Logicube WriteProtect BAY User manual

Logicube WriteProtect™ BAY User’s Manual I
WriteProtect™BAY User’s Manual
Logicube, Inc.
Chatsworth, CA 91311
USA
Phone: [phone]
Fax: [phone]
Version: 1.07
Date: 11/29/16
MAN-WP-BAY

Logicube WriteProtect™ BAY User’s Manual I
Limitation of Liability and Warranty Information
Logicube Disclaimer
LOGICUBE IS NOT LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING, BUT NOT
LIMITED TO PROPERTY DAMAGE, LOSS OF TIME OR DATA FROM USE OF A LOGICUBE PRODUCT, OR ANY
OTHER DAMAGES RESULTING FROM PRODUCT MALFUNCTION OR FAILURE OF (INCLUDING WITHOUT
LIMITATION, THOSE RESULTING FROM: (1) RELIANCE ON THE MATERIALS PRESENTED, (2) COSTS OF
REPLACEMENT GOODS, (3) LOSS OF USE, DATA OR PROFITS, (4) DELAYS OR BUSINESS INTERRUPTIONS, (5)
AND ANY THEORY OF LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
(OR FROM DELAYS IN SERVICING OR INABILITY TO RENDER SERVICE ON ANY) LOGICUBE PRODUCT.
LOGICUBE MAKES EVERY EFFORT TO ENSURE PROPER OPERATION OF ALL PRODUCTS. HOWEVER, THE
CUSTOMER IS RESPONSIBLE TO VERIFY THAT THE OUTPUT OF LOGICUBE PRODUCT MEETS THE
CUSTOMER’S QUALITY REQUIREMENT. THE CUSTOMER FURTHER ACKNOWLEDGES THAT IMPROPER
OPERATION OF LOGICUBE PRODUCT AND/OR SOFTWARE, OR HARDWARE PROBLEMS, CAN CAUSE LOSS
OF DATA, DEFECTIVE FORMATTING, OR DATA LOADING. LOGICUBE WILL MAKE EFFORTS TO SOLVE OR
REPAIR ANY PROBLEMS IDENTIFIED BY CUSTOMER, EITHER UNDER WARRANTY OR ON A TIME AND
MATERIALS BASIS.
Warranty
DISCLAIMER
IMPORTANT - PLEASE READ THE TERMS OF THIS AGREEMENT CAREFULLY. BY INSTALLING OR USING
LOGICUBE PRODUCTS, YOU AGREE TO BE BOUND BY THIS AGREEMENT.
IN NO EVENT WILL LOGICUBE BE LIABLE (WHETHER UNDER THIS AGREEMENT, RESULTING FROM THE
PERFORMANCE OR USE OF LOGICUBE PRODUCTS, OR OTHERWISE) FOR ANY AMOUNTS REPRESENTING
LOSS OF PROFITS, LOSS OR INACCURACY OF DATA, LOSS OR DELAYS OF BUSINESS, LOSS OF TIME, COSTS
OF PROCUREMENT OF SUBSTITUTE GOODS, SERVICES, OR TECHNOLOGY, PROPERTY DAMAGE, OR
INDIRECT, CONSEQUENTIAL, OR PUNITIVE DAMAGES OF A PURCHASER OR USER OF LOGICUBE PRODUCTS
OR ANY THIRD PARTY. LOGICUBE’S AGGREGATE LIABILITY IN CONTRACT, TORT, OR OTHERWISE
(WHETHER UNDER THIS AGREEMENT, RESULTING FROM THE PERFORMANCE OR USE OF LOGICUBE
PRODUCTS, OR OTHERWISE) TO A PURCHASER OR USER OF LOGICUBE PRODUCTS SHALL BE LIMITED TO
THE AMOUNT PAID BY THE PURCHASER FOR THE LOGICUBE PRODUCT. THIS LIMITATION OF LIABILITY
WILL BE EFFECTIVE EVEN IF LOGICUBE HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES.

Logicube WriteProtect™ BAY User’s Manual II
LOGICUBE MAKES EVERY EFFORT TO ENSURE PROPER OPERATION OF ITS PRODUCTS. HOWEVER, THE
PURCHASER IS RESPONSIBLE FOR VERIFYING THAT THE OUTPUT OF A LOGICUBE PRODUCT MEETS THE
PURCHASER’S REQUIREMENTS. THE PURCHASER FURTHER ACKNOWLEDGES THAT IMPROPER OPERATION
OF LOGICUBE PRODUCTS CAN CAUSE LOSS OF DATA, DEFECTIVE FORMATTING, OR DEFECTIVE DATA
LOADING. LOGICUBE WILL MAKE EFFORTS TO SOLVE OR REPAIR ANY PROBLEMS IDENTIFIED BY
PURCHASER, EITHER UNDER THE WARRANTY SET FORTH BELOW OR ON A TIME AND MATERIALS BASIS.
LIMITED WARRANTY
FOR ONE YEAR FROM THE DATE OF SALE (THE “WARRANTY PERIOD”) LOGICUBE WARRANTS THAT THE
PRODUCT (EXCLUDING CABLES, ADAPTERS, AND OTHER “CONSUMABLE” ITEMS) IS FREE FROM
MANUFACTURING DEFECTS IN MATERIAL AND WORKMANSHIP. THIS LIMITED WARRANTY COVERS
DEFECTS ENCOUNTERED IN THE NORMAL USE OF THE PRODUCT DURING THE WARRANTY PERIOD AND
DOES NOT APPLY TO: PRODUCTS DAMAGED DUE TO PHYSICAL ABUSE, MISHANDLING, ACCIDENT,
NEGLIGENCE, OR FAILURE TO FOLLOW ALL OPERATING INSTRUCTIONS CONTAINED IN THE OPERATING
MANUAL; PRODUCTS WHICH ARE MODIFIED; PRODUCTS WHICH ARE USED IN ANY MANNER OTHER THAN
THE MANNER FOR WHICH THEY WERE INTENDED, AS SET FORTH IN THE OPERATING MANUAL; PRODUCTS
WHICH ARE DAMAGED OR DEFECTS CAUSED BY THE USE OF UNAUTHORIZED PARTS OR BY
UNAUTHORIZED SERVICE; PRODUCTS DAMAGED DUE TO UNSUITABLE OPERATING OR PHYSICAL
CONDITIONS DIFFERING FROM THOSE RECOMMENDED IN THE OPERATING MANUAL OR PRODUCT
SPECIFICATIONS PROVIDED BY LOGICUBE; ANY PRODUCT WHICH HAS HAD ANY OF ITS SERIAL NUMBERS
ALTERED OR REMOVED; OR ANY PRODUCT DAMAGED DUE TO IMPROPER PACKAGING OF THE WARRANTY
RETURN TO LOGICUBE. AT LOGICUBE’S OPTION, ANY PRODUCT PROVEN TO BE DEFECTIVE WITHIN THE
WARRANTY PERIOD WILL EITHER BE REPAIRED OR REPLACED USING NEW OR REFURBISHED
COMPONENTS AT NO COST. THIS WARRANTY IS THE SOLE AND EXCLUSIVE REMEDY FOR DEFECTIVE
PRODUCTS. IF A PRODUCT IS HAS BECOME OBSOLETE OR IS NO LONGER SUPPORTED BY LOGICUBE THE
PRODUCT MAY BE REPLACED WITH AN EQUIVALENT OR SUCCESSOR PRODUCT AT LOGICUBE’S
DISCRETION. THIS WARRANTY EXTENDS ONLY TO THE END PURCHASER OF LOGICUBE PRODUCTS. THIS
WARRANTY DOES NOT APPLY TO, AND IS NOT FOR THE BENEFIT OF, RESELLERS OR DISTRIBUTORS OF
LOGICUBE PRODUCTS. UNLESS OTHERWISE AGREED IN WRITING BY LOGICUBE, NO WARRANTY IS
PROVIDED TO RESELLERS OR DISTRIBUTORS OF LOGICUBE PRODUCTS.
IN ORDER TO RECEIVE WARRANTY SERVICES CONTACT LOGICUBE’S TECHNICAL SUPPORT DEPARTMENT
VIA PHONE OR E-MAIL. PRODUCTS RETURNED TO LOGICUBE FOR REPAIR UNDER WARRANTY MUST
REFERENCE A LOGICUBE RETURN MATERIAL AUTHORIZATION NUMBER (“RMA”). ANY PRODUCT RECEIVED
BY LOGICUBE WITHOUT AN RMA# WILL BE REFUSED AND RETURNED TO PURCHASER. THE PURCHASER
MUST CONTACT LOGICUBE’S TECHNICAL SUPPORT DEPARTMENT VIA E-MAIL
([e-mail]) OR VIA PHONE AT [phone] OPT. 3 TO OBTAIN A VALID RMA#. THE
PURCHASER MAY BE REQUIRED TO PERFORM CERTAIN DIAGNOSTIC TESTS ON A PRODUCT PRIOR TO
LOGICUBE ISSUING AN RMA#. THE PURCHASER MUST PROVIDE THE PRODUCT MODEL, SERIAL NUMBER,
PURCHASER NAME AND ADDRESS, EMAIL ADDRESS AND A DESCRIPTION OF THE PROBLEM WITH AS
MUCH DETAIL AS POSSIBLE. AT LOGICUBE’S SOLE AND ABSOLUTE DISCRETION, REASONABLE TELEPHONE
AND EMAIL SUPPORT MAY ALSO BE AVAILABLE FOR THE LIFE OF THE PRODUCT AS DEFINED BY LOGICUBE.
EXCEPT AS OTHERWISE SPECIFICALLY PROVIDED IN THIS AGREEMENT, LOGICUBE PRODUCTS ARE
PROVIDED AS-IS AND AS-AVAILABLE, AND LOGICUBE DISCLAIMS ANY AND ALL OTHER WARRANTIES
(WHETHER EXPRESS, IMPLIED, OR STATUTORY) INCLUDING, WITHOUT LIMITATION, ANY WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NONINFRINGEMENT OF THIRD PARTY
RIGHTS.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE
ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM JURISDICTION TO JURISDICTION.

Logicube WriteProtect™ BAY User’s Manual III
RoHS Certificate of Compliance
LOGICUBE PRODUCTS COMPLY WITH THE EUROPEAN UNION RESTRICTION OF THE USE OF CERTAIN
HAZARDOUS SUBSTANCES IN ELECTRONIC EQUIPMENT, ROHS DIRECTIVE (2002/95/EC).
THE ROHS DIRECTIVE PROHIBITS THE SALE OF CERTAIN ELECTRONIC EQUIPMENT CONTAINING SOME
HAZARDOUS SUBSTANCES SUCH AS MERCURY, LEAD, CADMIUM, HEXAVALENT CHROMIUM AND CERTAIN
FLAME-RETARDANTS IN THE EUROPEAN UNION. THIS DIRECTIVE APPLIES TO ELECTRONIC PRODUCTS
PLACED ON THE EU MARKET AFTER JULY 1, 2006.
Logicube Technical Support Contact Information
1. By website: www.logicube.com
2. By email: [e-mail]
3. By telephone: 1 - [phone] ext. 3 between the hours of 7am –5pm PST, Monday through
Friday, excluding U.S. legal holidays.

Logicube WriteProtect™ BAY User’s Manual I
Table of Contents
WRITEPROTECT™ BAY USER’S MANUAL ........................................................................I
LIMITATION OF LIABILITY AND WARRANTY INFORMATION ...........................................I
LOGICUBE DISCLAIMER ........................................................................................................................ I
WARRANTY ....................................................................................................................................... I
ROHS CERTIFICATE OF COMPLIANCE.................................................................................................... III
LOGICUBE TECHNICAL SUPPORT CONTACT INFORMATION........................................................................ III
TABLE OF CONTENTS.....................................................................................................I
1: INTRODUCTION ......................................................................................................1
1.0 INTRODUCTION TO THE WRITEPROTECT BAY.................................................................................. 1
1.1 FEATURES ................................................................................................................................. 2
1.2 SPECIFICATIONS.......................................................................................................................... 2
1.3 IN THE BOX ............................................................................................................................... 2
1.4 ADDITIONAL OPTIONS ................................................................................................................. 3
2: GETTING STARTED..................................................................................................4
2.0 OVERVIEW OF THE WRITEPROTECT BAY ........................................................................................ 4
2.1 CONNECTING THE WRITEPROTECT BAY TO A FORENSIC WORKSTATION ............................................... 5
2.2 CONNECTING VARIOUS DRIVE TYPES............................................................................................... 6
2.3 USING USB/FIREWIRE/ESATA ENCLOSURES OR EXTERNAL DRIVES.................................................... 7
2.4 LEDS........................................................................................................................................ 7
3: QUICK START.......................................................................................................... 9
3.0 QUICK START GUIDE ................................................................................................................... 9
3.1 REGISTRY OPTIMIZATION ............................................................................................................. 9
3.2 CONNECTED DRIVES.................................................................................................................. 10
4: REMOTE CONNECTIVITY ....................................................................................... 12
4.0 REMOTE CONNECTIVITY INTRODUCTION....................................................................................... 12
4.1 CONNECTING TO THE WEB INTERFACE ......................................................................................... 12
4.2 USAGE.................................................................................................................................... 12
5: USING THE WEB INTERFACE.................................................................................. 13
5.0 WEB INTERFACE INTRODUCTION .................................................................................................13
5.1 USB DEVICE............................................................................................................................ 13
5.1.1 Drives ........................................................................................................................... 14
5.1.2 HPA/DCO...................................................................................................................... 15
5.1.3 Exports ......................................................................................................................... 16

Logicube WriteProtect™ BAY User’s Manual II
5.2 FILE BROWSER ......................................................................................................................... 16
5.3 WRITE PROTECT STATISTICS .......................................................................................................16
5.3.1 About............................................................................................................................ 16
5.3.2 Adv. Drive Statistics......................................................................................................17
5.4 SYSTEM SETTINGS..................................................................................................................... 17
5.4.1 User Profiles/Configurations........................................................................................ 18
5.4.2 Passwords .................................................................................................................... 20
5.4.2.1 Key ........................................................................................................................ 20
5.4.2.2 Auto Lock .............................................................................................................. 20
5.4.3 Language/Time Zone ................................................................................................... 22
5.4.3.1 Language .............................................................................................................. 22
5.4.3.2 Time Zone ............................................................................................................. 22
5.4.4 USB Device ...................................................................................................................23
5.4.5 HPA............................................................................................................................... 24
5.5 NETWORK SETTINGS .................................................................................................................25
5.5.1 Services ........................................................................................................................ 25
5.5.2 HTTP Proxy..................................................................................................................... 26
5.6 SOFTWARE UPDATES.................................................................................................................26
5.7 POWER OFF ............................................................................................................................ 26
6: UPDATING THE WRITEPROTECT BAY SOFTWARE................................................... 27
6.0 LOADING NEW SOFTWARE.........................................................................................................27
6.1 SOFTWARE LOADING INSTRUCTIONS ............................................................................................ 27
6.1.1 From Network –Via the web....................................................................................... 28
6.1.2 From USB Drive –Via software download................................................................... 28
6.2 FIRMWARE LOADING INSTRUCTIONS............................................................................................ 29
TECHNICAL SUPPORT INFORMATION ................................................................................................... 30

Logicube WriteProtect BAY User’s Manual 1
1: Introduction
1.0 Introduction to the WriteProtect BAY
The WriteProtect™ BAY write-blocker provides secure, read-only, write-blocked access to SAS, SATA,
USB 3.0, FireWire™, and PATA/IDE (PATA/IDE supported with an adapter) suspect hard drives. Extremely
fast performance is powered by a SuperSpeed USB 3.0 host connection to easily manage large capacity
hard drives. The WriteProtect BAY is the only portable write-blocker on the market that provides
support for 5 different storage technologies in a 5.25” half height design that fits into the drive bay of
your forensic workstation. Logicube, a pioneer in the digital forensic industry, delivers an easy to use,
reliable and professional forensic write-blocking solution.

INTRODUCTION
Logicube WriteProtect™ BAY User’s Manual 2
1.1 Features
The standalone WriteProtect-BAY mounts into a standard 5.25” half-height forensic workstation
drive bay for efficient imaging and preview tasks in the lab.
Superspeed USB 3.0 host connection for extremely fast operation.
Built-in, read-only, write-blocked support for SAS/SATA/USB 3.0/2.0/1.1/FW400/800 storage
technologies, an adapter is included to support 2.5”/3.5” IDE drives.
Multiple source drives can be connected to the WriteProtect and imaged, using your forensic
imaging software, simultaneously to shorten processing time.
Features 2 SAS/SATA drive ports, 1 USB 3.0 port, 1 FireWire port, 1 Gigabit Ethernet port.
Support for IDE, 1.8” IDE, 1.8” ZIF, mSATA, microSATA, eSATA and flash media is available using
optional adapters.
Use the browser-based user interface to manage all WriteProtect operations including software
updates. Connect to your network using the WriteProtect’s Gigabit Ethernet port.
Preview drives connected to WriteProtect using the browser-based user interface.
HPA/DCO detection and capture supported via the browser-based user interface.
5 LEDs for power, host, device, activity, HPA/DCO detection allow you to easily monitor all
processes.
Compatible with forensic acquisition and analysis software.
1.2 Specifications
1.3 In the Box
The following items are included with WriteProtect BAY:
2 SAS/SATA power & data cables
1 FireWire cable
1 USB 3.0 Type A Male to Micro-B Male
1 Cat 6 network cable
1 2.5”/3.5” IDE to SATA adapter
1 Dual 4-pin molex to 6-pin PCIe Y adapter

INTRODUCTION
Logicube WriteProtect™ BAY User’s Manual 3
1.4 Additional Options
The following options are available for the WriteProtect BAY:
eSATA cable
mSATA adapter
Flash media reader for compact flash, SD cards and other flash media
1.8” IDE to SATA adapter
1.8” IDE ZIF to SATA adapter
1.8” microSATA adapter
Special Icons –Throughout this manual, there are two icons that can be seen. Please
pay close attention when any of these two icons are found. These icons highlight additional information
or important warnings on specific topics.
WARNINGS:
Avoid dropping the Logicube WriteProtect BAY or subjecting it to
sharp jolts. When in use, place it on a flat surface.
Keep the unit dry. If the WriteProtect BAY needs to be cleaned,
use a lightly damp, lint free cloth. Avoid using soap or other
cleaning agents particularly those containing bleach, ammonia,
alcohol or other harsh chemicals.
Do not attempt to service or open the WriteProtect BAY. Doing
so may void the warranty. If the unit requires service, please
contact Logicube Technical Support for assistance.

Logicube WriteProtect BAY User’s Manual 4
2: Getting Started
2.0 Overview of the WriteProtect BAY
WriteProtect BAY –Right angled view

GETTING STARTED
Logicube WriteProtect BAY User’s Manual 5
WriteProtect BAY - Left angled view
WriteProtect BAY –Back view
2.1 Connecting the WriteProtect BAY to a forensic workstation
To mount the WriteProtect BAY to a 5.25” bay on a forensic workstation, please reference the
workstation’s user’s manual or the case manufacturer’s manual.
It is recommended the workstation be powered off when mounting and
connecting the WriteProtect BAY.
The WriteProtect BAY is powered by a 6-pin PCIe power connector. It comes with dual 4-pin
molex to 6-pin PCIe Y adapter for power supplies that do not have a 6-pin PCIe power output.
Attach a 6-pin PCIe power connector from the power supply or use the adapter to utilize two 4-
pin molex connectors. This will provide power to the WriteProtect BAY.
Connect the USB 3.0 host cable to an available USB port.
The WriteProtect BAY is now ready to be used and will turn on when the computer is turned on.

GETTING STARTED
Logicube WriteProtect BAY User’s Manual 6
The PWR LED will blink for up to 30 seconds when turned on. The WriteProtect
BAY will be ready to use when the PWR LED turns solid green.
There are three ways of turning the WriteProtect BAY off:
1. Shut down the forensic analysis computer. The WriteProtect BAY will turn off with the
computer.
2. Press and immediately release the power button on the WriteProtect BAY. The Power
LED will start blinking as the WriteProtect BAY begins to shut down. The Power LED and
the fans will turn off within 30 seconds. When the Power LED turns off, the WriteProtect
BAY has fully shut down.
3. Using the Graphical User Interface (GUI) via a browser through a remote connection,
navigate to the Power Off screen and click the Power Off icon. The Power LED will start
blinking as the WriteProtect BAY begins to shut down. The Power LED and the fans will
turn off within 30 seconds. When the Power LED turns off, the WriteProtect BAY has
fully shut down.
2.2 Connecting various drive types
Cables and adapters are available for the following drive types:
SAS
SATA
USB
FireWire
2.5” and 3.5” PATA/IDE
eSATA cable (optional)
mSATA adapter (optional)
Flash media reader for compact flash, SD cards and other flash media (optional)
1.8” IDE to SATA adapter (optional)
1.8” IDE ZIF to SATA adapter (optional)
1.8” microSATA adapter (optional)

GETTING STARTED
Logicube WriteProtect BAY User’s Manual 7
The SAS/SATA cable must be matched with the SAS and Power (PWR) ports. For example, SAS 1
goes with PWR 1 and SAS 2 goes with PWR 2.
Drives do not have to be connected in any order. For example, a single SATA drive
does not have to be connected to the SAS/SATA S1 port. It can be connected to
the SAS/SATA S2 port without having anything connected to the S1 port.
Any combination of drives can be connected at the same time, up to 4 drives
connecting to all available ports.
2.3 Using USB/FireWire/eSATA Enclosures or External Drives
When using drives that came from a USB, FireWire, or eSATA enclosure, or external drives, it is
highly recommended to leave the drive inside the enclosure. USB enclosures typically have an
on-board controller that may be necessary to read the drive properly. Taking the drive out of
the enclosure could cause any device (including computers) not to read the drive contents
properly.
2.4 LEDs
The WriteProtect BAY has five (5) LEDs:
PWR –Power LED
On –The WriteProtect is powered on
Blinking –This LED will blink while the WriteProtect is being turned ON or OFF
Off - The WriteProtect is turned off
HOST –Detects a link connection between the WriteProtect and the host computer
On –Detects an active link between the WriteProtect and host computer
Off –There is no active link between the WriteProtect and host computer

GETTING STARTED
Logicube WriteProtect BAY User’s Manual 8
DEV –Device LED
On –This LED is ON when a drive is connected (SATA, SAS, USB, FireWire, etc.)
Off –This LED is OFF when there are no drives connected
ACT –Activity LED
Blinking –Detects activity on the connected drive
Off –No activity on the connected drive
HPA/DCO –HPA and/or DCO detection
On –Detects the presence of an HPA and/or DCO on the connected drive
Off –Does not detect the presence of an HPA and/or DCO on the connected drive

Logicube WriteProtect BAY User’s Manual 9
3: Quick Start
3.0 Quick Start Guide
This chapter gives a basic overview and steps on how to set up the WriteProtect.
Two steps must be performed to use the WriteProtect:
Turn the WriteProtect on
Connect at least one drive to the WriteProtect
Optional: Connect the WriteProtect to a network using a Cat5e or Cat6 network cable for
remote connectivity to be able to use the built-in file browsing capabilities, configure, or
update the software of the WriteProtect.
3.1 Registry Optimization
Logicube recommends a registry entry to optimize the USB 3.0 transfer speeds for windows 7
and Windows 8/8.1. No registry optimization is needed for Windows 10.
The registry entries can be downloaded from:
http://updates.logicube.com/WriteProtectOptimization/WriteProtect_Optimization.zip
Extract the contents of the ZIP file to a folder on your computer. You should see two files:
Logicube_WriteProtect_Optimization_Win7.reg
Logicube_WriteProtect_Optimization_Win8.reg
Microsoft recommends backing up the registry andany important/valued
data before making any changes to the registry. Please search Microsoft’s
support site for instructions on how to back up the Windows registry.
To import the optimization registry entry:
1. Make sure you are logged in to a Windows 7 or 8/8.1 computer on an account with
administrator rights
2. Double-click the appropriate registry file
(Logicube_WriteProtect_Optimization_Win7.reg for Windows 7 computers and
Logicube_WriteProtect_Optimization_Win8.reg 8.reg for Windows 8/8.1 computers).

QUICK START
Logicube WriteProtect BAY User’s Manual 10
3. Windows should prompt you asking if you are sure you want to allow the program (the
registry file) to make changes to yoru computer. Select Yes. You may also be prompted
with a warning about adding infromation to the registry may cause components to stop
working correctly. Please select Yes to continue adding the registry entry.
4. When the registry entry has been imported, you should see a confirmation window
stating it has been successfully added to the registry. Once successfully added, we
recommend restarting the computer.
3.2 Connected Drives
Depending on the Operating System on the computer, drives connected to the WriteProtect
may or may not be automatically mounted. Windows should automatically assign a drive letter
to partitions that it can recognize.
Disk Management will show the drives as “Read Only”:
If at least one drive is already connected and a second, third, or fourth drive is
added, Windows may not automatically detect the added drives. It is
recommended to go to Disk Management, click Action, then click Refresh.
When drives are disconnected, refreshing Disk Management may also be
required to refresh the list of connected drives.

QUICK START
Logicube WriteProtect BAY User’s Manual 11
FireWire drives may not be seen by the computer when the FireWire drive is
already connected to the WriteProtect before the WriteProtect is turned on.
If FireWire drives are not detected, disconnect the FireWire drive from the
WriteProtect, wait a few seconds, then re-connect the FireWire drive.
HPA/DCO can be managed and configured through the web browser interface
(additional information TBD). Third party tools can always be used to manage
HPA/DCO.

Logicube WriteProtect BAY User’s Manual 12
4: Remote Connectivity
4.0 Remote Connectivity Introduction
The WriteProtect comes with a gigabit network connection. Connecting the WriteProtect to a
network allows remote access from any computer within the same network using a supported
Internet browser (Chrome or Firefox). A network connection with Internet access also allows the
WriteProtect software to be updated using the FROM NETWORK option.
The WriteProtect is configured for DHCP.
4.1 Connecting to the Web Interface
Using a supported web browser, go to the WriteProtect’s hostname. The hostname will be:
http://wp-XXXXXX where XXXXXX is the 6 digit serial number of the WriteProtect. The serial
number can be found on a sticker underneath the WriteProtect. The WriteProtect’s web
interface will appear on the browser screen.
Google Chrome and Mozilla Firefox are the recommended browsers. Other browsers may not
display the Graphical User Interface correctly.
On some browsers or Operating Systems, the WriteProtect will need to be
accessed by browsing to http://wp-XXXXXX.local/.
4.2 Usage
The web interface can be used for built-in file browsing capabilities, configuration, or software
updates for the WriteProtect. The built-in file browser can recognize many different file systems
and can be a useful tool when the computer being used does not have the ability to see the
connect drive’s file system or contents. See Section 5.0 Web Interface Introduction for details
on the web interface.

Logicube WriteProtect BAY User’s Manual 13
5: Using the Web Interface
5.0 Web Interface Introduction
The Web Interface allows the user the following capabilities:
Advanced configuration and settings
File Browsing
Software and firmware updates
The following sections give a brief explanation of each screen on the web interface.
5.1 USB Device
This screen has three tabs: Drives, HPA/DCO, and Exports.

WEB INTERFACE
Logicube WriteProtect BAY User’s Manual 14
5.1.1 Drives
This screen allows the user to see basic information about drives connected to
the device.
The icon shows additional information about the drive.
If a drive has an HPA or DCO detected, the following icon will be displayed:
Clicking the icon will show additional details of about the drive.