSEMBLY INSTRUCTIONS
11
11
M5 x 50mm Allen Head Screw [x2]
C
12
9
2
C
K
C
1
7
9
10
5
1
12a
12b
Line up wood dowels and cam bolts with holes
first, then use a rubber hammer to GENTLY join
part 1 with body of locker to ensure NO GAPS
before tightening cam locks.

ASSEMBLY INSTRUCTIONS
12
M5 x 50mm Allen Head Screw [x2]
C
TIGHTENING CAM LOCKS
Use screw driver to turn to tighten clock wise( at least past the half way point).
Screw driver
ARROW
a
ARROW
b
c
13
1
5
7
5
1
14
1
C
K
C
9

2
34
1
CL
2
3
11a
ASSEMBLY INSTRUCTIONS
15 THERE ARE 2 OPTIONS FOR ASSEMBLING THE TOP. SEE BOTH OPTIONS BELOW TO PROCEED
15aASSEMBLY FOR OPTION A TOP overhangs
on front
13
Side view
WALL WITHOUT BASE BOARD
OPTION A - WALL WITHOUT BASE BOARD
TOP overhangs
on front
Side view
WALL WITH BASE BOARD
OPTION B - WALL WITH BASE BOARD
TOP overhangs
on back
BASEBOARD

15bASSEMBLY FOR OPTION B
CL
2
3
2
34
1
12a
ASSEMBLY INSTRUCTIONS
16
1.5 x 18mm Nail [x30]
D
Insert nail into pre-drilled guild hole for easier assembly.
Make sure you are careful to line up nails into center of each
piece of wood.
Assembly complete.
11
2
9
12
11
D
9
1
13a
1
14
TOP overhangs
on back

ŸLocate a wall stud. With the unit against the wall and centered of the
wall stud, mark wall as shown.
ŸCAUTION: The unit must be centered on a wall stud as shown. If you are
unsure of how to locate the wall stud contact a professional contractor.
5 cm
(2 ”)
WALL
ŸMeasure down 5cm from the mark and attach the wall strap to the wall stud
using the screw and washer as shown.
ŸCAUTION: Do not attempt to screw into the plaster wall only. You must also
screw into the wall stud.
Wall Stud
L
17
ATTACHING YOUR UNIT TO THE WALL
I
200 x 25mm Starp (not to scale) [x1]
G
12 x 2mm Plastic Washer [x1]
L
G
I
M4 x 40mm Screw [x1]
OPTION A - WALL STUD
Furniture that is not secured to a wall could tip over and cause an injury.
This unit includes an anti-tip kit. BEFORE use, ensure kit is installed correctly and
secured safely to the wall. See instructions for further information.
DANGER
L
10
G
12 x 2mm Plastic Washer [x1]
17 OPTION B -DRY WALL
ŸWith the unit against the wall mark wall as shown.
WALL
ŸMeasure down 5cm from the mark and drill a 1/8” pilot hole through the wall.
Attach the wall strap to the wall using screw, washer and wall plug as shown.
5 cm
(2 ”)
Drill Required
Percer Nécessaire
Se Necesita Un Taladro
I
200 x 25mm Starp (not to scale) [x1]
H
30mm Wall Plug [x1]
H
I
L
G
M4 x 40mm Screw [x1]
15

ATTACHING YOUR UNIT TO THE WALL
ŸPush the unit up
against the wall lining
up the wall strap with
the opening on the left
panel of the unit.
Back Side of Unit
11
FRONT VIEW
I
Ÿ
to the underside of the unit top
using 12mm screw and washer
as shown.
Attach the end of the wall strap
18 19
3
A
I
G
G
12 x 2mm Plastic Washer [x1]
FRONT VIEW
3
11
M3.5 x 14mm Screw [x1]
A
ATTACHING ONE LOCKER TO THE ANOTHER LOCKER
20
M4 x 25mm Screw [x4]
B
21
2
B
B
16
Your unit is pre-drilled with guide holes should you purchase
a second Cubby Locker and want to join them together for
added stability and safet.

LPA1 LLC.
501 South 9th Street
Reading, PA 19602
Toll Free: 800-704-9058
[email protected]
PRODUCT PACKAGING INFORMATION
The following packaging information is also found on Part 11.
11
17
PRODUCT LIMITED WARRANTY
Who is covered by this warranty?
This warranty extends to the original purchaser only and will need proof of
purchase.
Time period of this warranty.
The 1 year term of this warranty shall commence on the date of the original
purchase.
What is covered by this warranty?
The warranty covers any defects, malfunction or failure attributed to either the
quality of materials used, workmanship of finish, or assembly. If during the first 1 year
after purchase of this product under reasonable and non-commercial use, and
conditions of maintained, it fails to conform to this warranty, LPA1 LLC. will at its
option, repair or replace the product determined to be defective.
What is Not Covered by this warranty?
This warranty does not cover damages or malfunctions not resulting from defects in
material or workmanship. Damages or malfunctions from other than normal use,
including, but not limited to, repair or tampering by unauthorized parties.
If you require service.
Find below our contact detail and Product Packaging information when calling us.
This LPA1 LLC. product is made from wood and as such slight imperfections may
occur that are not manufacturing defects. These are the characteristics that make
wood furniture unique and memorable. Remember, in a forest no tree is the same!
The composite wood products contained in this product comply with the applicable Phase 2
emission standards specified in section 93210.2 (a). California Code of Regulations.
Model :#
Color:
Shipment Ref. #:
Product Packaging Information
PRN: 02-04016 [16.08.10]
LPA1 LLC.
501 South 9th Street
Reading, PA 19602
Toll Free: 1-800-704-9058
[email protected]
MADE IN CHINA
Date Code:
MADE IN CHINA
Model :#
Color:
Shipment Ref. #:
Date Code:
The composite wood products contained in this product comply with the applicable Phase 2
emission standards specified in section 93210.2 (a). California Code of Regulations.
Model :# Color: Shipment Ref. #:
Product Packaging Information
PRN: 02-04016 [16.08.10]
LPA1 LLC. 501 South 9th Street Reading, PA 19602 Toll Free: 1-800-704-9058 [email protected] MADE IN CHINA
Date Code: