Lockrack Extendable User manual

INSTRUCTIONS
PARTS INCLUDED
1. (8X) T-NUT & PLASTIC SPACER
2. (4X) LOCKRACK BASE
3. LOCKING MECHANISM
4. (8X) NUT ATTACHING BASE TO T-BOLT
5. RUBBER BASE PROTECTORS
6. (4X) LOCKRACK ARM
7. SPACE BAR
8. (8X) ADAPTORS
9. TOOLS
LOAD BAR SET UP
INSERT SPACE BAR
INTO BASES. SELECT
THEDESIREDDISTANCE
YOU REQUIRE FOR YOUR
W ATERCR AFT . ALIGN WITH
T BOLT, PLACE THROUGH
BOTH BASES AND SPACE
BAR..
LOAD BARS MUST BE
POSITIONED AT LEAST
24” OR MORE APART TO
ENSURE S T ABILITY .
ATTACH LOCKRACK BASES TO LOAD BARS
IF THE LOAD BARS ARE
EQUIPPED WITH ACCESSORY
GROOVES SLIDE THE
T BOLT HARDWARE WITH THE
BLACK RING INTO THE LOAD
BAR GROOVE. IF THE LOAD
BARS DO NOTHAVE GROOVES,
THEN USE THE ADAPTER
INS TRUC TIONS BEL O W .
SLIDE THE T BOLT TO ALIGN
WITH THE SCREW HOLES IN
THE BASE.
BEFORE MOUNTING THE
BASE ONTO THE LOAD
BAR, PULL THE RUBBER
PROTECTOR FROM THE
BASE.
1. ONCE THE BASE IS PROPERLY
POSITIONED ON LOAD BAR,
TIGHTEN THE BOLTS WITH A
10MM WRENCH.
2. AFTER THE BASE IS TIGHTENED
COMPLETELY TO THE LOAD
BAR, REPLACE THE RUBBER
PROTECTORS WHILE ALIGNING
THE PRE-FORMED HOLE WITH
THE BOLT.
TOOLS NEEDED FOR INSTALLATION (INCLUDED)

LOADING WATERCRAFT
PROPERLY POSITION THE
WATER CRAFT (E.G. PADDLE
BOARD, KAYAK, ETC.) ON TOP
OF THE BASE. IN MOST CASES,
THE WATER CRAFT WILL BE
UPSIDE DOWN (SUP FINS
UP AND FORWARD, SURFSKI
WITH HULL UP). SLIDE THE
ARMS INTO THE BASE UNTIL
THEY CONTACT THE WATER
CRAFT ON BOTH SIDES.
AFTER ALL 4 ARMS ARE IN
LOCKED POSITION AND TIGHT
GIVE THE BOARD A WIGGLE
TO MAKE SURE IT IS SECURE.
IF THERE IS ANY MOVEMENT,
YOU MUST ADJUST THE WATER
CRAFT TO PROPERLY ALIGN THE
ARMS WITH THE GROOVES ON
THE BASE.
UNLOADING WATER CRAFT
TO REMOVE THE WATER
CRAFT, START WITH THE KEY
POINTING DOWN LIKE IMAGE
BEL O W . TURN THE KEY T O
THE RIGHT TO RELEASE THE
RATCHET AND PULL OUT
THE ARM.
WHEN NOT IN USE THE ARMS
CAN BE PLACED DOWN FOR
MORE STREAMLINE AESTHETIC.
DOWN TO THE LEFT IS LOCKED
AND WILL NOT BE ABLE TO
COME OUT, DOWN TO THE
RIGHT THE ARM IS NOT IN A
LOCKED POSITION AND CAN
EASILY COME OUT OF ITS
GROOVE. HOLE FACING LOCK
SIDE, LOCKS ARM INTO PLACE
(SEE TOP IMAGE).
ADAPTER INSTRUCTIONS
LOOSEN THE BOLT WITH A
SIZE5MMOR 3/16”HEXKEY.
ADD THE BLACK RING ON
TOP OF THE SCREW AND
ADAPTER. ATTACH THE
ADAPTER TO THE LOAD
BAR AND TIGHTEN WITH
HEX KEY FULLY, WITH NO
MOVEMENT.
ONCE LOOSENED PULL DOWN
THE RUBBER PAD ABOVE
BELOW THE SCREW HOLE TO
REVEAL THE RECTANGLE AND
GROVE FOR THE T BOLT.
ATTACH THE ADAPTOR TO THE
LOAD BAR, WITHOUT MAKING
IT COMPLETELY TIGHT UNTIL
YOU HAVE ALIGNED THE
SCREW HOLES WITH THE BASE.
ONCE IN DESIRED LOCATION
OF THE LOAD BAR, TIGHTEN
COMPLETELY, WITH NO
MOVEMENT AND PROCEED TO
TIGHTENING OF THE BOLTS ON
THE LOAD BAR. CAREFUL NOT
T O O VER TIGHTEN AND S TRIP .