LLI LLI-C-CTRL-RGBW-HH User manual

847-412-4880 // [email protected] // 1555 Barclay Blvd. Buffalo Grove, IL 60089
INSTALLATION INSTRUCTIONS
HAND HELD RGB(W) CONTROLLER
LLI-C-CTRL-RGBW-HH
**DANGER: Prior to installation, disconnect power at the source.**
Make sure you have all components listed below:
• LED tape
• Connectors
• Extrusion/Lens
• Controls
• Non-dimming power supply
Page 1

Please read all steps before beginning the installation.
847-412-4880 // [email protected] // 1555 Barclay Blvd. Buffalo Grove, IL 60089
INSTALLATION INSTRUCTIONS
HAND HELD RGB(W) CONTROLLER
• WARNING: These products may represent a potential shock or re hazard if improperly installed or
attached in any way. Products should be installed in accordance with these instructions, local electrical codes
and the National Electric Code (NEC).
• Use only with 12V or 24V non-dimmable hardwire power supply. Factory warranty will be void if used
otherwise.
• Do not use if there is any damage to the unit or to the wiring/insulation. Inspect periodically.
• Ensure wires are in complance with local electrical codes.
• Nexus Pro Controllers are intended for indoor use in dry locations and not suitable for outdoor applications.
• Ensure proper gauge wires are installed between power supplies, controls and LED lighting to avoid voltage
drop.
• Ambient temperature should not exceed 110°F or 50°C.
• Recommended load is 80% for optimal performance and lifespan.
Page 2

847-412-4880 // [email protected] // 1555 Barclay Blvd. Buffalo Grove, IL 60089847-412-4880 // [email protected] // 1555 Barclay Blvd. Buffalo Grove, IL 60089
INSTALLATION INSTRUCTIONS
HAND HELD RGB(W) CONTROLLER
Page 3
Indicator: indates the state
of remote control
Color wheel
Hold to dim up all RGB
RGB mixed white: cw, nw, ww
Click to play / pause the 10
built-in effects, Hold to turn
up/down the speed of the
effect
4 zones, click to choose zone,
hold to turn off/on that zone
White channel: the 4th channel
Click to turn on/off, hold to dim
up/down W channel
Hold to dim down all RGB
Hold to save the color/effect
Click to call up the saved
color/effect
ON/OFF of all zones
NOTE: This remote controls 4 zones/receivers.
Each receiver can be paired with a maximum of 8 controllers.

847-412-4880 // [email protected] // 1555 Barclay Blvd. Buffalo Grove, IL 60089
INSTALLATION INSTRUCTIONS
HAND HELD RGBW CONTROLLER
Page 4
Insert (3) AAA batteries into battery
compartment and turn power on to your
remote controller.
Once your controller is powered up,
momentarily depress and release the learning
key on the RF receiver.
NOTE: Repeat steps 2 & 3 for setting other zones/receivers as required.
NOTE:To delete a pairing press and hold the learning key for 3 seconds or until the LEDs
blink twice.
STEP 1
STEP 3
STEP 2
STEP 4
HAND HELD CONTROLLER: Pairing Controller with Receiver
Select the desired zone on your controller 1 /
2 / 3 / 4 and then rotate your nger around
the control wheel until the LEDs respond to
your control.
To save a desired setting on the controller
press and hold S1 / S2 / S3 button until the
indicator light ashes twice.

TYPICAL COLOR CHANGING CONNECTION DIAGRAM
INSTALLATION INSTRUCTIONS
HAND HELD RGBW CONTROLLER
847-412-4880 // [email protected] // 1555 Barclay Blvd. Buffalo Grove, IL 60089
Page 5
120VAC
REMOTE
CONTROL
CONTROL
RECEIVER
POWER SUPPLY
RGB(W) LED TAPE