LLOYTRON MIP SYSTEM 3 B7835 User manual

OPERATING INSTRUCTIONS
MODEL: B7835
Motion Sensor
Transmitter

2www.lloytronhelpdesk.com
• Operating Voltage: 4.5v DC
• PIR Motion Sensor Module requires: 3x AAA 1.5v alkaline batteries
• We recommend Duracell batteries. Do not use Carbon Zinc or Rechargeable batteries.
• PIR Range: 5m (approx.)
• PIR Angle: 110º Horizontal, 45º Vertical
• PIR Sensor is IP44 rated, splashproof
• Operating Frequency: 433.33Mhz
thank you
Thank you for the purchase of this quality LLOYTRON MIP SYSTEM 3™ product. Used carefully and in accordance
with the instructions enclosed, it should give you trouble free performance over a long period of time. Please retain
these instructions for future reference.
FEATURES
SPECIFICATIONS
• Battery Operated
• 175m wireless range
CONTENTS
Features Page 2
Specications    Page2
Out of Box Page 3
Important Safeguards and Precautions Page 3
Wireless Distance Page 4
What is the MIP SystemTM? Page 4
Linkable Solution Page 4
The Generation Gap Page 5
How do I know what Generation I have? Page 5
Link / Programme Devices Page 6
Installing the PIR Motion Sensor Page 7
Different tune different bell push Page 8
Trouble Shooting Page 10
Cleaning and Care Page 11
Weee/Environmental Protection Page 11
MIP Accessories Page 12
Customer Service Page 12

3
www.lloytronhelpdesk.com
OUT OF BOX
Inside this box;
1x PIR Motion Sensor Transmitter
Screws and Stick Pad
1x Operating Manual
You will be required to Link/Programme this sensor to your other MIP System™ Chime Units.
See section on Link / Programme devices
IMPORTANT SAFEGUARDS AND PRECAUTIONS
SAVE THESE INSTRUCTIONS
• Read all instructions carefully
• For Household use only
• The Motion Sensor is splashproof and can be used outdoors but should be protected or covered from large deluge
of water.
• To prevent against the risk of electric shock, do not submerge and part of this appliance in water.
• This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction concerning use of this product,
by a person responsible for their safety.
• Children should be supervised to ensure they do not play with this appliance.
• Cleaning and user maintenance should not be made by children.
• Never let children push anything into holes or slots in the cabinet – this could result in an electric shock.
•Shouldyoundtherangesensitivityorqualityofsounddeteriorating,replaceoldbatterieswithnewonesassoon
as possible. The use of long life Alkaline batteries is recommended.
• Dispose of old batteries carefully and in accordance with local government guidelines.
DO NOT
• Do not use a receiver outside or in damp conditions
• Do not use rechargeable batteries
• Do not mix old and new batteries or different chemistry of batteries.
• Do not use for any purposes other than the intended use.
• Do not use if damaged in any way.
• Do not dismantle. There are no serviceable parts.

4www.lloytronhelpdesk.com
WIRELESS DISTANCE
This wireless Door Chime has an unobstructed operating distance of 200 meters, but local conditions and the
number of walls, doors and material affect this. Metal door frames and other factors may interfere with the signal
and reduce the operating distance
To extend this distance, we suggest using the Signal Booster accessory.
WHAT IS THE MIP SYSTEM™?
The MIP System™ is a wireless audible alert solution with the ability to link additional devices (transmitters, receivers
and sensors) to create the perfect combination for your home or business. Create your bespoke alert solution with
the MIP System™.
LINKABLE SOLUTION
The MIP System™ provides the solution for many scenarios at home or in a business environment. By linking
devices (transmitters, receivers and sensors) it is easy to create a tailor made alert solution, solving common
problems such as:
• Need an extra bell push for the back door.
• A portable receiver for the garden party.
• PIR motion sensor on the driveway.
• Wired module to make my old wired system into a wireless version.
• Magnetic sensor on the shed door.
• Wired module so I can continue using my original ornate bell push.
Additional accessories are shown on the back page of this manual.
200

5
www.lloytronhelpdesk.com
HOW DO I KNOW WHAT GENERATION I HAVE?
On the rear or side of every product is a Rating Plate as shown.
This Rating Plate will advise a batch number, and/or it will state MIP System 2™ or MIP System 3™.
Products prior to batch 24305 are not compatible with MIP System™.
1st Generation MIP is Batch numbers 24305 to 31838
2nd Generation MIP (MIP System 2™) is Batch numbers 31839 to 33178
3rd Generation MIP (MIP System 3™) is Batch numbers from 33179+
THE GENERATION GAP
The new MIP System 3™ is the third generation and is compatible with all previous generations, wherever you see
these symbols.
The 3rd generation has evolved and offers much more than the previous generation:
• Choose 4 consecutive tunes for different bell pushes or transmitters*
• Longer wireless unobstructed range of 200m for mains operated chime units, 175m for battery operated
chime units
• High quality UK customised true sounds
• Ability to link over 16 different devices
Note: * consecutive tune selection is not available for Original MIP, which will only select the default sound on the
Chime Unit.
Additional accessories are shown on the back page of this manual.

6www.lloytronhelpdesk.com
1. On each chime unit, press and
hold the chime selection button
or chime replay button for 10
seconds. An audible beep beep will
be heard. The chime unit is now in a
waiting mode for 15 seconds to link
the transmitter.
LINK / PROGRAMME DEVICES
You will be required to link/programme this new accessory to your existing MIP System™. It is advisable to link
before you mount the Motion Sensor Module.
Note: for easy programming, keep the Motion Sensor Transmitter and chime unit close together whilst linking/
programming. This saves time and effort.
2. Using the switch at the rear of
the unit after the batteries has been
installed. Move the switch to the
ON position and an audible BEEP
will be heard again to advise the
Sensor transmitter has been linked
successfully.
If multiple receivers are being used, then each receiver must be programmed to the corresponding bell push
individually.
Also refer to individual device manual for accessories before linking.
BEEP
BEEP
BEEP
4. SWITCH the Sensor OFF and
then back ON to trigger the Chime
Unit sound.
BEEP
BEEP
3. To exit programming mode, press
the chime replay button again or
wait several seconds until a beep
beep is heard. The link process has
now completed.

7
www.lloytronhelpdesk.com
INSTALLING PIR MOTION SENSOR MODULE
The PIR Motion Sensor module is ideal for sheds, garages and hallways etc. It will activate any linked door chime
receiver every time it detects movement within a 5m range. The unit is splashproof and is suitable for use outside.
Please note that birds, pets and other animals may also trigger the device.
• Pry open the battery compartment at the back of the sensor.
• Insert 3x AAA batteries observing the correct polarity as indicated on the sensor and the battery.
• If required, change the red switch settings as described in “Different Bell Push Different Tunes”. If unsure, leave
on default setting.
• If mounting with screws, screw through the holes provided.
• Ifnotmountingwithscrews,usetheself-adhesivepadsuppliedandafxsothePIRSensorispointingtowards
the area required to monitor.
WARNING: DO NOT PLACE IN DIRECT SUNLIGHT. This may cause premature activations.

8www.lloytronhelpdesk.com
DIFFERENT TUNE DIFFERENT BELL PUSH
InsideallMIPSystem3™transmitters(includingbellpushes,sensorsandmodules)youwillndaseriesofswitches
which allow you to choose one of four consecutive sounds on any compatible chime unit so you can identify which
transmitter has been triggered.
You can have up to four chime sounds play on different transmitters, but please note, these chime sounds cannot
be chosen at random. Once the default chime sound has been chosen on the chime unit, the next three consecutive
sounds in the order they occur on the chime unit can be selected.
Inside the bell push or transmitter casing you will see a red block with two micro switches.
Change setting as shown below:
DEFAULT SETTING
This default setting is compatible with ALL generations of MIP SystemTM Door Chimes.
1ST CHIME SOUND
Selecting the default setting on a transmitter will play the default sound chosen on the paired chime
unit.
WARNING
If you are not looking to pair the device with an additional transmitter, or do not want different sounds for different
transmitters, please leave transmitter(s) in the default setting.
ADJUSTABLE SETTING
Using these settings will only work with MIP System 2TM or MIP System 3TM products. Please check compatibility
before use or leave on the default setting.
The sound chosen on the paired chime unit will play when the default setting is in place, to select up to the next three
consecutive sounds on the chime unit you will need to move the micro switch to the positions as instructed below.
2ND CHIME SOUND
Position the micro switch as shown in the diagram to set the transmitter to play the 2nd chime sound
on the paired chime unit.
3RD CHIME SOUND
Position the micro switch as shown in the diagram to set the transmitter to play the 3nd chime sound
on the paired chime unit.

9
www.lloytronhelpdesk.com
4TH CHIME SOUND
Position the micro switch as shown in the diagram to set the transmitter to play the 4nd chime sound
on the paired chime unit.
If not compatible, then leave on Default setting otherwise no activation will be made and it will not sound on the
chime unit.
See section ‘How do I know what generation I have?’
WARNING
ThesesettingsareNOTcompatiblewithnon-MIPproductsorrstgenerationMIPSystem™1,butarecompatible
with the Second generation MIP System 2™and Third generation MIP System3™ Door Chimes.

10 www.lloytronhelpdesk.com
TROUBLE SHOOTING
QUERY SOLUTION
No blue light on the bell push when pressed Check the battery is inserted is correct polarity and
is not dead.
No Sound when bell push is pressed, bell push
illuminates, and Tune sounds when I press Chime
Replay on Chime Unit
Check that switch settings inside the bell push are
on default.
Try to re-link the bell push to the receiver by following
the section on link/programme devices.
No Sound when bell push is pressed, bell push illu-
minates, and NO Tune sounds when I press Chime
Selection on Chime Unit
Ensure mains switch is plugged in and switched on
at the wall.
Chime unit is activating every few minutes. Check the sensor has not been broken or is sticking
or there is water inside the unit
For further assistance and troubleshooting or on the range of MIP System™ products visit
www.doorbellsolutions.com or contact customer services.