logika WL-ZSPDBPW-MT-02 User manual

© 2019 Logika Limited
Smart Contact Sensor
WL- ZSPDBPW-MT-02
Product Manual
Version 1.0

1
Logika Limited
E
-Centre, Massey University, Gate 5, Oaklands Road
Albany, Auckland 0632, New Zealand
www.logika.nz
·[e-mail]
Introduction
Thank you for choosing Logika. Please take a moment to carefully read through the manual to
ensure safe and proper installation and use.
•Before use, the product must be properly installed as described in this manual by a qualified
technician.
•The product should be used with the supplied accessories.
•Do not disassemble or modify the product.
•Logika is not responsible for any loss due to improper installation or use of this product.
•Please visit our official website at www.logika.nz for more information.
•You can also contact us at the following email address: [e-mail].

2
Device Layout
Battery Box
System Indicator
Multi-Function Key
Main Body Magnetic Body

3
Features
•Communication Mode: IEEE 802.15.4 Zigbee.
•Battery operated and easy to install.
•Remote monitor the opening/closing state of door or window.
•As a security device, pre-set alarm devices can be triggered and send an alert to the phone.
•As a trigger device, it can be linked to turn on the lights or any other smart device or scene.
•Low power consumption, energy saving.
Specifications
Communication Protocol IEEE 802.15.4 (ZigBee/HA1.2)
Antenna Type Internal Antenna
Power DC 3V
Standby Current ≤4 μA
Battery Type CR2 × 1
Opening and Closing Current ≤2 μA at Opening ≤4 μA at Closing
Alarm Distance 20mm
Panel Size (Length × Width x Height)
Main Body 63×23×21mm
Magnetic Body 63×10×15mm
Material & Colour PC, White
Flame Retardant Rating UL94 V-2
Working Temperature -10°C to +45°C
Working Humidity ≤95%RH (Noncondensing)
Installation Method Door and Window Type
Net Weight 37g
Storage Temperature -20°C to +60°C

4
Installation Steps
Hardware Installation
1) Remove the base from both the Main Body and Magnetic Body by sliding off the covers.
Main Body Main Body Base Magnetic Body Base Magnetic Body
2) Open the battery cover an insert the CR2 battery as shown.
Battery Cover
Battery

5
3) Screw the Main Body Base and Magnetic Body Base to the appropriate location on your door
or window, using the supplied screws.
4) Once the bases are fixed to the door/window, slide the Main Body and Magnetic Body back
onto their respective base.
5) The hardware installation is now complete.
Door Frame
Main Body Base
Door
Magnetic Body Base
Main Body
Magnetic Body

6
Adding the Device to the Smart Home Network
Use the Logika Smart Home app to add the device to the Smart Home system. Please refer to the
Logika Smart Mobile App user guide which will take you through the process of adding smart
devices to the system.
Refer to the information below to locate the device in the Device Add screen. Once selected, the app
will walk you through how to add the device to the system.
Device Category:
Security
Device Name:
Contact Sensor

7
Device Functions
When the device is first powered on, it will normally automatically attempt to connect to the Zigbee
Smart Home network. The System Indicator light will flash as it’s searching for the network. If it
connects, the light will remain on for 2 seconds and then go out.
If this does not happen, you can manually connect via the mobile app and follow the instructions
below.
Join the Zigbee Network
Press the Multi-Function Button once. The System Indicator light will start flashing, signifying it’s
searching for the network.
When it successfully connects, the System Indicator light will stay solid for 2 seconds then go out.
Quit the Zigbee Network
Long press the Multi-Function Button for 6 seconds. The System Indicator light will flash 4 times and
go out. The device has now been successfully removed from the network.
System Indicator Light
Multi-Functional Button

8
Troubleshooting
The device cannot be added to the Zigbee network.
The device may be registered to another network. In rare occasions this can happen if the device
was not removed from the test network at the factory.
Perform the Quit the Zigbee Network procedure mentioned in Device Functions section to clear this
setting. You should now be free to add the device to the local smart network.
The issue you are experiencing is not mentioned here.
Please contact us at [e-mail] with your issue and we will do our utmost to help!