Living Spaces 7030-00170 User manual

MAS90: 5043-43382
SEDONA BRONCO TOPFRAME HARDWARE
QTY: DESCRIPTION:
24 1/4" X 4" LAG BOLTS BLACK
24 3/16" WASHER BLACK
62" CORNER BRACKETS BLACK
10 #6 X 1-1/4" PHIL FLAT PARTICLE BOARD SCREW
24 #8 X 3/4" PHIL PAN TSA ZINC
7030-00170 KIT

4796/4797
7030-00170
BRONCO LOFT TOP
BUNK
PARTS LIST:
A) 24 -4 1/4" Lag Bolts
B) 24 -Black Steel Washers
C) 2 -End Assemblies
D) 2 -5 1/4" x 75" Mattress Rails w/Support Cleats
E) 4 -3 1/4" x 75" Guard Rails
F) 3 -3 1/2" x 38 3/4" Mattress Supports
G) 10-1 1/4" Black Flat Head Wood Screws
H) 6-Angle Brackets
I) 24-3/4" Round Head Screws
J) 2 -Modular Roundup Case Ends (Desk or Chest)
TOOLS REQUIRED:
1) 7/16" Wrench or Socket Wrench
2) Phillips Head Screwdriver
Make you have all parts before beginning assembly. If you need a part, contact Living Spaces.
1)Attach two mattress rails(D) and four guardrails(E) to end assemblies(C) with 24 lag bolts and 24 washers,
and tighten.
2) Place modular case ends(J) as pictured on page 3, with an overall width of approximately 84". Place
completed top bed assembly on the modular ends. There should be about 3" of each modular end top
extending beyond the bed assembly at each end.
3) Attach the bed assembly to the modular ends with the 6 L brackets and 24 round head screws. See diagram
on page 3 for location suggestion.
4) Roll out Slat Kit and stretch from bed end to bed end. Secure with 4 wood screws, in each end of the two
outermost slats, one in each corner of the bed. Center 3 individual slats in the 3 built in gaps of the slat kit,
and secure with 6 wood screws in the ends of each individual slat.
5) Attach ladder to middle rail on top bed assembly (lower guard rail (E))
6) Add mattress not thicker than 10" and sleep well!
Recommended: Electric driver with 7/16” socket
A FOUNDATION IS REQUIRED WITH 3 SLAT CONFIGURATION

1 X 1
BRACKETS 1 X 1
BRACKETS
1 X 1
BRACKET
1 X 1
BRACKET
1 X 1
BRACKET 1 X 1
BRACKET
--------
--------

00500
SAFETY WARNING
Our Bunk Beds have been tested by an Independent Laboratoryand are certified to be in compliance with: ASTM F-1427,
“Standard Consumer Safety Specification for Bunk Beds” and U.S. Government specifications 16 Code of Federal
Regulations, parts 1213 and 1513.
SAFETY WARNINGS
1. Follow the information on the warnings attached to the upper bunk end structure and on the carton. Do not remove this
label.
2. Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood of entrapment or
falls.
3. Surface of mattress must be at least five inches(127mm) below the upper edge of guardrails.
4. Do not allow children less than six years of age to use the upper bunk.
5. Periodically, check and ensure that the guardrail, ladder and other components are in their proper position, free from
damage and that all connectors are tight.
6. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
7. Prohibit more than one person on upper bunk.
8. Always use the ladder or bed end for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact manufacturer or dealer for replacement parts.
10. Use of a night-light may provide added safety precautions for a child using the upper bunk.
11. If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed should be placed against the
wall to prevent entrapment between the bed and the wall. (This applies only to bunk beds without two full-length
guardrails.)
12. Always use guardrails on both long sides of the upper bunk.
13. The use of water or sleep flotation mattress is prohibited.
14. Keep these instructions for future reference.
STRANGULATION HAZARD
15. Never attach or hang items to any part of the bunk bed that are not designed for use with the bed for example, but not
limited to hooks, belts and jump ropes.
SIZE OF MATTRESS AND FOUNDATION
Your Twin bed is designed to use a mattress 37”-39” in width and 74” - 75” in length.
Your Full bed is designed to use a mattress 52”- 54” in width and 74” - 75” in length.
The total thickness of mattress and foundation (slat kit, bunk board, etc.) combined must not exceed 10”. Note: There must
be at least 5” from mattress sleeping surface to top edge of guardrail.
REPLACEMENT PARTS
Replacement parts, including additional guardrails, maybe obtained from your Furniture dealer.
4137, 4145, 4151, 4175, 4270, 4738, 4797
4516,4517,4519, 4521, 4523, 4525, 4529 UPDATED: 04/19/2013
A FOUNDATION IS REQUIRED WITH 3 SLAT CONFIGURATION

Installation of individual slats for use with Slat Roll (Slat roll sold separately) See your retailer for purchase of Slat Roll
SCREW
SCREW
SCREW
SCREW SCREW SCREW SCREW
SCREW
SCREW
SCREW
INDIVIDUAL SLATS INDIVIDUAL SLATS INDIVIDUAL SLATS
Installation of individual slats for use with Bunkie Board (Bunkie Board sold separately) See your retailer for purchase of Bunkie Board
SCREWSSCREWSSCREWSSCREWSSCREWSSCREWS
INDIVIDUAL SLATS INDIVIDUAL SLATS INDIVIDUAL SLATS
When used with a slat roll, the three
individual slats should be placed evenly in the gaps and underneath the strapping before fastening.
Individual Slat
Individual Slat
Individual Slat