Living & Co Waipoua Bedside Table User manual

Job no.
Waipoua Bedside Table
INSTRUCTION MANUAL
Maximum recommended weight 15kgs per drawer
55.1cm
51cm
39.6cm

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
2
60Min
Approximate Assembly Time
1 Person Assembly
Floor Area 3m
x 2m
Required Assembly Space
Tools Required
Assembly Details

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
3
1. For the protection of your furniture, we recommend that the product is
placed on a protected surface during assembly to prevent damage
2. Please check that all parts are present before you start the assembly of
your furniture
3. For ease and speed of assembly, we recommend that you identify all the
parts required for each step before commencing with assembly
4. For larger items, please ensure that you have sufficient space (as
indicated on page 1)
5. We recommend that, where possible, all items are assembled near to the
area in which they will be placed in use, to avoid moving the product
unnecessarily
6. During Assembly please take care not to over-tighten hardware as this
may damage the product
7. Always place the product on a steady and stable surface
8. Do not use the product as a stepladder
9. This product is intended for indoor, household use only as it is a non-
industrial product
✓Please periodically check all fittings and re-tighten as necessary
✓To clean your item, please use a damp cloth and wipe clean
✓Never allow any kind of liquid on your furniture
✓Please do not place hot items (e.g. Hot drinks) directly on to the surface
Tips before you start
Care and Maintenance

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
4
QTY
PART
MEASUREMENTS
NOTES
1
Top
510 x 396 x 25mm
Laminate on one side.
1
LH End
446 x 370 x 15mm
Laminate on one side.
1
RH End
446 x 370 x 15mm
Laminate on one side.
4
Corner Leg
526 x 80 x 25mm
Laminate on both sides.
1
Top Drawer Front
444 x 195 x 15mm
Laminate on one side.
1
Bottom Drawer Front
444 x 215 x 15mm
Laminate on one side.
1
Front Rail
418 x 50 x 15mm
Laminate on one side.
1
Base Shelf
418 x 352 x 15mm
Plain (unfinished).
2
LH Drawer Sides
340 x 160 x 12mm
Laminate on both sides.
2
RH Drawer Sides
340 x 160 x 12mm
Laminate on both sides.
2
Drawer Backs
368 x 155 x 12mm
Laminate on one side.
2
Drawer Bottoms
378 x 339 x 4mm
Laminate on one side.
1
Back Panel
456 x 438 x 4mm
Plain (unfinished).
Parts List
Hardware List
14 x
Connecting
Bolts
10 x Large
Cams
(15mm)
4 x Small
Cams
(12mm)
8 x Drawer
Slide
Screws
8 x Small
Woodscrews
14 x Dowels
2 x 15mm
Panhead
Screws
4 x Nail on
Glides
2 x Metal
Drawer Slide
Sets
20 x 31mm
Large
Woodscrews

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
5
5
The Cam and Connecting Bolt system is used to put your unit together. Below is an explanation of how this
system works.
The Drawer Slide components shown above are to be attached to the cabinet. They have letters CL or CR
stamped on them to indicate left hand or right-hand components. You will need these for steps 1 and 2.
Your pack will contain two sets of Metal Drawer Slides. These are bundled together with adhesive
tape. The set comprises of 4 components. Undo the tape on one set at a time and separate the
parts.
LEFT HAND PART (DL) RIGHT HAND PART (DR)
The Drawer Slide components shown above are attached to the drawer. They have the letters DL
or DR stamped on them to indicate left hand or right-hand components. Put these parts aside for
attaching to the drawer later.
Cam Installation & Operation Guide
Drawer Slides Guide
Use these holes

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
6
•To begin assembly, lay the top finished side down on a clean and clear surface.
•Screw four Connecting Bolts into the holes as shown.
Connecting Bolt
Assembly
STEP 1: Top
Connecting Bolt
Connecting Bolt
Connecting Bolt
Connecting Bolt

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
7
•Screw the legs onto the LH end using the 31mm gold screws. Ensure the guide holes in the end
match up with the guide holes on the leg before inserting the screws.
•Tap the Nail on glides into the base of the legs using the guide holes provided.
Nail on Glides
Finished Edge
STEP 2: Screw Legs to LH End
Nail on Glide
Large Woodscrew
Screw
Large Woodscrew

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
8
•Repeat the previous step with the RH End.
STEP 3: Screw Legs to RH End
Nail on Glide
Large Woodscrew
Screw
Nail on Glide
Large Woodscrew
Finished Edge

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
9
•Screw the LH Cabinet Drawer Slides into the LH End using two Drawer Slide Screws for each
slide (ensure that the end of the slide with the wheel is on the side with the finished edge).
•Insert two Large Cams as shown (make sure the arrow on the top of the Cam points towards the
top edge of the End).
•Push two Dowels into the top edge of the End.
•Screw three Connecting Bolts into the holes as shown.
Connecting Bolt
Connecting Bolt
Large Cam
Drawer Slide Screw
Dowel
Cam
Drawer Slide Screw
Finished Edge
Connecting Bolt
STEP 4: Hardware LH End

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
10
•Repeat the previous step with the RH End.
STEP 5: Hardware RH End
Connecting Bolt
Large Cam
Drawer Slide Screw
Dowel
Cam
Finished Edge
Connecting Bolt
Drawer Slide Screw
Connecting Bolt

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
11
•Install 2 Dowels and 2 Large Cams into each Rail as shown (ensure the arrow on the top of the
Cam points towards the edge of the Rail with the hole in it.
STEP 6: Rail and Shelf
Large Cam
Dowel
Dowel
Dowel
Dowel
Cam
Cam

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
12
•Fit the Front Rail over the Connecting Bolt and tighten the cams as shown on page 5, ensure you
don’t over tighten them, or this may split the side of the rail. Ensure the finished side of the Rail is
facing forward so the cams can’t be seen once the cabinet is completed.
•Fit the Base Shelf over the Connecting Bolt at the bottom of the end and tighten that cams as show
on page 5. Ensure the finished edge is face the front of the end as shown below.
STEP 7: Attach Rails to LH End
Front Edge
Base Shelf
LH End
Front Rail

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
13
•Fit the Connecting Bolts installed in the RH End into the Cams in the Rails and Base Shelf as
shown below.
•Tighten the cams as shown on page 5, ensure you don’t over tighten the cams or this may split the
side of the rail.
STEP 8: Attach RH End
RH End

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
14
•Stand the Bedside upright.
•Fit the Top to the Ends by fitting the four Connecting Bolts installed in the Top into the Cams in the
Ends. Ensure the unfinished edge is facing towards the back. Tighten all four Cams to lock the Top
to the Ends.
STEP 9: Attach Top
Top

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
9
15
•Carefully lay the bedside on its front edge.
•Slide the Back Panel in place.
•Using the two Panhead screws provided, secure the Back Panel in place. Then stand the Bedside
upright.
STEP 10: Back Panel
Panhead Screw
Panhead Screws

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
9
16
Assemble the Drawers
Drawer Bottom
LH Drawer Side
Drawer Side
RH Drawer Side
Drawer Front

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
10
17
•Install the hardware in the Drawer parts as shown below.
Note: Be sure that the arrow on the Small Cam points to the end of the drawer side nearest it.
STEP 11: Install Hardware
Connecting Bolt
Small Cam
Dowell
Connecting Bolt
DRAWER FRONT
Cam
LH DRAWER SIDE
RH DRAWER SIDE
Dowel
Dowel
Cam

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
18
•Lay the Drawer Front finishes side down on a smooth, clean surface.
•Attach the LH and RH Drawer Sides by fitting them into place over the Connecting Bolts installed in
the Drawer Front.
•Turn the Small Cams in a clockwise direction to lock the Drawer Sides in place.
•Slide the Drawer Bottom into place in the grooves in the Drawer Sides and Drawer Front.
•Fit the Drawer Back into place between the Drawer Sides. The groove in the Drawer Back will fit
over the end of the Drawer Bottom.
•Secure the Drawer Sides to the Drawer Back with four Woodscrews as shown below.
STEP 12: Assemble the Drawer
Large Woodscrew
Screw
Drawer Back
Drawer Bottom
2 x Large
Woodscrews
RH Drawer Side
Dowel
Connecting Bolt
Drawer Front
LH Drawer Side
2 x Large
Woodscrews

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
12
19
•Turn the drawer upside-down as shown and attached the Drawer Slides (DL and DR) with the four
small woodscrews as shown below. Ensure that the ends of the slides without the wheels are hard up
against the back of the Drawer Front. Each slide requires two screws.
STEP 13: Attach the Drawer Slides
Small woodscrew
RH Drawer Slide (DR)
Small Woodscrew
Small woodscrew
LH Drawer Slide (DL)

20
•Fit the drawers into the Bedside. Make sure that the rollers at the back of the drawer go behind the
front rollers in the cabinet and into the channel of the drawer slide. It helps to lift the front of the
drawer up a little when doing this.
STEP 14: Insert the Drawers
Congratulations, your Waipoua 2 Drawer Bedside is now complete.
Thank you for supporting New Zealand Made furniture.
Angle the drawer slightly to ensure
that the wheel at the back of the
drawer slide goes behind the front
wheel on the cabinet slide. Then lift the
drawer up and slide it into the
channel of the drawer slide.
AFTER SALES SUPPORT
[e-mail] or 0800 100 858