Living Spaces Sedona 7030-01250 KIT User manual

Sedona Collection: High Sierra Bunk
PARTS LIST
BOX 1: 4721 High Sierra Bunk Ends
Part # Description Quantity
S1010END High Sierra Bottom Bunk End 2
S1011END High Sierra Top Bunk Left End 1
BOX 2: 4720 High Sierra Frame Rails
Part # Description Quantity
S1002SRL 5/4x8 Mattress Rail 4
560750001 5/4x6 Guard Rail
2
149383/40 Individual Twin Slat 3
140533/40 Individual Full Slat 3
FLDWL 3" Fluted Dowel 4
5040-43181 Hex Lag Bolt/Washer 24
Picture
Picture
For: 4720 Frame Rails/4721 Bunk Ends
7030-01250 KIT
S1012END High Sierra Top Bunk Right End 1
5040-35410 #6 x 1 1/4" Phil Flat Slat Screw 20
COMPLETED ASSEMBLY

1) Attach two mattress rails (S1002SRL) to two bottom end assemblies (S1010END) with 8 lag bolts
and 8 washers (5040-43181), and tighten.
2) Attach two mattress rails (S1002SRL) and two guard rails (560750001) to left top end assembly
(S1011END) and right top end assembly (S1012END) with 16 lag bolts and 16 washers (5040-43181),
and tighten.
3) Place four wooden dowels (FLDWL) in the four holes in top edge of bottom bunk assembly.
4) Place the top bunk assembly on the bottom bunk assembly, ensuring that the dowels are inserted in
holes in the top bunk assembly.
5) Place slat kit (purchased separately) and 3 individual slats (140533/40) in accordance with the
diagram on the last page of these instructions. Attach the 5 designated slats to the mattress rail cleats
using the #6x1 ¼” screws (5040-35410).
560750001
5040-43181
S1002SRL
FLDWL S10111END
S1012END
S1010END

00700
SAFETY WARNING
Our Bunk Beds have been tested by an Independent Laboratory and are certified to be in compliance with:
ASTM F-1427, “Standard Consumer Safety Specification for Bunk Beds” and U.S. Government
specifications 16 Code of Federal Regulations, parts 1213 and 1513.
SAFETY WARNINGS
1. Follow the information on the warnings attached to the upper bunk end structure and on the carton. Do
not remove this label.
2. Always use the recommended size mattress or mattress support, or both, to help prevent the
likelihood of entrapment or falls.
3. Surface of mattress must be at least five inches(127mm) below the upper edge of guardrails.
4. Do not allow children less than six years of age to use the upper bunk.
5. Periodically, check and ensure that the guardrail, ladder and other components are in their proper
position, free from damage and that all connectors are tight.
6. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
7. Prohibit more than one person on upper bunk.
8. Always use the ladder or bed end for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact manufacturer or dealer for replacement parts.
10. Use of a night-light may provide added safety precautions for a child using the upper bunk.
11. If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed should be
placed against the wall to prevent entrapment between the bed and the wall. (This applies only to bunk
beds without two full-length guardrails.)
12. Always use guardrails on both long sides of the upper bunk.
13. The use of water or sleep flotation mattress is prohibited.
14. Keep these instructions for future reference.
STRANGULATION HAZARD
15. Never attach or hang items to any part of the bunk bed that are not designed for use with the bed for
example, but not limited to hooks, belts and jump ropes.
SIZE OF UPPER AND LOWER MATTRESS AND FOUNDATION
Your Twin bed is designed to use a mattress 37”-39” in width and 74” - 75” in length.
Your Full bed is designed to use a mattress 52”-54” in width and 74” - 75” in length.
The total thickness of mattress and foundation (slat kit, bunk board, etc.) combined must not exceed 7”.
Note: There must be at least 5” from mattress sleeping surface to top edge of guardrail.
REPLACEMENT PARTS
Replacement parts, including additional guardrails, maybe obtained from your Furniture dealer.
4706, 4711, 4721, 4731, 4738, 4743UPDATED: 06/08/2016
* A FOUNDATION IS REQUIRED WITH 3 SLAT CONFIGURATION *

Installation of individual slats for use with Slat Roll (Slat roll sold separately) See your retailer for purchase of Slat Roll
SCREW
SCREW
SCREW
SCREW SCREW SCREW SCREW
SCREW
SCREW
SCREW
INDIVIDUAL SLATS INDIVIDUAL SLATS INDIVIDUAL SLATS
Installation of individual slats for use with Bunkie Board (Bunkie Board sold separately) See your retailer for purchase of Bunkie Board
SCREWSSCREWSSCREWSSCREWSSCREWSSCREWS
INDIVIDUAL SLATS INDIVIDUAL SLATS INDIVIDUAL SLATS
When used with a slat roll, the three
individual slats should be placed evenly in the gaps and underneath the strapping before fastening.
Individual Slat
Individual Slat
Individual Slat
Diagram 1 Diagram 2
Scan Code for Instructional video

STAIRWAY /BUNK 7030-00420
STAIRWAY CHEST WITH BUNK BED
 

 

 


 
 

 
4453 / 4493 / 4676
 N  N  30  M  N 

THE DRAWERS OF YOU STAIRWAY CHEST HAVE BEEN SECURED FOR
SHIPPING WITH SECURITY STRIPS. TO RELEASE THESE STRIPS PULL EACH
DRAWER FIRMLY OUT UNTIL YOU FEEL THE STRIP RELEASE. EACH DRAWER
WILL FUNCTION PROPERLY AFTER THE FIRST TIME YOU PULL THEM OUT.
THERE IS NO NEED TO ATTEMPT TO REMOVE THE SAFETY STRIPS AS THEY
WILL NOT INTERFER WITH THE PROPER USE OF EACH DRAWER.
4453 / 4493 / 4676 STAIRWAY CHEST
4493
Sedona
Jr. Stairway Chest
4453
Sedona
Stairway Chest
4676
Summit
Stairway Chest

Sedona Collection: Knob Installation
7030-01195 KIT
1. Locate the box containing your knobs in the bottom drawer of your case good.
2. Identify which of the screw sizes is correct for your drawers/doors. The screw should
protrude no more than 1/4" when pushed through the pre-drilled holes on your
drawers/doors.
3. Push the screw through the back of the pre-drilled hole on the drawer/door and line it
up with the thread on the back of the knob.
4. Tighten the screw into the back of the knob until the knob is tight against the front of
your drawer/door.
**You can tighten your screws with either a phillips screwrdiver,
a drill with a phillips bit, or your hand**
(Scan code for
instructional
video)