logika WL-ZSPWBPWBPW-PI11-04 User manual

© 2019 Logika Limited
Smart PIR Motion Detector
WL-ZSPWBPWBPW-PI11-04
Product Manual
Version 1.0

1
Logika Limited
E
-Centre, Massey University, Gate 5, Oaklands Road
Albany, Auckland 0632, New Zealand
www.logika.nz
·[e-mail]
Introduction
Thank you for choosing Logika. Please take a moment to carefully read through the manual to
ensure safe and proper installation and use.
•Before use, the product must be properly installed as described in this manual by a qualified
technician.
•The product should be used with the supplied accessories.
•Do not disassemble or modify the product.
•Logika is not responsible for any loss due to improper installation or use of this product.
•Please visit our official website at www.logika.nz for more information.
•You can also contact us at the following email address: [e-mail].

2
Device Layout
Magnet
System Indicator
Detection Area
Battery Box
Multi-Function Button
Front
Back
Base

3
Features
•Communication Mode: IEEE 802.15.4 Zigbee.
•360° movement detection.
•Battery powered and easy to install.
•Link with other Zigbee devices for multiple actions from controlling lighting to being part of
your overall security system.
Specifications
Communication Mode IEEE 802.15.4 (ZigBee/HA1.2)
Antenna Type Internal Antenna
Power DC 3V
Standby Current 15μA
Battery Type CR2*1
Detection Range Ellipse (Major Axis: 4m, Minor Axis; 3.5m)
Detection Sensitivity Once
Detection Speed 0.2-3.5m/s
Panel Size (Diameter ×
Thickness) 64×38(mm)
Material & Colour PC, White
Flame Retardant Rating UL94 V-2
Working Temperature -10°C - +45°C
Working Humidity ⩽95%RH (Noncondensing)
Installation Method Base-Fixed
Net Weight (g) 50g
Storage Temperature -20°C-+60°C
Installation Height Range 2.3-4(m)

4
Installation Steps
Hardware Installation
There are two options for mounting the Smart PIR Motion Sensor:
Option A: Place the device upright on a suitable flat surface.
Option B: Mount the device on the ceiling or wall as described below.
1) Mark the position on the ceiling/wall and drill the two holes, inserting the wall plugs. Then
screw in the base.
2) Open the battery cover on the PIR Motion Sensor and insert a CR2 battery.
3) Replace the battery cover and attach to the mounted base, adjusting it to a suitable angle
for use.
Base
Wall Plugs
Self-Tapping Screw
Wall/Ceiling
CR2 Battery
Battery Cover

5
Adding the Device to the Smart Home Network
Use the Logika Smart Home app to add the device to the Smart Home system. Please refer to the
Logika Smart Mobile App user guide which will take you through the process of adding smart
devices to the system.
Refer to the information below to locate the device in the Device Add screen. Once selected, the app
will walk you through how to add the device to the system.
Device Category:
Security
Device Name:
PIR Motion Sensor

6
Device Functions
When the device is first powered on, it will normally automatically attempt to connect to the Zigbee
Smart Home network. The System Indicator light will flash as it’s searching for the network. If it
connects, the light will remain on for 2 seconds and then go out.
If this does not happen, you can manually connect via the mobile app and follow the instructions
below.
Join the Zigbee Network
Press the Multi-Function Button once. The System Indicator light will start flashing, signifying it’s
searching for the network.
When it successfully connects, the System Indicator light will stay solid for 2 seconds then go out.
Quit the Zigbee Network
Long press the Multi-Function Button for 6 seconds. The System Indicator light will flash 4 times and
go out. The device has now been successfully removed from the network and been reset to the
factory defaults.

7
User Guide
When the Smart PIR Motion Detector detects any movement, the System Indicator will flash red
momentarily and an alert will be sent to the system, notifying of the movement in the mobile app.
If the battery voltage is running low, an alert will be sent to the mobile app, to remind the user to
replace the battery.
Minor Axis: 3.5m
Major Axis: 4.0m
Major Axis: 4.0m
Minor Axis: 3.5m

8
Troubleshooting
The device cannot be added to the Zigbee network.
The device may be registered to another network. In rare occasions this can happen if the device
was not removed from the test network at the factory.
Perform the Quit the Zigbee Network procedure mentioned in Device Functions section to clear this
setting. You should now be free to add the device to the local smart network.
The issue you are experiencing is not mentioned here.
Please contact us at [e-mail] with your issue and we will do our utmost to help!