logika WL-ZSSMBPW-FD-01 User manual

© 2019 Logika Limited
Smart Water Leakage Sensor
WL-ZSSMBPW-FD-01
Product Manual
Version 1.0

1
Logika Limited
E
-Centre, Massey University, Gate 5, Oaklands Road
Albany, Auckland 0632, New Zealand
www.logika.nz
·[e-mail]
Introduction
Thank you for choosing Logika. Please take a moment to carefully read through the manual to
ensure safe and proper installation and use.
•Before use, the product must be properly installed as described in this manual by a qualified
technician.
•The product should be used with the supplied accessories.
•Do not disassemble or modify the product.
•Logika is not responsible for any loss due to improper installation or use of this product.
•Please visit our official website at www.logika.nz for more information.
•You can also contact us at the following email address: [e-mail].

2
Device Layout
Water Sensors
Upper Shell
Lower Shell
Top
Bottom
Multi-Function Button
System Indicator
Battery Compartment
Top
Bottom

3
Features
•Communication Mode: IEEE 802.15.4 Zigbee.
•Equipped with high-sensitive water contact probe.
•Real-time detection of water leaks and sends out alerts.
•Group linkage with relevant smart devices like Smart Automatic Manipulator to turn off
water valve.
•Water leakage can be monitored remotely via the mobile application.
•Battery operated and easy to install.
Specifications
Panel Size (Diameter*Thickness) 69x29mm
Material & Colour PC, White
Flame Retardant Rating UL94 V-2
Working Temperature -10°C - +45°C
Working Humidity ≤95%RH (Noncondensing)
Mounting Type Mobile
Net Weight(g) 47g
Storage Temperature -20°C - +60°C
Communication Mode IEEE 802.15.4 (ZigBee/HA1.2)
Antenna Type Internal Antenna
Power Parameter DC 3V
Standby Current ≤2μA
Power Supply CR2 × 1
Water Level ≥1mm

4
Installation Steps
Hardware Installation
The Smart Water Sensor is very simple to install. Just insert a CR2 battery into its compartment and
place the device where you are likely to have water leaks, like under the sink or bath. But, before
you place the device in its final place, be sure to connect the device to the Smart Home network
first.
Once this Is done, align the markers on the Upper and Lower Shells by tightening the Upper Shell
(turning it clockwise) to align fixed point with fixed line.
Battery Location
Align These Markers

5
Adding the Device to the Smart Home Network
Use the Logika Smart Home app to add the device to the Smart Home system. Please refer to the
Logika Smart Mobile App user guide which will take you through the process of adding smart
devices to the system.
Refer to the information below to locate the device in the Device Add screen. Once selected, the app
will walk you through how to add the device to the system.
Device Category:
Security
Device Name:
Water Leakage Sensor

6
Device Functions
When the device is first powered on, it will normally automatically attempt to connect to the Zigbee
Smart Home network. The System Indicator light will flash as it’s searching for the network. If it
connects, the light will remain on for 2 seconds and then go out.
If this does not happen, you can manually connect via the mobile app and follow the instructions
below.
Join the Zigbee Network
Press the Multi-Function Button once. The System Indicator light will start flashing, signifying it’s
searching for the network.
When it successfully connects, the System Indicator light will stay solid for 2 seconds then go out.
Quit the Zigbee Network
Long press the Multi-Function Button for 6 seconds. The System Indicator light will flash 4 times and
go out. The device has now been successfully removed from the network and been reset to the
factory defaults.
User Guide
Water Leakage Detection
When this device detects water leakage, it will send a notification to your mobile app. The System
Indicator will also flash red at the same time. You can bind the device to various devices using the
Housekeeper (Linkage) Task to perform other functions, like sounding an alarm and/or shutting off
the water supply with the Smart Valve Manipulator.
Low Battery
When the battery level is low, an alert will be sent to the mobile app, reminding you to change the
battery.

7
Safety Precautions
• Make sure the device is placed on a fixed flat surface.
• Do not place the device on a metallic surface as this will affect its function.
• Do not submerge in water. The device is designed to pick up water leaks by detecting
shorts across the three terminal probes on the bottom.
• Do not disassemble or refit this product or its accessories.

8
Troubleshooting
The device cannot be added to the Zigbee network.
The device may be registered to another network. In rare occasions this can happen if the device
was not removed from the test network at the factory.
Perform the Quit the Zigbee Network procedure mentioned in Device Functions section to clear this
setting. You should now be free to add the device to the local smart network.
The issue you are experiencing is not mentioned here.
Please contact us at [e-mail] with your issue and we will do our utmost to help!