Lmppos KS-380 series User manual

User’s Manual
KS-380 Series
Safety warning
Safety notice
Only the supplied AC power adapter and lithium battery is allowed
to use, otherwise it may cause device damage, battery leakage, fire,
and even explosion.
Do not put the battery into a fire or apply direct heat to it or
disassemble it, otherwise cause the battery leakage, fire, and even
explosion.
Please remove the battery from the printer and store separately if
the printer will not be used for a long period of time, otherwise cause
the battery leakage.
As the battery’s liquid is corrosive, if there any case of operational
mistakes to cause leakage, please wash immediately with plenty of
clean water if skin or clothes contact it carelessly. If entering eyes,
wash with plenty of clean water at once and seek medical advice.
Do not touch the paper tear-off knife.
The print head is a heated part, please do not touch the print head
and other parts around it during or after the printing process.
Do not touch the print head and plug-in parts to avoid print head
damage.
Do not open the top cover when printing, otherwise may cause
printer work failure.
In order to get good print quality, and extend the device service life,
we suggest that using the recommended thermal paper roll or which
is the same quality of.
Do not print when it’s out of paper, which will seriously damage the
print head and rubber roller.
Make sure printer power is turned off when connecting and
disconnecting the power cable or data cable.
Do not let water or conducting material (eg. Metal) into the printer,
please turn off the power immediately if happened.
Please make sure to charge the battery for 60% or above and then
remove the battery from the printer and store separately if the printer
will not be used for a long period of time.
Please keep this manual for your reference.
Paper roll diameter: 50±0.5mm
Two kinds of Interface optional: USB+Bluetooth (standard ),
USB+WIFI (optional)
Standby time: m
USB+Bluetooth: BT3.0 and BLE4.0, support Android and iOS system.
USB+WIFI: AP/STA/AP+STA mode to set up the networks.
Support USB virtual COM port for developing and testing by developer.
Compatible with ESC/POS printing commands, support NV logo
download printing, various 1D bar code and QR code.
Low power consumption, good print quality, 50km mechanism lifespan.
Support GB18030 Simplified Chinese, Big5 traditional Chinese,
Korean, international character set and extended code pages.
LED can be showed abnormal condition of the printer, battery capacity
status, charging and connection status ect.
Freely offer DLL, SDK, Demo for developing.
ore than 36 hours for more than
for BT mode.
Wifi mode, 96 hours
Main Features:
After unpacking the unit, please check that all the necessary
accessories are included in the package.
Unpacking
1pcs
1pcs
1pcs
1pcs
1pcs
User’s manual
Printer
Lithium battery
USB cable
Power adapter
Technique Spec
Printing
Barcode &
Character
Buffer
Physical
Properties
Power
Environment
Reliability
Print method
Print width
Paper diameter
Paper thickness
Paper width
Print speed
Paper cutting way
Dot density
Interface
Print commands
Fonts
Character size
Fonts
Barcode
Code page
Data
NV Flash
Dimension
Weight
Power adapter
Lithium battery
Charge period
Work
Environment
Storage
Environment
Mechanism
Direct thermal line
80mm
50±0.5mm
0.06~0.08mm
72mm (Max)
60mm/s (max)
Tear-off
576dot/line
USB+Bluetooth3.0/BLE4.0 (Standard)
USB+WIFI (Optional)
Compatible with ESC/POS
ANK Font: Font A: 12*24dots
Font B: 9*17dots
Simplified/Traditional Chinese Character,
Korean: 24*24dots
GB18030, Big5, Korean
UPC-A/UPC-E/EAN(JAN)13/EAN(JAN)8/
CODE39/CODABAR/ITF/CODE93/
CODE128/QR code
PC437/Katakana/PC850/PC860/PC863/
PC865/West Europe/Greek/Hebrew/
East Europe/Iran/WPC1252/PC866/PC852/
PC858/IranII/Latvian/Arabic/PT151,1251/
PC747/WPC1257/Vietnam/PC864/PC1001/
Uygur/Thai
4K bytes
60K bytes
131*107*58mm
430g (including battery)
Input: AC220V output: DC 9V/1A
2200mAh/7.4V
3h-5h
Temperature: 0～45℃, Humidity: 10～90%
Temperature: 0～50℃, Humidity: 10～90%
50km

Printer parts:
1.
2.Power button
3.Function key button
4.Power port
5.Status indicator (Blue)
Feed button
Paper Roll Installation
a.Open the cover. b.install
the paper roll.
Correctly
Battery Installation
1. Open the cover. 2. Insert the left side to install the
battery at the rear of the printer,
push the right side of the battery.
3. Close the cover.
Battery Charging
Indicators, Beeper and Buttons:
NOTE:
1. Charging the battery must be in the state of power-on.
Printer
Input: AC100-220V
Output: DC9V/1A
6.Battery status indicator (Green)
7.Error indicator (Red)
8.USB port
9.Cover open button
Status
ERROR
indicator
(Red)
Battery
status
indicator
(Green)
STATUS
indicator
(Blue)
Beeper
OFF
Blinking
Blinking
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
Blinking
OFF
OFF
OFF
ON
OFF
OFF
No
Yes
No
No
No
Yes
Printer power off.
Printer power on, but out
of paper.
printer overheated
protection is activated.
Bluetooth/WiFi connected.
Long press the power button for 3 seconds.
Note:The printer can not be printed without using battery.
Printer power ON/OFF.
Pr e s s t h e PO W E R b u t to n a nd F U NC
b u t t o n s i m u l t a n e o u s l y, w a i t f o r t h e
green lights light in turn, then release the
POWER button firstly. the red light and blue
light lights up in turn, after the blue light
di m s , re l e a se t h e FU N C b ut t o n ; r e d
light dims, the printer motor will vibrate.
Printer initialization
Printer power on, press the FEED button. Paper feed
Hexadecimal Dumping
Press the FEED b utton and the POWER
bu t t o n s i m u l t an e o u sl y, w a i t fo r a l l t h e
lights are bright, then release the POWER
button firstly, wait for STATUS indicator
(blue light) dims, then release the FEED button.
Print Self-test page
Press the FEED button and the POWER
button simultaneously, wait for all the
lights are bright, then release the POWER
bu tt o n f ir s t l y ; af t e r th e b l u e li g h t
and red light dims in turn, then release the
FEED button , meanwhile the p rinter
prints out "Hexadecimal Dump" page, then
printer is changed to Dump mode.
Interface informationPrinter power on, press the FUNC button.
c.Close the top cover, keep
5mm of the paper outside.
Connect printer with computer via USB cable, and then turn on
the printer power, a U-Disk appears in computer, which saved
the driver software into a zipped package. Please copy to your
local disk for driver installation.
Driver software
Troubleshooting
Problem Possible Cause Recovery Procedure
*
dirty.
The print head sensor is * Please use soft brush to
clean the sensor.
The following guide lists the most common problems that may
be encountered when operating this printer. If the printer still
does not function after all suggested solutions have been
invoked, please contact the Customer Service Department of
your purchased reseller or distributor for assistance.
Printer doesn’t
power on.
* The battery is used up. * Please use the original
AC power adapter to
recharge it and start
again.
Poor print quality * Poor media quality.
* The print head is dirty.
* The platen roller is dirty.
* Change proper media roll.
* Please use the lint-free
cloth with 100% ethanol
to wipe the print head and
the platen roller.
⑨
Printer doesn't
detect the paper.
Low battery.
Printer is powered on and
in normal print mode.
Battery charging process.
The green lights flash from left to right
in turn.