Living Essentials 005-524 User manual

USER
USER’
’S
SMANUAL MANUAL
PLEASE DO NOT RETURN PRODUCT TO THE STORE.
If you have any problem or concerns, please feel free to contact our customer
service department. We will reply you as soon as possible.
E-Mail: [e-mail]
Tel: [phone] Ext.100
TELTEL: 9095901000
[email protected]

Contents
1. Product Brief............................................................................................. 1
2. Security Precautions and Warning............................................................ 2
3. Installation Instructions............................................................................. 5
4. Using Instructions......................................................................................8
5. Routine Maintenance and Instructions....................................................11

1
1. Product Brief
Product name: Single function Motorized Treadmill
Main parameters and parts list
No.
Parameters Names
Description
1
Input power voltage
110V～
2
Rated frequency
50-60Hz
3
Rated power
1.5HP
4
Speed
0.8-12km/h
5
Running surface
15.8*43.3 inch
6
Max user weight
240LBS
7
Expand dimensions
52*24*40 inch
Packing list
No.
Name
Units
Qty
No.
Name
Units
Qty
1
Complete machine
pc
1
2
Accessory Bag
pc
1
Accessory Bag list
No.
Name
Units
Qty
No.
Name
Units
Qty
1
Inner hexagon wrench 6mm
pc
1
6
Safety Key
pc
1
2
Inner hexagon wrench 5mm
pc
1
7
Silicon oil
pc
1
3
Combination wrench
pc
1
8
User manual
pc
1
4
Screws M6*12
pc
4
9
Mp3 Cable
pc
1
5
Screws M8*25
pc
2
10
Plum knob M10*20
pc
1

2
Notice:
2. Security Precautions and Warnings
Tip: Before folding the treadmill, make sure that the surface incline is "zero".
Please read the instructions carefully before use.
This treadmill is for indoor use and storage only. Avoid spilling water on it or placing it in
damp areas.
Please wear suitable workout clothes and sneakers before exercise. Do not exercise on the
treadmill barefoot.
The attached high power plug cord must be touching the ground when plugged in. Treadmill
cord should be plugged into one dedicated electric outlet/circuit, do not share the electric plug
outlet you are using for your treadmill with other electrical equipment.
Keep children away from the machine to avoid accidents.
Avoid using the machine for uninterrupted long periods of time, as this will overload the
operation and cause damage to the motor and controller, and will accelerate the deterioration of
the bearing, running belt and running board.The treadmill should be maintained regularly per
the instructions listed throughout the manual.
Keep machine away from areas with high levels of dust to avoid strong static.
Please turn off the treadmill by switching off the electric power after using.
Please ensure you are running in a well ventilated area.
Please clamp the security lock cable on your clothing to make sure the machine stops in the
event of any emergency situation.
If you do not feel well while using this machine, please stop and consult a doctor.
The included silicone lubrication must be kept away from children after use.
If the power cord is damaged, please contact our qualified maintenance personnel
for service rather than disassemble it at [email protected].
Forbidden
Don't use the machine if the outer protective shell is broken or has broken off, leaving any part
of the internal structure exposed, or if the welding parts have fallen off or appear as if theymay
fall off.
!

3
---- Otherwise an accident or injury may occur.
Don't jump up and down while the treadmill is in motion.
---- Injuries may result from falling.
Don't keep machine in or near moist/damp space such as thebathroom.
Don’t place machine in direct sunlight, or high temperature places such as near a stove or a
heating appliance.
----Otherwise it may cause leakage and burst into flames.
Don't use if the power cord is damaged or the power plug pin is loose.
----Otherwise this will lead to an electric shock, short circuit or fire.
Don't damage, forcefully bend or twist the power cord. Don’t place heavy objects on the
machine, don't clamp the power cord.
----Otherwise it will cause a fire or you can get an electric shock.
Do not allow more than 1 person use the machine at one time, do not allow others to get close
to the machine while it is in use.
---- Or it may cause an accident or injury due to possible falls.
People who aren’t in a normal conscious state or can’t operate the machine bythemselves
cannot use the treadmill.
----May lead to accident or injury.
Drinking water or pouring water when treadmill is in use/operating is forbidden.
---- May cause electric shock or fire.
People who seldom exercise are advised not to suddenly use the treadmill for any intensive
workout.
Do not use machine, directly after a meal or when feeling tired.
---- This may lead to potential health damage or accidental injury.
This product is suitable for residential use. This product is not recommended for commercial
use, schools, gymnasiums, etc
---- When used for commercial purposes there is a risk of injury.
Don’t use the treadmill when hard objects are in the pockets of your pants or shorts. Remove
them before using the machine.
----Not removing hard objects from your pockets before use may cause accident or injury.

4
Don’t use the treadmill when the power plug is on or near the needle, garbage, or water.
----May cause electric shock, short circuit, or fire. Do not touch the power plug with wet hands!
When not in use, pull out the power plug from the socket.
----Surrounding dust and moisture can age the insulation, and result in a possible leakage fire.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge concerning treadmills,
unless they are being supervised or have been given instructions concerning use of the
appliance by a person responsible for their safety.
Children should be supervised during use to ensure that they do not play with the appliance
and or use it in ways it was not intended for.
Treadmill Grounding Safeguard System
This product must remain on the ground while in use at all times. If you notice the machine
seems to be dysfunctional or unstable, keeping the treadmill on the ground will allow electricity
to flow directly into the ground reducing the risk of electric shock.
This product is equipped with power plug that has a grounding conductor that can auto connect
the treadmill electricity into the ground. Completely insert the plug into a standard socket for
proper use.
If the treadmill’s grounding conductor’s connection is improper, it will cause electric shock. If
you have any doubt about whether your product is grounded correctly or not, please contact a
professional to check and verify for you.
When plugging in the treadmill power cord, please plug it into a socket that has the same shape
as the plug itself. Do not use a plug adapter.
!

5
3. Installation Instructions
When installing, simple arrange all of the screws in their proper position first, then tighten the
screws the treadmill frame has been positioned when the installation of frame is done.
NO.
Name
QTY
1
Complete Machine
1PC
2
6mm inner hexagon wrench
1PC
3
5mm inner hexagon wrench
1PC
4
Combination wrench
1PC
5
Safety key
1PC
6
Silicon oil
1PC
7
MP3 cable
1PC
8
Screw M6*12
4PCS
9
Screw M8*25
2PCS
10
Plum knob(M10*20)
1PC
11
User’s manual
1PC

6
1. Put the machine flat on the ground. Raise the supportive columns and console upward in the direction
shown by the arrows in the picture below.
1. Use a #5 hexagon wrench and screw provided screws (M6*12) to secure the treadmill base (use
two M6*12 screws for each side). Then screw in the preinstalled M8*22 screws underneath as shown
in the left picture below (1 screw on each side).
2. Hold the left and right columns upright, then using a #6 hexagon wrench, screw in the M8*25
screws to secure the console frame to the upright columns. Be sure to tighten any screws installed in
previous steps. Take care to not accidentally clamp the cable between the upright columns.
3. Take the plum knob(M10*20) from the accessory bag. Use this knob to lock the main base and
columns in place by rotating clockwise, please refer to the picture below.
If your treadmill is on an uneven surface, this may cause difficulties when rotating the knob. Please lift
the column slightly forward so the running surface is perfectly flat in mid-air and tighten the knob as
shown in the picture below. In order for the machine to be able to fold easily, please do not twist the
knob too tight.
M6*12
M8*22
M8*25

7
4.Put the safety key on the yellow circle on the console, as seen in the picture below. Press the start
button to start the treadmill. (Notice: The treadmill only starts when the safety key is attached to the
yellow circle on the console.)
NOTE: after you have finished putting the treadmill together, ensure that all screws are installed in
their appropriate place according to the previous steps. Please ensure all parts are properly locked in
and secured by screws before plugging in electricity.
Folding instructions
When the treadmill is not in use, you can lift the running deck and them use knob to lock the running deck
and base, as shown in the picture bellow.
Safety key is in
red color. Please
find it in the
accessory bag.

8
4. Using Instructions
Using your treadmill
1) Insert the power plug properly and turn on the switch(in red color)
When the light is on, you will hear beep sound, and then the screen will light up.
2) Safety key Introduction
The treadmill can only start when the safety key is put on the yellow area of the display console.
Clip the safety key on clothes when using the treadmill to avoid accidents. For emergency conditions,
remove the safety key can stop the treadmill immediately. And put the safety key back to continue
using the treadmill.
3) Console instructions
Start-up: Press Start button to start the treadmill. Normally start after 5 seconds of the countdown.
Programs and modes: There are 12 automatic programs and 3 modes.
Safety lock function: When the safety key is disconnected, “E7” will appear on the screen, the
treadmill will gradually stop and you will hear a beeping sound. When you put the safety key back,
all of the data on the screen will be cleared in 2 seconds. Under whatever circumstance, the
treadmill will stop when disconnected from the safety key and it will immediately show the data
from your run on the screen. Once you put the safety key back, the data on the screen will reset.
1

9
4) Button function
Start button/Stop
When the power is on, press the start button and the screen will display “0.8 km/h”, and the
treadmill will start. When you are running on the treadmill and press the stop button, all of the data
on the screen will clear and the treadmill will gradually come to a complete stop and return to
manual mode. Quick buttons located on the handle grip can also be used to start or stop the
treadmill(left side).
Program
When the treadmill is in standby mode, pressing the program key multiple times can cycle the
options from manual mode to different automatic programs (P1-P12). The default speed while using
manual mode is 0.8 km/hour, the highest speed is 12.0km/hour.
Mode
When the treadmill is in standby mode, press the mode key to cycle through 3 different ways to
countdown your running: time, distance and calories.
Volume ± rotary knob
When connect with mobile phone, rotate the knob clockwise to turn the volume up and rotate
counterclockwise to turn the volume down.
Speed ± key rotary knob
Use these keys to adjust the speed of the treadmill. Rotate clockwise to increase the speed and rotate
counterclockwise to decrease the speed. You can also press the knob to adjust the speed directly by
3.0km/h ,6.0km/h and 9.0km/h.Quick buttons located on the handle grip can also be used to start or stop
the treadmill(left side).
(right side).
5) Display Function
Speed Display
Display the current running speed value.
Time Display
Display the time of manual mode and the countdown time under automatic modes and programs.
Distance display
Display cumulative distance under manual mode and programs. Display the distance countdown in
automatic mode.
Calorie display
Display cumulative calorie under manual mode and programs. Display the calorie countdown in
automatic mode.
Heart rate display
The heart rate value will show on the display when you place your hands on the heart rate monitors.
(The number is for reference only, it cannot be considered as medical data.)

1
7. Automatic program
Each program is divided into 10 segments, and the running time of each segment of the program
is evenly distributed. Following is a form of speed distribution of 12 programs.
Time
Program
Set time/ 10 = Running time of each segment
1
2
3
4
5
6
7
8
9
10
P1
Speed
3
3
6
5
5
4
4
4
4
3
P2
Speed
3
3
4
4
5
5
5
6
6
4
P3
Speed
2
4
6
4
3
4
6
2
3
2
P4
Speed
3
3
5
6
3
6
5
4
3
3
P5
Speed
3
6
6
6
4
3
3
5
5
4
P6
Speed
2
6
5
4
4
3
5
3
3
2
P7
Speed
2
5
5
3
3
6
5
3
2
2
P8
Speed
2
4
4
4
5
6
4
4
6
2
P9
Speed
2
4
5
5
6
5
6
3
3
2
P10
Speed
2
5
3
5
4
6
5
2
4
3
P11
Speed
2
5
6
3
4
5
6
5
3
2
P12
Speed
2
3
5
6
4
6
5
6
5
3

10
Error Code Meaning
Error code
Error Description
Error handling
E1
Disrupted Electronic
Connection: When turned on,
the connection between the
lower controller and the
console is abnormal.
Possible Causes: The electronic connection between the
console and lower controller is blocked, check each
wire that connects the console with the lower controller,
make sure that each wire base is fully plugged in.
Check the cable of the console and lower controller,
replace it if it’s broken.
E2
No motor signal
Possible Causes: The motor cable might not be
connected. Check the connection, connect the cable if
disconnected. The motor might be damaged. Check to
see if it has visible damage or a burnt smell. If yes,
replace the motor.
E5
Electric Current Overload
Prevention: When the treadmill
is running, the controller
detects the electric current is
over 6A(unit to measure
electricity) for more than 3
seconds.
Possible Causes: *Overloading the treadmill machine
system through prolonged use can lead to excessive
electric current and the treadmill will stop for your
safety. *A part might be stuck causing the motor to
stop, adjust the treadmill and restart it. *The motor may
need to be replaced, check if there is a liquid or burnt
smell while the motor is running, if yes replace it. *The
treadmill monitor may need to be replaced, check if it
has a burnt smell, if yes replace the monitor. *The
power supply voltage may need to be changed, check
the power supply voltage if it does not match
specifications adjust to the correct voltage and test the
treadmill again.
E6
Explosion Prevention: An
abnormal voltage level or motor
issue has caused the motor to not
work properly
Possible Causes: The power supply voltage may be low.
Check if the power supply voltage is 50% lower than
the normal voltage of 110V, if it is, adjust it back to
110V and test the treadmill again. *The controller may
need to be replaced. Check if the controller has a burnt
smell, if yes, replace the controller. *The motor cable or
wire may need to be reconnected. Check if the motor
cable and wire are connected, connect if one or both are
not properly connected.
E7
No safety key
Put the safety key back on the yellow circle on the
console.

11
5. Routine Maintenance
Warning: Before cleaning or doing product maintenance, please ensure the treadmill power plug is
pulled out of the electric socket.
Cleaning: Thoroughly cleaning your treadmill will extend its usage life.
Remove dust periodically in order to keep the parts clean. Be sure to clean both sides of running belt,
this will reduce the accumulation of dust and dirt. Treadmill belts must be cleaned with a damp
soapy cloth. Do not use a dripping wet cloth. Please be sure to not wet the electrical components of
the treadmill including underneath the running belt to keep everything dry and functional.
Warning: Ensure that the power plug is disconnected before removing the motor cover. Clean the
motor at least once a year.
Running belt specialized lubricant
This electric treadmill’s running board and running belt have already been lubricated in the
manufacturing process. Friction between the running belt and running board heavily impacts how
long your treadmill will last and its performance, therefore regular application of the lubricant is
needed. Please check the board regularly to ensure it is properly lubricated. If the board’s surface is
damaged, please contact our customer service center. We recommend applying the lubricant
between the running belt and running board using the following schedule:
Light user (uses treadmill less than 3 hours a week): Apply lubrication once a month
Heavy user (uses treadmill more than 7 hours a week): Apply lubrication twice a month, at the
beginning of the month and halfway through the month.
1. For safety measures and to extend the life of your treadmill, it is recommended that if you use the
treadmill for 2 hours or more non-stop, to turn off the machine and let it rest for 10 minutes before
using again.
2. If the treadmill belt is too loose, you will experience skidding while running. If the belt is too
tight, it may reduce motor performance and increase friction between the roller and running belt
impacting your running experience. You can lift two sides of the running belt for 50-75mm when
the tightness is appropriate.
Running with adjusted alignment and tightness
In order to use your treadmill properly so it can function well, it is necessary for you to adjust the
running belt into the best position.
How to align the running belt
Put the treadmill flat on the ground
Make the treadmill run at a speed of about 6-8km/hour
If the running belt is closer to the right, rotate the right adjusting bolt with a ½ turn
clockwise, then rotate the left adjusting bolt with a ½ turn counter-clockwise (PictureB)
If the running belt is closer to the left, rotate the left adjusting bolt with a ½ turn clockwise,
then rotate the right adjusting bolt with a ½ turn counter-clockwise (Picture A).

12
Picture A Picture B
Applying silicone oil
Step 1: Open up the treadmill belt
Step 2: Open the silicone oil bottle, squeeze the silicone oil to both sides of the running board, as in
the picture bellow: