Locus Solutions GO Real-Time 3G User manual

Confidential Preliminary-Subject to Change
User manual
Model Name: GO Real-Time 2G/3G
By
Locus Solutions
05 ,22, 2017
Revision History
Revisio
n
Date
Descriptio
n
X1.00
18/10/04
Initial Release
2013 Locus Solutions Page 1 of 6

Confidential
Preliminary-Subject to Change
2013 Locus Solutions Page 2 of 6
Scope
This document is a user manual for the GO Real-Time 2G/3G monitoring temperature device.
Description
The GO Real-Time 2G/3G is a self integrated commercial grade monitoring temperature device that
uses in the cold storages.GO Real-Time 2G/3G is optimized for reliability, cost and size.
All antenna including GSM/WCDMA antenna are internal to the device. Data reporting can be
initiated by a command center or by the device itself via GSM/GPRS/WCDMA, SMS or PDP
pathways.
The GO Real-Time 2G/3G is unique in that it is intrinsically expandable. A fastened
expansion door secures SIM card access.
The GO Real-Time 2G/3G has a embedded lithium battery, the battery has 5400mAh capacity .
The GO Real-Time 2G/3G is based on chip level design. The application software executes on the
base level Central Processing Unit (CPU) under direct Operating System (OS) control.This approach
provides a much more reliable, lower power and faster response than module/processor architectures.
Unlike in common module/processor based designs; the GO Real-Time 2G/3G design allows direct
operating system access by the application, thus mitigating the need for a redundant external
processor.
For added monitoring temperature application ,a temperature sensor IC oversees the GO Real-Time
2G/3G system operation.
The GO Real-Time 2G/3G Device can be provisioned for UDP and SMS data services for
both application command and data transactions within the 850 & 1900 or 900 & 1800
MHz GSM bands and Band1&Band2&Band5&Band6&Band8 WCDMA band.Network
provisioning is done with standard SIM cards.
A USB Port that is compliant with Version 2.0 of the USB
standard for high speed operation is provided for upgrade/download the program.
The power input, ground that are provided by the internal lithium battery that supports connection
of a rechargeable battery.
Over The Air (OTA) application firmware updates are supported through at TFTP connection to a
server. The entire image can be updated using one simple command. This includes transient
electrical noise and Electro Static Discharge (ESD).
The GO Real-Time 2G/3G is a small Blue - white box with unremarkable features. Two LED
status indicators
are provided to verify correct installation and initial operation. A unique power management feature
allows these LEDs to be extinguished once installation is verified to be correct. This feature
reduces power.
As with all monitoring temperature device , the GO Real-Time 2G/3G should be used in a Cold
storages that it is a enclosed space . Double sided foam tape can be used to secure the surface not
facing the sky if needed.
Physical Attributes
Figure 1 shows various views of the GO Real-Time 2G/3G Device and its critical physical features.

Confidential
Preliminary-Subject to Change
2013 Locus Solutions Page 3 of 6
Figure 1
GO Real-Time 2G/3G Physial
Attributes

Confidential
Preliminary-Subject to Change
2013 Locus Solutions Page 4 of 6
CE Regulations:
Caution
Risk of explosion if battery replaced aced by an incorrect type.
Dispose of used batteries according to the instructions.
Please make sure the temperature for device will be from -10˚C to 45˚C .
The manufacturer specified the maximum ambient temperature for use in charging mode of 40 ˚C
and for use in non-charge mode of 45 ˚C.
Adapter is not shipped with the product, but if used adaptor, need to select output rated of DC5V,
0.8A min and ambient 40 ˚C minimum.
The minimum distance between the user and/or any bystander and the radiating structure
of the transmitter is 20cm.
This radio equipment operates with the following frequency bands and maximum radio-
：
frequency power
：
GSM900 32dBm
G： SM1800 29dBm
Band1:21dBm
Band8:21dBm
Complies with the essential requirements of Article 3 of the RED /EC Directive, if used for
its intended use and that the following standards have been applied:
1. Health (Article 3.1(a) of the RED Directive)
■ EN 62311: 2008
2. Safety (Article 3.1(a) of the RED Directive)
Applied Standard(s):
■ EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
3. Electromagnetic compatibility (Article 3.1 (b) of the RED Directive)
Applied Standard(s):
■ EN 301 489-1 V1.9.2/-7 V1.3.1
4. Radio frequency spectrum usage (Article 3.2 of the RED Directive)
Applied Standard(s):
■ EN 301 511 V9.0.2
All the reports of the applied standards have the Positive Opinion of Notified Body:
PHONEIX TESTLAB, Königswinkel 10 D-32825 Blomberg, Germany
Identification mark: (Notified Body) CE
Uitbreidingsstraat 84, Berchem, Antwerpen, 2600,
Belgium |
The technical documentation relevant to the above equipment will be held at: Locus Solutions
FCC Regulations:

Confidential
Preliminary-Subject to Change
2013 Locus Solutions Page 5 of 6
●This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
●This device has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiated radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user‘s authority to operate the equipment.
Cet appareil est confo rme aux dispositions de la partie 15 des règles de la FCC et
des nor mes CNR d'In dustrie Canada sur les appareils radio exempts de licence. Son
utilisation est assujettie aux deux conditions suivantes : (1) Cet appareil ne doit pas
causer d'interférence nuisible; et (2) cet appareil doit accepter toute interférence
reçue, y compris l 'interférence qui pourrait causer un fonctionnement non désiré.
Cet équipe ment a ététe stéet j ugéconforme au x limites d'un appareil nu mérique de la
Classe B, en vertu de la partie 15 des règles de la FCC et de la NMB-003 canadienne.
Ces li mites sont conçues pour fournir une protection raisonnable contre
l'interférence nuisible dans une
installation résidentielle. Cet équipement génère, utilise et peut émettre de l'énergie
radiofréquence et, s'il n'est pas installéet utiliséconfor mément aux instructions, peut
causer une interférence nuisible
aux communications r adio. Toutefois, il n'es t pas garanti que l'interférence ne se
produira pas dans une installation particuli ère. Si cet équipement cause une
interférence nuisible àla réception radio ou d e pro gra mmes de télévision, laquelle
peut être déter minée e n é tei gnant et en allu mant l'équipe ment, l'usager est
encouragéàessayer de corriger l 'interférence par l 'une ou plusieurs des mesures
suivantes.
• Réorientez ou relocalisez l'antenne de réce ption.
• Augmentez la séparation entre l'équipement et le receveur.
• Co nnectez l 'équipement àune prise sur un circuit différent de celui auquel de le
receveur est connecté.
• Co nsultez le vendeur ou un technicien radio/de télévision pour o btenir de l 'aide.
La FCC ou Industrie Canada peut vous obliger àarrêter d'utiliser votre appareil si
une telle interférence ne peut pas être éliminée. GO Real -Ti me 2G/3G n'a pas
approuvéles chan gements ou modifications apportés à cet appareil
par l'usager. Tous les chan gements ou modifications apportés peuvent entraîner la
révocation de l'autorisation d 'utilisation de l'appareil.

Confidential
Preliminary-Subject to Change
2013 Locus Solutions Page 6 of 6
RF Exposure Infor mation
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In
order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity
to the antenna shall not be less than 20cm (8 inches) during normal operation.
ISED Notice
This device complies with Innovation, Science and Economic Development Canada license-exempt
RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation
of the device.
Le présent appareil est conforme aux CNR Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en
Innovation, Science and Economic Development Canada ICES-003 Compliance Label:
CAN ICES-3 (B)/NMB-3(B)
IC: 10124A-101009
ISED RF Exposure Statement
This device complies with ISED RSS-102 RF exposure limits set forth for an uncontrolled
environment. In order to avoid the possibility of exceeding the IC RSS-102 RF exposure limits, human
proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.
Cet appareil est conforme aux limites d'exposition aux rayonnements de la CNR-102 définies pour un
environnement non contrôlé. Afin d'éviter la possibilité de dépasser les limites d'exposition aux
fréquences radio de la CNR-102, la proximité humaine à l'antenne ne doit pas être inférieure à 20 cm
(8 pouces) pendant le fonctionnement normal.