Livescribe Sky WiFi Installation guide

Smartpen #: Activation Code:

2
Setting up your Smartpen
*Make sure to not skip pages unless informed it is an option*
1. Plug in your Smartpen into your computer by using the provided
USB Cable
2. Go to livescribe.com/setup
3. Enter in the requested information and click Create Account
Turn page

3
4. Link up to Evernote
5. Enter in your e-mail address and a password to create an
account
Turn page

4
6. Using the drop down menu indicate how long you want Evernote
to have access to your account/email. Then click on the
Authorize button
1
2
Turn page or
skip to page 8
** IMPORTANT NOTE: After you authorize Evernote you may
be directed to activate your smart pen by putting in a code.
( See page 8 step #1 under Activating your Smartpen ) If this
is the case, you can choose to come back and complete
steps 7-13 at a later time. **
READ
THIS

5
7. You will get an e-mail to download the app onto your phone or
computer
Helpful Note: The e-mail that will be
sent to you will probably look like one
of these two print screens
8. Install the program by clicking Run
OR
Turn page

6
9. Check the Accept Terms box and click Install
10. Click the Finish (or Get Started) button once the program
gets done installing
1
2
** IMPORTANT NOTE: After you run the program you may be directed to activate
your smart pen by putting in a code ( See page 8 step #1 under Activating your
Smartpen ) If this is the case, you can choose to come back and complete steps
11-13 at a later time. **

7
11. Go to the Start Menu and search for Evernote
12. Click on the Already have an account tab and enter in your
information
Turn page

8
GETTING AN
ALREADY
REGISTERED
MESSAGE? If you
get a message
that says the pen
is already
registered after
you hit Activate
Smartpen follow
the steps on the
below link to
deactivate the
pen
http://livescribe.custh
elp.com/app/answers/
detail/a_id/165
Once the
deactivation is
complete, try
hitting Activate
Smartpen on this
page again. **
Note: you will
need wifi/hotspot
connection.
13. This window will pop up…
Activating your Smartpen
1. You will be directed to enter in a code to activate your smart
pen. This code should pop up on your smart pen window when
you power on your pen.
Helpful Note: To get back to this page you may have to log back
into your livescribe setup page.
Example if the code says AYE-ARH-MWN-ZQ the code that
that you would type in when prompt would be ARHMWNZQ
(no spaces)
Looking for your code? The code is the last 8 digits of your serial
number listed on the bottom of your box.
Your code is also written on the front page of this manual if you have
picked up this manual in person from the OSD Office.
1
3
2
Turn page

9
2. Next this screen will pop up instructing you to set up WIFI/doing
your first update
WIFI Note: WIFI will not work while on campus .For this reason, it
is STRONGLY recommended that you finish the WiFi/Update
instillation process at home where you can try both instillation
options on this page. Click finish once one of these options are
complete.
**If you do wish to run the update while on campus, follow the
WiFi steps listed under Option Two on page 11. **
Helpful Note: You will more than likely have to update your
Smartpen before you will be able to start using it.
Turn page
STOP!
READ
THIS.

10
Setting up WiFi
** IMPORTANT NOTE** WIFI DOES NOT WORK ON NORMANDALE
NETWORK. So, when you are on campus please turn off the WiFi option
on the Smartpen.
Option One- EASIEST OPTION IF YOU HAVE WIFI
1. Power on your Smartpen and tap the Scan for Networks button
under WIFI Setup Control options in your starter notebook to
connect to a WiFi network
2. Tap the Software Update button on your starter notebook to get
the latest features
**Important Note: if you are using Option 1, skip to page 14 once you
set up WiFi and run your software update. **
Turn page for
WIFI Option Two