LOHBERGER P6 User manual

page 1
Edition July 2010
USER MANUAL
WITH INSTALLATION INSTRUCTIONS
GB
PELLETS MODULE
P6 / P7
LCP 70
LCP 75A
LCP 75B(-Z)
LCP 80 (-Z)

page 2
Important information in this manual is indicated by the following symbols:
NOTE: Instructions for a proper use of the stove. It is the operator’s responsibility to follow these instructions
CAUTION: This sign refers to particularly important notes.
DANGER: This sign indicates important codes of conduct so as to avoid injuries or damage to property.
1. Important notes prior to installation and first starting-up
..........................................................................................4
2. Technical data ...............................................................5
3. Types of operation ........................................................6
4. Functional description...................................................6
Operation with pellets 6
Operation with firewood 6
5. Fuels.............................................................................7
6. Chimney connection......................................................7
Suitable fuels 7
Unsuitable fuels 7
Impermissible fuels 7
7. Air supply connection from outside (accesory).............8
8. Heating connection .......................................................9
9. Electrical connection .....................................................9
10. Requirements for the room where the appliance is situ-
ated...................................................................................9
Floor - load capacity 9
Room and ambient temperatures /humidity 9
Output requirements for heating water 9
Return flow increase 9
11. Fire prevention............................................................10
12. Integration in built-in kitchen.....................................10
Overhead installations 10
Flue gas pipe 10
Floor plate 10
13. Scope of supply...........................................................11
14. Installing the panels...................................................11
15. Operation / Settings ...................................................12
16. Menu – Top level .......................................................12
Switching on the appliance 12
Switching off the appliance 12
Setting the heating output 12
18. Main menu..................................................................13
17. Menu Settings ............................................................13
Keylock 13
Time/Date 13
Automatic mode 14
Heating period 14
Keylock (function) 15
Servicecode 15
Reset 15
19. Menu Informations......................................................16
Summer/Winter 16
Sensors 16
Actuators 17
System/SW Version 17
Operating hours 17
20. Operating the stove for the first time.........................18
21. Heating operation with pellets....................................18
Switching the appliance on 18
Setting the heating output 18
22. Heating operation with firewood ................................19
Ignition of firewood manually operated 19
Ignition of firewood by means of pellet burner 19
Adding of firewood during heating operation with pellets 19
23. External Release / Remote control unit (provided by the
customer) .........................................................................20
24. Switching the appliance off........................................20
25. Display Maintenance / Cleaning .................................20
Display Cleaning 20
Display special cleaning 20
Display maintenance 20
26. Maintenance / Cleaning..............................................21
Vacuum-cleaning firebox 21
28. Resetting safety temperature limiter ..........................22
27. Error messages / Remedy of defects ..........................22
29. Technical data .............................................................24
30. Type test.....................................................................24
Current supply 24
Power input (start / operation) 24
31. Terminal connection diagram......................................25
32. Operating panel language..........................................25
33. Menu diagram ............................................................26
34. After-sales service /Ordering spare parts ..................27
35. The LOHBERGER WARRANTY.......................................27
SHORT INSTRUCTION........................................................28

page 3
With this solid fuel-fired stove you have selected a high-quality product made
by LOHBERGER. Apart from the beautiful and timeless design we attach great
importance to a fully developed combustion technique, high-quality materials
as well as perfect workmanship. Correct handling and proper care are a prereq-
uisite for high reliability and a long service life. Therefore please read the infor-
mation in this user manual carefully. With the above in mind, we are convinced
that this appliance will give satisfactory service for many years.
Your LOHBERGER Heiz + Kochgeräte Technologie GmbH
When installing and starting-up the stove, observe the regulations
and provisions of the building authorities and fire police applicable
at the place of installation as well as the following standards /
instructions:
ÖNORM M7550
Central heating boiler up to 100 °C: definition, requirements, tests,
marking of conformity
ÖNORM M7510/1
Instructions for inspection of central heating systems
ÖNORM M7510/2
Instructions for inspection of central heating systems; standard
values.
ÖNORM B8130
Safety devices
ÖNORM B8131
Closed water heating systems; safety requirements
ÖNORM B8133
Safety requirements water heating systems
DIN 4751 Part 1
Safety equipment for heating systems with supply temperatures up
to 110 °C (120 °C in planning stage)
DIN 4751 Part 2
Safety equipment for heating systems with supply temperatures
up to 110 °C (120 °C in planning stage); open and closed water
heating systems up to 349 kW (300000 kcal/h) with thermostatic
safety device
DIN 4751 Part 4
Safety equipment for heating systems with supply temperatures up
to 120 °C; closed water heating system with static heights exceed-
ing 15 m or rated heating output over 350kW.
DIN 1988
Drinking water supply systems on building sites
(technical regulations).
ÖNORM EN 303-5
Boiler for solid fuels, charged manually or automatically up to 300
kW. Definitions, requirements, tests and marking of conformity
ÖNORM M7135
Densified wood made of untreated wood or bark – wood pellets
or briquettes
ÖNORM M7136
Densified wood made of untreated wood – wood pellets –
quality assurance regarding transport and storage logistics
ÖNORM M7137
Densified wood made of untreated wood – wood pellets –
Requirements regarding the owner’s pellets storage room
TRVB H118
Technical specifications regarding preventive fire protection for au-
tomatic heating systems with wood;

page 4
1. Important notes prior to installation and first starting-up1. Important notes prior to installation and first starting-up
Caution! Possible risks of burns!
The appliance becomes very hot when in use - be especially vigilant that small
children are never in any danger!
Proper Installation and starting-up
Only if the stove has been installed by a trained technician, the safety of the
appliance can be guaranteed.
Therefore the complete electrical installation is to be carried out by a licensed
company. Regulations such as VDE, ÖVE and other relevant standards are to be
observed. Before starting-up the appliance the owner has to provide a system
which is ready for operation (i.e. electrical wiring, a chimney which is available
and suitable, appropriate solid fuel).
Proper Operation
Attention should be paid to the fact that the appliance is not at all childproof
(doors, etc.) and therefore it must not be operated by children or other people
who are not authorized or trained. If the appliance is not installed properly and
if instructions (according to technical documentation, user manual) regarding
the starting-up and operation of the appliance are not followed, all warranty
claims will become null and void.
Chimmney requirements for heating systems
Prior to the first operation of the appliance the locally responsible chimney
sweep has to prove the suitability and readiness for operation of the new or
already existing chimney by a declaration of conformity. The owner has to en-
sure that the chimney is free from obstructions (no pluggings or coverings). Ad-
equate ventilation (sufficient fresh air) is necessary in the boiler room. Please
point out existing defects and /or alterations regarding the chimney and the
heating system. Due to low exhaust gas temperatures during changes in season
it is imperative that the chimney is tight and unsusceptible to moisture. Make
sure that flue and exhaust gas can escape to the outside.
Regular cleaning and maintenance of the appliance safety
instructions
Regular maintenance and care or cleaning of the stove, the heating gas draughts
and the connection piece as well as the chimney are particularly important for
the operational safety and efficiency of the stove. Please note the maintenance
and cleaning instruction in this user manual. You can also request the help of
your locally responsible chimney sweep to clean the fireplace. Only clean and
properly adjusted appliances work efficiently. Please note the correct sequence
of installation in this user manual.
Safety instuctions
When installing the stove, observe the regulations and provisions of the build-
ing authorities and fire police applicable at the place of installation. It is ab-
solutely necessary to consult your locally responsible chimney sweep and the
local building authority regarding questions of this nature.
•Please read the information in this manual carefully before you install or
start up your stove for the first time.
•If the instructions are not followed, this results in the immediate expiration
of our warranty obligations!
•Keep these instructions in a safe place. Should they be lost, we will be
happy to send you a new copy.You will find important information for your
safety, for the use, care and maintenance of the appliance, so that you can
enjoy your appliance for a long time. In case of queries please do not hesi-
tate to contact the technical customer service of LOHBERGER.
Before connecting the stove to the chimney, you should inform the locally respon-
sible chimney sweep.

page 5
85
4
14
30
60 59,5
2. Technical data2. Technical data
16
18
17
19
20
2122
1
6 5
2
3
4
9
11
14
10
12
13
15
8
7
9Protective grating
10 Pellet storage container
11 Door contact shifter
12 Drive shaft - rotary feeder
13 Driving chain-conveying unit
14 Auger motor
15 Grate - Motor
16 Flame temperature sensor
1Cover
2Control panel
3Sidewall built-in cupboard
4Base panel lateral
5Base panel front
6Front panel built-in cupboard
7Main plate
8Ash pan
17 Auger
18 Flame bruck
19 Extraction shaft
20 Burner brick
21 Grate unit
22 Exhaust fan

page 6
The pellet stove can be operated either with wood pellets or billet wood.
In addition to heating the room where the appliance is installed, the appliance
can also be used for cooking and baking when it is running on firewood. With
appliances featuring a central heating insert (type designation –Z, optional
equipment) hot water is also generated. The heat is transferred to the heating
system by this medium (reservoir, heating circuit, etc.). The cooking plate,
stove body, viewing window, etc. give off radiant heat.
For heating, switch the appliance on, it regulates either according to the pre-set
heating output when operating on pellets or according to the set temperature
of the boiler when operating appliances with central heating insert.
The set temperature of the boiler can be influenced by the setting summer
mode /winter mode. In addition, the output of the appliance can be affected
by setting the power levels. Once the boiler has achieved the preset tempera-
ture, the selected power level limits the upward adjustment range of the pellet
burner (for example this is necessary for cooking or baking). The switching on/
off process of the appliance can be automated through an integrated automatic
operation with a weekly operation schedule or by means of a remote control
unit.
Starting the appliance, irrespective of whether this is done manually or auto-
matically, the tilting grate is cleaned automatically. The pellets are transported
to the combustion chamber via the auger (with integrated rotary air lock as
back-burn protection) and subsequently electrically ignited. The auger auto-
matically supplies more pellets. The oxygen required for combustion flows in a
controlled way to the combustion chamber.
In the combustion chamber of the pellet module and in the subsequent firebox
of the stove the gases produced during combustion burn off – heat is radiated
via the exterior of the appliance as well as the heat exchanger surfaces. An ex-
tract fan, matching the amount of fuel and required combustion air, provides a
stable negative pressure in the boiler and consequently ensures that flue gases
escape through the chimney.
The pellet stove can be operated either with wood pellets or billet wood.
Operation with pellets
The operation with pellets is predominantly suitable for heating the room
where the appliance is installed. In this case the appliance is controlled by the
use of preset control variables. Cooking operation and oven operation is only
possible to a limited extent (the output can be increased by adding firewood).
Appliances equipped with a central heating insert (optional equipment) can
also generate hot water. The heat is transferred to the heating system (reser-
voir, heating circuit, etc.).
Operation with firewood
In addition to the operation with pellets, the appliance can also be convention-
ally heated with firewood. The basic functions of heating up and operating the
oven are comparable to that of a normal wood burning stove. The operation
with firewood is especially suitable for cooking and oven operation as well as
for heating the room where the appliance is installed.
It is also possible to automatically ignite the firewood by means of the pellet
burner. Just load the combustion chamber with firewood and turn on the pellet
burner.
If firewood is added to the combustion chamber while the stove is running on
pellets, the appliance recognises this and changes automatically to OPERATION
WITH FIREWOOD.
3. Types of operation3. Types of operation
4. Functional description4. Functional description
• Please note that with central heating appliances (type designation –Z) the
controlled operation of the boiler is only possible when burning pellets.
•When burning firewood, the appliance is also to be connected to the mains
supply to avoid damages to parts of the appliance.
•With pellet operation, the output for cooking and baking is only available
to a limited extent; the output can be increased by adding firewood.
• Please note that with central heating appliances (type designation –Z) the
controlled operation of the boiler is only possible when burning pellets.
•When burning firewood, the appliance is also to be connected to the mains
supply to avoid damages to parts of the appliance.
•With pellet operation, the output for cooking and baking is only available
to a limited extent; the output can be increased by adding firewood.
fig. 1
fig. 2

page 7
•In the event of a power failure, the chimney has to ensure the safe discharge
of the flue gases from the appliance. Consequently it performs an important
safety function and therefore several points are to be observed:
•It is obligatory to provide a connection to a chimney that is non-susceptible
to moisture and suitable for solid fuels.
•The chimney has to conform to the specifications given on the type plate and
in the user manual of the stove.
•Prior to installation it is necessary to perform a calculation of the chimney as
regards its dimensions.
•If the chimney draught is too high (>16 Pa) we recommend installing a damper
(draught regulator)
•Always connect the appliance to a separate chimney; no other heating appli-
ances should be connected to the same flue or chimney system.
•The flue pipe is to be connected to the chimney in compliance with the re-
quirements of the Building Regulations. For further questions please consult
your local chimney sweep.
•Make sure that all flue pipes are leak-proof. Your local chimney sweep will
be happy to give advice
6. Chimney connection6. Chimney connection
When installing dampers /draught regulators and explosion doors, please follow
the installation instructions of the local chimney sweep
When installing dampers /draught regulators and explosion doors, please follow
the installation instructions of the local chimney sweep
For dimensions and detailed information on the chimney connection please refer
to the operating manual of the stove.
For dimensions and detailed information on the chimney connection please refer
to the operating manual of the stove.
Suitable fuels
WOOD PELLETS
It is imperative that only wood pellets conforming to the Austrian standards
ÖNORM M7135 or DIN Plus are used. Diameter 6 mm, length max. 30 mm.
Storage of wood pellets
Pellets are supplied with a maximum water content of 10 %. Wood pellets must
not be exposed to humidity during transport, make sure that they are stored in
an absolutely dry place which is free of dirt.
WOOD
Billet wood (Fig. 2) should have a maximum water content of approximately
30 % of the dried weight, be approximately 1/3 m long and be chopped small.
In this way the billets are ignited rapidly, producing a better heat output than
larger wood billets for the same amount of wood. Undercover in the open, fir,
pine or alder wood should be stored a good 2 years, hard wood even 3 years.
The significance of the water content of wood on the calorific value is shown
in Table 1.
Unsuitable fuels
Moist wood, bark waste, sawdust, fine wood chips, brushwood, wood wool,
wood chips. Use only very small amounts of paper for lighting.
Burning such fuels generates high levels of pollutant emission, a lot of ash
while the calorific value is very low.
Impermissible fuels
Surface-treated wood (veneered, painted, impregnated, etc.), chipboard wood,
all types of waste (packaging waste), plastics, newspapers, rubber, leather,
textiles, etc.
Burning such materials will greatly pollute the environment and is prohibited
by the legislator. It can also damage the stove and chimney. Furthermore the
combustion of carbon energy is not allowed. The appliance has not been tested
for operating on these fuels; therefore damages to the appliance cannot be
ruled out and are not covered by warranty.
5. Fuels5. Fuels
Wood storage Water
content %
Calorific value
kWh/kg
Freshly cut from the forest 50 ~2,3
Stored over winter 40 ~2,7
Stored over summer 18-25 ~3,4
Air dry 15-20 ~4,2
fig. 1
fig. 2
table 1

A20
Wall opening to
be provided by
the customer
30
DN 100 DN 50
85
B* 15*
page 8
7. Requirements for the room where the appliance is situated7. Requirements for the room where the appliance is situated
Air supply connection from outside (optional equipment)
Gerät Seitenabstand
A
Bodenabstand
B
LCP 70 (F1+B1+P) 21 33
LCP 75 A (F1+B2+P) 21 33
LCP 75 B (F2+B1+P) 23,5 33
LCP 75 B-Z (F2+B1+P+Z) 23,5 19,5
LCP 80 (F2+B2+P) 23,5 33
LCP 80-Z (F2+B2+P+Z) 23,5 19,5
•… for an appliance height of 85
cm
Basically, the appliance is dependent on indoor air, that means the air sup-
ply needed for combustion is extracted from the room where the appliance is
positioned. Subsequently air supply is to be provided from outside by means
of a ventilation opening. To do this, an opening of 10-15 cm in diameter has to
be provided at one exterior wall of the room where the appliance is located.
Outside a stable protective grating is to be fitted. Furthermore, at places where
strong winds are prevalent or places which are exposed to weather, a protec-
tion against wind and rain is required.
If it is not possible to provide an opening to the outside from the room where
the appliance is positioned, it is also possible to create an opening in an ad-
joining room. Make sure that the adjoining room has a permanent connection
to the room where the pellet stove is positioned by means of a ventilation
grate.
If there are additional heating units in the same room, the ventilation openings
must provide adequate air supply for combustion to ensure proper operation
of all appliances!
Too low pressures in the room where the appliance is located (e.g. caused by
ventilation systems, extractor hoods etc.) or in the pellets container (e.g. caused
by pneumatic appliances) are likely to impair the functioning of the fire place and
their safety (technique) and are therefore not permitted.
Too low pressures in the room where the appliance is located (e.g. caused by
ventilation systems, extractor hoods etc.) or in the pellets container (e.g. caused
by pneumatic appliances) are likely to impair the functioning of the fire place and
their safety (technique) and are therefore not permitted.
Even with an outdoor air connection the requirements for an operation that is
independent from the ambient air are not fulfilled!
Even with an outdoor air connection the requirements for an operation that is
independent from the ambient air are not fulfilled!
•It is not allowed to install shut-off devices (flaps, dampers, …) in the air
supply line!
•The air supply line consisting of non-combustible materials must be a maxi-
mum of 4 m in length and must not have too many bends!
•To avoid condensation, the air supply line must be insulated!
•The air flue must be at least 50 or 100 mm, respectively, in diameter. If
rectangular tubes are used, they must maintain the appropriate diameter!
•If the air supply line runs directly to the outside, it has to be protected
against wind!
•The supply of external combustion air from above may only be provided by
means of chimney systems which have been approved by us..
•It is not allowed to install shut-off devices (flaps, dampers, …) in the air
supply line!
•The air supply line consisting of non-combustible materials must be a maxi-
mum of 4 m in length and must not have too many bends!
•To avoid condensation, the air supply line must be insulated!
•The air flue must be at least 50 or 100 mm, respectively, in diameter. If
rectangular tubes are used, they must maintain the appropriate diameter!
•If the air supply line runs directly to the outside, it has to be protected
against wind!
•The supply of external combustion air from above may only be provided by
means of chimney systems which have been approved by us..
For the technical acceptance of the heating system, the chimney sweep is required
to check the entire installation, in particular for sufficient combustion air supply.
For the technical acceptance of the heating system, the chimney sweep is required
to check the entire installation, in particular for sufficient combustion air supply.
fig. 4
Floor - load capacity
Prior to installing the appliance, make sure that the substruc-
ture of the floor is suitable to bear the weight of the appliance.
Ensure that the stove is positioned horizontally and without
vibration.
Room and ambient temperatures /humidity
The appliance is suitable for rooms with normal humidity and
room temperatures ranging from +5 °C to +20 °C. Should room
temperatures fall below 5 °C, it is imperative to add appropri-
ate antifreeze to the water.
The appliance is not splash proof; therefore it must not be
installed in wet rooms such as bathroom units.
Accessory:
Air supply connection
pellets module ø 50 mm Accessory:
Air supply connection stove ø 100
mm (see user manual stove)
fig. 3
To ensure a sufficient supply of combustion air in the case of tightly sealed
windows and low-energy houses equipped with ventilation systems or when
ducted extractor hoods are used, it may be necessary to provide fresh combus-
tion air from outside.
table 2
The dimensions for fitting are shown in „Figure 4“ as well as „Table 2“. Please
note the changes to the dimensions due to the adjustment of the height of the
appliance or of the stove frame.
8. Air supply connection from outside (accesory)8. Air supply connection from outside (accesory)

page 9
9. Heating connection9. Heating connection
10. Electrical connection10. Electrical connection
•When connecting the appliance by means of a plug to a socket, pay at-
tention to the appropriate polarity (if necessary use a mains plug with
an anti-twist protection) because the appliance must be connected in the
proper phase!
•An emergency power-off switch or an individual safety device is to be in-
stalled into the main distribution (for maintenance works, etc.
•It is imperative that electrical connections regarding the appliance are to
be carried out by a qualified professional in accordance with the applicable
technical regulations, especially the VDE- and OVE-regulations. We do not
accept liability for damages to the appliance as a result of inexpert connec-
tions and are subsequently excluded from warranty.
•All electrical connecting cables leading from and to the appliance must not
touch hot exterior surfaces of the appliance or of the chimney flue. The
cables must not be laid over sharp edges.
•When connecting the appliance by means of a plug to a socket, pay at-
tention to the appropriate polarity (if necessary use a mains plug with
an anti-twist protection) because the appliance must be connected in the
proper phase!
•An emergency power-off switch or an individual safety device is to be in-
stalled into the main distribution (for maintenance works, etc.
•It is imperative that electrical connections regarding the appliance are to
be carried out by a qualified professional in accordance with the applicable
technical regulations, especially the VDE- and OVE-regulations. We do not
accept liability for damages to the appliance as a result of inexpert connec-
tions and are subsequently excluded from warranty.
•All electrical connecting cables leading from and to the appliance must not
touch hot exterior surfaces of the appliance or of the chimney flue. The
cables must not be laid over sharp edges.
We strongly recommend the installation of a smoke detector or fire warning device
which interrupts the current supply of the appliance in case of an emergency! Objects
which have been left inadvertently on the cooking surface are likely to catch fire
in case of automatic starting-up of the pellet burner (e.g. with an automatic timing
device).
We strongly recommend the installation of a smoke detector or fire warning device
which interrupts the current supply of the appliance in case of an emergency! Objects
which have been left inadvertently on the cooking surface are likely to catch fire
in case of automatic starting-up of the pellet burner (e.g. with an automatic timing
device).
If possible the mains cable which is supplied with the appliance should be con-
nected to the power line prior to the installation of the appliance!
If possible the mains cable which is supplied with the appliance should be con-
nected to the power line prior to the installation of the appliance!
Output requirements for heating water
Heat requirement during operation must exceed 1,6 kW. If the heat output falls
below this value, the built-in safety devices will be activated and /or the appli-
ance will be shut down.
Return flow increase
The return flow temperature must be at least 55 °C at the return flow connect-
ing piece of the appliance (in the ideal case 60 °C), otherwise this will result in
the building-up of soot and tar and as a consequence in corrosion.
For dimensions and detailed information on the heating connection please refer to
the installation and operation instructions of your stove.
For dimensions and detailed information on the heating connection please refer to
the installation and operation instructions of your stove.
•The appliance has been exclusively designed to operate with an AC voltage
of 230 V /50 Hz.
• Voltage fluctuations ranging from –15 % up to +10 % are permissible.
•The connection is carried out by means of a 3-pole mains cable (to be sup-
plied with the appliance).
•Do not use sockets with power plugs without anti-twist safeguard as the ap-
pliance is dependent on the phase!
•It is imperative that you install a protective earth conductor!
•A 5 x 20 2,5 A T glass tube safety fuse serves as main fuse. The fuse is in-
stalled at the front wall of the built-in cupboard (inside).
•An emergency stop switch is to be installed by the owner (for maintenance
works, etc.).
Flue pipe connection right side:
Heating flow 1“
Heating return
flow 1“
61
53,5
29
65*
47,5*
4,8 inlet /outlet temperature
safety relief valve 1/2“
* for an appliance height of 85 cm!
connecting socket *
EMERGENCY OFF
smoke/re alarm
power line
STOVE PELLETS MODULE
* … for an appliance height of 85 cm
* for an appliance height of 85 cm!
Flue pipe connection left side:
Heating flow 1“
Heating return
flow 1“
46
53,5
29
65* 47,5*
4,8
inlet /outlet temperature
safety relief valve 1/2“
fig. 5
fig. 6
fig. 7

*
≥ 20
≥ 20
Fire protection unit
≥ 20
page 10
*... included in the scope of supply for the PELLETS MODULE!
The clearance for the integration in a built-in kitchen is to be calculated as
follows:
Examples of installations:
Exampel with LC 80
A + B + C + D
7,5 + 80 + 7,5 + 30
= 125 cm installation dimension
Distance fire protection A5-15 cm
+Basic width of appliance B70-80 cm
+Extra clearance for inspection C * 7,5 cm
+Width of pellets module D30 cm
=Installation dimension
Keep adequate distance from combustible items (wood panelling, furniture,
curtains, etc.) around the stove. The walls in the area of the stove must be
rendered fireproof extending up the full height of the walls and covering a
width of at least 50 cm to either side or to the front beyond the fireplace.
(Fig. 7).
The safety distance with items to be protected (e.g. combustible walls, walls
with combustible components, suspended kitchen cupboards and carrying
walls made of reinforced concrete) is at least 20 cm (Fig. 8).
Between the stove and the pellets module a fire protection sidewall has
already been provided. (Fig. 8).
When attached to combustible materials or installed in a built-in kitchen
or attachment to an electric stove or any other appliance, a fire protection
sidewall VBS (+5 cm or +7,5 cm, resp.) must be provided. (Fig. 9).
The maximum hight of the fixtures is up to the appliance height (standard
height 85 cm). Fixtures which are higher (f. e. tall cupboard) have to be at
least 20 cm from the pellets module away. (figure 9).
Overhead installations
Maintain a minimum distance of 75 cm and ensure adequate rear ventilation
for the suspension boxes to avoid heat being trapped. (Fig. 10).
Flue gas pipe
When installing the flue gas pipe, adhere to the following minimum distanc-
es to combustible building materials: wall distance 20 cm, ceiling distance
40 cm.
Floor plate
With a combustible floor (wood, plastic, wall to wall carpet,...) a floor plate
made of steel, copper or another noncombustible material must be used.
This surface must protrude the stove outline by at least 5 cm, on the operat-
ing side by at least 30 cm.
With this type of questions it is imperative to consult your responsible
chimney sweeper.
11. Fire prevention11. Fire prevention
12. Integration in built-in kitchen12. Integration in built-in kitchen
The Lohberger fire protection units VBS have only been tested in connection with
the Lohberger – stove series VARIOLINE (appliance type LM.., LC.., LCP.., …)!
The Lohberger fire protection units VBS have only been tested in connection with
the Lohberger – stove series VARIOLINE (appliance type LM.., LC.., LCP.., …)!
In the area of the pellets module the swivel range of the cover for adding fuel
must be taken into account! (Fig. 10)
In the area of the pellets module the swivel range of the cover for adding fuel
must be taken into account! (Fig. 10)
fig. 12
A + B + C + D
fig. 8
fig. 9
fig. 10
fig. 11
fig. 13
≥ 75 ca. 64
≥ 60

A
C1
G1
H1
J1
J8 pcs.
J2 A
J1
C
J1
G
page 11
13. Scope of supply13. Scope of supply
ABase (bottom)
C1 Sidewall preassembled
G1 Front panel preassembled
H1 Base cover front
JMounting accessories enamel covering
J1 Sheet metal screw 4,2 x 10 mm
14. Installing the panels14. Installing the panels
Base (bottom)
Place the base (A) in front of the appliance and push it from the front under
the pellets module. (Fig. 14).
The two supplied screws (J2) are to be attached to the appropriate drill-holes,
however, do not tighten them yet!
Side wall
Hook the sidewall (C1 / C2) into the appropriate openings at the base and fas-
ten it at the top with both supplied screws (J1). Use adjusting screws to level
out unevenness of the floor and distances in height (figure 15).
Connections main plate
Provide the connections at the main plate (see terminal connection diagram
on page 25).
Front panel
Connect the flat ribbon cable of the control panel at the main plate. Insert
the front wall (G) as illustrated and fasten it at the top with two screws (J1),
(figure. 16).
Adjust the completely assembled built-in cupboard at the stove front. Tighten
the screws which fasten the base! (figure 14)!
If necessary take out the adjustable foot of the stove a little to facilitate this
procedure!
If necessary take out the adjustable foot of the stove a little to facilitate this
procedure!
fig. 14
fig. 15
fig. 16
fig. 17
adjusting screw

Stove ON 13:45
Burner OFF
O u t p u t < ||||||||||||||||||||||||||||||- - - - >
OK
page 12
Button “ON / OFF“
To switch the appliance on and off in the top level.
Display (illuminated)
Display options top level:
•Appliance status
•Clock time
•Operating status
•Power level
•Button”LEFT“
•To reduce the output in the top
level.
•To switch from one adjustment
point to the previous in the ad-
justment levels
•To return by one menu level
each.
Button „RIGHT“
•To increase output in the top level.
•To switch from one adjustment point to the
next in all adjustment levels.
•BUTTON “UP“
•To select the desired menu item in all sub-levels
•To activate the key lock (only with activated key
lock function) by simultaneous pressing of the
buttons UP and DOWN in the top level
•To switch on the functions in the adjustment lev-
els
•To increase values in the adjustment levels
Stove o 13:45
Burner o
•Button „DOWN“
•To select the desired menu item in all sub-levels
•To activate the key lock (only with activated key
lock function) by simultaneous pressing of the
buttons UP and DOWN in the top level.
•To switch on the functions in the adjustment lev-
els.
•To reduce the values in the adjustment levels
Button „OK“
•To enter all sub-levels of the menu, starting
from the top level.
•To confirm the selected sub-levels of the
menu.
•To confirm the set values and to switch from
one adjustment point to the next in the ad-
justment levels
•To confirm error messages by pressing and
holding the button (approx. 2 seconds)
15. Operation / Settings15. Operation / Settings
16. Menu – Top level 16. Menu – Top level
In the top level of the menu (figure 18) the current appliance status is shown.
Furthermore basic operating functions such as switching the appliance on/off,
setting the heating output as well as activating the key lock are possible.
DISPLAY OPTIONS
Line 1 – Display of the current appliance status as well as of the current clock
time
Line 2 – Display of the respective operating status general notes and error
messages.
Line 3 – Display of the selected output level
LIGHTING
To switch on the display lighting press an operating button, after approx. 30
seconds the lighting is turned off again automatically.
Switching on the appliance
Press once in the top level of the menu. The display “STOVE ON” ap-
pears as well as the operating status BURNER ACTIVATION. The appliance
turns on.
Switching off the appliance
Press once in the top level of the menu. The display “STOVE OFF” ap-
pears as well as the operating status BURNER OFF. The appliance shuts down.
Setting the heating output
To lower the heating output, press in the top level of the menu.
To raise the heating output, press in the top level of the menu.
Adjustment range heating output:
3 – 10 for air heaters (P6)
5 – 10 for central heating appliances (P7, type-designation –Z)
fig. 18
fig. 19

-- Main menu --
>Settings <
Information
Factory level
-- Main menu --
>Settings <
Information
Default setting
-- Settings --
>Time/Date < |
Automatic mode |
Heating period |%
-- Settings --
>Time/Date < |
Automatic mode |
Heating period |%
-- Time/Date --
>Clock time 13:46 <
Date 04/09/2009
-- Time/date --
Time 13:46
>Date 04/09/2009 <
page 13
Key lock
To switch on the key lock, press the buttons and at the same time.
To switch off the key lock, press the buttons and at the same time.
The key lock prevents an accidental adjustment of the appliance settings (e.g.
when cleaning the control panel, caused by children, …) and can be switched on
or off if required
The key lock prevents an accidental adjustment of the appliance settings (e.g.
when cleaning the control panel, caused by children, …) and can be switched on
or off if required
The key lock function is switched off when the appliance is delivered and can be
activated in the menu Settings --> See point Key lock (function)
The key lock function is switched off when the appliance is delivered and can be
activated in the menu Settings --> See point Key lock (function)
If the key lock is activated, it is still active after a possible power failure.If the key lock is activated, it is still active after a possible power failure.
18. Main menu18. Main menu
To enter the main menu from the top level of the menu, press the >OK< button
once.
Settings To perform appliance settings
Information Display /Information on the appliance and its components
Default setting Detailed settings (service technician)
17. Menu Settings17. Menu Settings
To get to the menu Settings from the main menu, select the menu SETTINGS
with or and press the >OK< button once.
Time /Date: To set clock time and date
Automatic mode: To change between manual operation and operation with ad-
justable heating times.
Heating period: Adjustment level for heating times
Key lock: To switch the key lock on/off
Servicecode: To reset the cleaning /maintenance interval by the service tech-
nician
Reset: To reset all settings made by the customer.
For central heating appliances.
For central heating appliances:
Summer/Winter: To change from summer to winter mode
Time/Date
Select the menu Time/Date in the menu Settings with or and press the
OK button once (figure 22). Select sub-menu clock time by pressing the but-
tons or (figure 23).
Press OK button once, the display Hour flashes
Adjust accordingly by pressing the buttons or
Press OK button once, the set value is stored, the display Minute flashest
Adjust accordingly by pressing the buttons or .
Press OK button once, the set value is stored, the display day flashes
Adjust by pressing the buttons or
Press OK button once, the set value is stored
Select sub-menu date by pressing the buttons or (figure 24)
Press OK button once, the display Day flashes
fig. 20
fig. 21
fig. 22
fig. 23
fig. 24
fig. 25

-- Settings --
Time/date |
>Automatic mode < |
Heating period |%
-- Automatic mode --
>Auto OFF <
-- Automatic mode --
>Auto ON <
-- Settings --
Time/Date |
Automatic mode |
>Heating period < |%
-- Heating period --
>MO< WE FR Su
TU TH SA ALL
--Heating period MO--
>T1 10:30 - 13:00 <
T2 13:30 - 17:00
page 14
Adjust by pressing the buttons or
Press OK button once, the set value is stored and the display Year flashes
Press OK button once, the set value is stored
Press 3 times to return to the top level of the menu.
Automatic mode
Select the menu Automatic operation in the menu SETTINGS by pressing
or (Fig. 25)
Press OK
button once.
The setting can be changed by pressing the buttons or geändert
werden (Fig. 26/27).
Press the button 3 times to return to the top level of the menu.
Should the appliance be switched on or off by means of an external command, for
example by means of a room thermostat, a buffer thermostat etc., the AUTOMATIC
MODE can be changed to OFF or ON.
However, when switching AUTOMATIC MODE to ON, an external command will only
be taken into account within the pre-set heating times!
Should the appliance be switched on or off by means of an external command, for
example by means of a room thermostat, a buffer thermostat etc., the AUTOMATIC
MODE can be changed to OFF or ON.
However, when switching AUTOMATIC MODE to ON, an external command will only
be taken into account within the pre-set heating times!
The automatic operation determines whether the appliance is operated manually
(standard setting OFF) or whether the internal clock is used for switching the ap-
pliance on /off.
The automatic operation determines whether the appliance is operated manually
(standard setting OFF) or whether the internal clock is used for switching the ap-
pliance on /off.
Heating times
Select the menu Heating period in the menu Settings by pressing the buttons
or and press the OK once (figure 28).
Select weekday by pressing the buttons or and press OK
once
(figure 29).
Select heating time (T1 /T2) by pressing the buttons or (figure 30)
Press OK
button once, the display Turn-on time/hour flashes.
Adjust value by pressing the buttons or .
Press the OK button once, the set value is stored, the display Turn-on
time/minute flashes
Adjust value by pressing the buttons or .
Press OK
button once, the set value is stored, the display Turn-off
time/hour flashes.
--> For settings see turn-on time.
Press four times to return to the top level of the menu.
Here you can select two heating times each for each individual weekday
(MO, TU, WE …). If the same heating times shall apply for the whole week, two
heating times each can be selected with ALL.
CAUTION: The setting ALL will overwrite all settings of the individual weekdays!
Here you can select two heating times each for each individual weekday
(MO, TU, WE …). If the same heating times shall apply for the whole week, two
heating times each can be selected with ALL.
CAUTION: The setting ALL will overwrite all settings of the individual weekdays!
fig. 26
fig. 27
fig. 28
fig. 29
fig. 30
fig. 31

-- Settings --
Automatic mode |
Heating period |
>Keylock < |%
-- Keylock --
>Keylock OFF <
-- Keylock --
>Keylock ON <
-- Settings --
Keylock |
Service code |
>Reset < |%
-- Reset --
Reset with OK
-- Settings --
Heating period |
Keylock |
>Servicecode < |%
-- Servicecode --
>Servicecode **** <
-- Servicecode --
Code wrong
page 15
Key lock (function)
Select the menu Keylock in the menu Settings by pressing the buttons or
and press OK button once (figure 31).
The key lock function can be activated /deactivated by pressing the buttons
or (figure 32/33).
Press button 3 times to return to the top level of the menu.
Now the key lock can be activated or deactivated in the top level of the menu
by simultaneous pressing of the buttons and .
To use the key lock in the top level of the menu, the key lock function must be
activated. If the keylock function is switched on, the key lock will be automatically
activated after a power failure.
To use the key lock in the top level of the menu, the key lock function must be
activated. If the keylock function is switched on, the key lock will be automatically
activated after a power failure.
Service code
Select the menu Servicecode in the menu Settings by pressing the buttons
or and press OK button once (figure 34).
Press OK button once, the first digit flashes.
Adjust number by pressing the buttons or (figure 35).
Press OK button once, the next digit flashes.
After entering the last digit, press the OK button once, when the correct
service code has been entered, the message “CLEANING CONF.” or “MAIN
TENANCE CONF.” appears in the text box.
Press the OK button once, the service hour meter for the maintenance
interval will be reset (resetting not visible!).
If an incorrect service code is entered, the message CODE WRONG appears in
the text box (figure 36).
Press OK button once, repeat the steps for the entry of the service code
and enter the correct service code.
Press button twice to return to the top level of the menu
To confirm cleaning works or maintenance works that have been performed on the
appliance, a service code is to be entered. As a consequence the relevant internal
service hour meter will be reset.
•Cleaning works are necessary after 250 operating hours and this will be
indicated in the top level of the menu by the display “APPLIANCE CLEAN-
ING”, confirmation with cleaning code 1234
•Maintenance works are necessary after 2000 operating hours and this will
be shown in the top level of the menu by “APPLIANCE MAINTENANCE”, a
confirmation by a service technician is required.
To confirm cleaning works or maintenance works that have been performed on the
appliance, a service code is to be entered. As a consequence the relevant internal
service hour meter will be reset.
•Cleaning works are necessary after 250 operating hours and this will be
indicated in the top level of the menu by the display “APPLIANCE CLEAN-
ING”, confirmation with cleaning code 1234
•Maintenance works are necessary after 2000 operating hours and this will
be shown in the top level of the menu by “APPLIANCE MAINTENANCE”, a
confirmation by a service technician is required.
Reset
Select the menu RESET in the menu SETTINGS by pressing the buttons or
and press OK button once (figure 37).
Press OK button once, a reset will be carried out (figure 38).
The display returns to the menu Settings.
Press the button twice to return to the top level of the menu.
In case of a reset all customer specific settings such as heating times etc. will be
reset to default setting!
In case of a reset all customer specific settings such as heating times etc. will be
reset to default setting!
fig. 32
fig. 33
fig. 34
fig. 35
fig. 36
fig. 37
fig. 38
fig. 39

-- Settings --
Service code |%
Reset |
>Summer/Winter < |
-- Summer/Winter --
>Winter mode <
-- Summer/Winter --
>Summer mode <
-- Main menue --
Settings
>Informations <
Default setting
-- Informations --
>Sensors < |
Actuators |
System/SWVersion |%
-- Informations --
>Sensors < |
Actuators |
System/SWVersion |%
-- Sensors --
>Door cntact ON< |
Grate contact ON |
Release ON |%
-- Sensoren --
T Flame 38 |%
T Flue gas 26 |
>T Plug-in 24< |%
-- Sensors --
T Flue gas 26 |%
T Plug-in 24 |
>T Boiler 29< |
page 16
Summer/Winter (only for appliances with central heating insert)
Select the menu SUMMER/WINTER by pressing or and press the
OK button once (figure 38).
The setting can be changed by pressing the buttons or (figure 40/41).
Press button three times to return to the top level of the menu.
To reduce heat output in summer, the appliance can be changed from winter to
summer mode. This setting limits the upwards adjustment range of the pellet
burner.
• Boiler set-point temperature WINTER 75°C
• Boiler set-point temperature SUMMER 65°C
To reduce heat output in summer, the appliance can be changed from winter to
summer mode. This setting limits the upwards adjustment range of the pellet
burner.
• Boiler set-point temperature WINTER 75°C
• Boiler set-point temperature SUMMER 65°C
19. Menu Informations19. Menu Informations
To enter the menu Information from the main menu, select the menu Informa-
tion by pressing the button or and press the OK once (figure 42).
Sensors Passive appliance components such as sensors, …
Actuators Active appliance components such as motors, blowers, …
Appliance / SW
Version
Display of the pre-set appliance type and of the installed
software version.
Operating hours Display of the total amount of operating hours as well as
how many operating hours are left until the next mainte-
nance of the appliance is due.
Sensors
Select the menu Sensors in the menu Information by pressing the button
or and press the OK once (figure 44)
Paging through the menu items is possible by pressing the button or
(figure 45-47).
ON /OFF (OFF = door open)
ON /OFF (OFF = grate open)
ON /OFF (OFF = no external command)
Current flame temperature
Current exhaust gas temperature
Current discharge chute temperature
Current boiler temperature – (only for appliances with central heating insert)
Press three times to return to the top level of the menu.
fig. 40
fig. 41
fig. 42
fig. 43
fig. 44
fig. 45
fig. 46
fig. 47
fig. 48

-- Informations --
Sensors |
>Actuators < |
System/SWVersion |%
-- Actuators --
>Plug-in OFF < |
Clocking 0 |
Fan OFF |%
-- Actuators --
Speed 0 |
Grate motor OFF |
>Ignition OFF< |%
-- Actuators --
Grate motor OFF |
Ignition OFF |
>Pump OFF< |%
-- Informations --
Sensors |
Actuators |
System/SWVersion |%
-- System/SWVersion --
P7/LCP75B/LCP80N
SWVersionA 8.27
SWVersionD 1. 6
-- Informations --
Actuators |
System/SWVersion |
>Operating hours < |%
-- Operating hours --
Total 0
Until maint. 2000
page 17
Actuators
Select the menu Actuators in the menu Information by pressing the button
or and press the OK once (figure 48).
Paging through the menu items is possible by means of pressing the button
or (figure 49-51).
ON /OFF (OFF = Auger off)
Current value
ON /OFF (OFF = Blower off)
Current value
ON /OFF (OFF = Motor off )
ON /OFF (OFF = Ignition off)
ON /OFF (OFF = Pump off) – (only for appliances with central heating insert)
Press button three times to return to the top level of the menu.
System/SW Version
Select the menu System /SW Version in the menu Information by pressing the
button or and press the OK
once (figure 52).
System type
Software version main circuit board
Software version control panel
Press three times to return to the top level of the menu.
Operating hours
Select the menu Operating hours in the menu Information by pressing the but-
ton or and press the OK once (figure 54).
Display of the Operating hours
Display Operating hours until next maintenance of the appliance
Press three times to return to the top level of the menu.
fig. 49
fig. 50
fig. 51
fig. 52
fig. 53
fig. 54
fig. 55
fig. 56

Stove ON 13:45
Burner start-up
O u t p u t < ||||||||||||||||||||||||||||||- - - - >
Stove ON 13:45
Burner ON
O u t p u t < ||||||||||||||||||||||||||||||- - - - >
page 18
General note – Surfaces
Only high-quality air-drying varnish is used which does not smell nor give off
fumes when heated up for the first time if it is allowed to dry completely (at
room temperature). If the appliance is heated up shortly before the varnish has
hardened, an unpleasant smell and fume will be temporarily produced. Please
give the room where the appliance is located a good airing.
Charging the storage container
Make sure that you use approved pellets which conform to ÖNORM M7135/DIN
51731 – see imprint on the pellets bags or consult your pellets supplier. Open
the container lid. To avoid raising of dust, pour pellets slowly and not from too
high a position. After feeding the pellets, the lid is to be closed and should
remain closed during operation.
20. Operating the stove for the first time20. Operating the stove for the first time
•Do not leave small children unattended in the vicinity of the stove: the
heating system is not childproof!
•Prior to the first start-up all connections (chimney flue connection, power
supply, etc.) are to be checked.
•The viewing glass as well as the door become very hot when the stove is in
use (temperatures up to 300 °C). Pay attention to the fact that these parts
must not be touched when the stove is in operation.
•Keep the firebox door closed at all times, even if the stove is not in use.
•Make sure that no objects are in the combustion chamber, in the firebox as
well as in the oven.
•Only after the installation is completed in accordance with the user manual
and installation instructions, is it allowed to charge the storage container
with pellets (at least 5 kg).
•Do not leave small children unattended in the vicinity of the stove: the
heating system is not childproof!
•Prior to the first start-up all connections (chimney flue connection, power
supply, etc.) are to be checked.
•The viewing glass as well as the door become very hot when the stove is in
use (temperatures up to 300 °C). Pay attention to the fact that these parts
must not be touched when the stove is in operation.
•Keep the firebox door closed at all times, even if the stove is not in use.
•Make sure that no objects are in the combustion chamber, in the firebox as
well as in the oven.
•Only after the installation is completed in accordance with the user manual
and installation instructions, is it allowed to charge the storage container
with pellets (at least 5 kg).
The regulation is determined by the specified boiler set-point temperature
(75°C or 65°C respectively, see setting SUMMER /WINTER).
Should the boiler set-point temperature be exceeded by 10°C, the appliance
shuts down automatically display burner OFF and switches on again once the
boiler set-point temperature has fallen below the value by 3 °C.
21. Heating operation with pellets21. Heating operation with pellets
•While the appliance operates on pellets, the damper (start-up flap) (see
instruction manual stove) must not be opened!
•Set both stove air regulators to level “0”!
•While the appliance operates on pellets, the damper (start-up flap) (see
instruction manual stove) must not be opened!
•Set both stove air regulators to level “0”!
The appliance might resume operation automatically at any time, therefore please
note the information in point External Release /Remote control unit!
The appliance might resume operation automatically at any time, therefore please
note the information in point External Release /Remote control unit!
Switching the appliance on
Press the button once in the top level of the menu.
The display STOVE ON appears as well as the operating status burner start-up
(figure 56).
The appliance switches on.
Setting the heating output
Setting of the heating output in the top level of the menu (figure 57).
Reduce heating output by pressing the button .
Increase heating output by pressing the button .
Adjustment range heating output:
3 - 10 for air heaters (P6)
5 - 10 for central heating appliances (P7, type designation -Z)
If the heating output is not sufficient although it has been set at the highest
level, the temperature can be increased by loading firewood.
fig. 57
fig. 58

Stove OFF 13:45
Firewood operation
O u t p u t < ||||||||||||||||||||||||||||||- - - - >
Stove OFF 13:45
Burner OFF
O u t p u t < ||||||||||||||||||||||||||||||- - - - >
Stove OFF 13:45
Burner activation
O u t p u t < ||||||||||||||||||||||||||||||- - - - >
Stove OFF 13:45
Firewood operation
O u t p u t < ||||||||||||||||||||||||||||||- - - - >
page 19
22. Heating operation with firewood22. Heating operation with firewood
Ignition of firewood by means of pellet burner
Press the button once in the top level of the menu.
The display STOVE ON as well as the operating status BURNER ACTIVATION
appears (figure 59).
Because of the increased output caused by the burning of firewood, the pellet
burner switches to operation with firewood, the display shows the operating
status FIREWOOD OPERATION (figure 60).
Should no further increase in the output be identified while the stove is operat-
ing on firewood, the appliance automatically returns to Operation with pellets
if the appliance is switched ON.
If the stove continues to burn firewood, the pellet burner shuts down auto-
matically. If no more firewood is added, the appliance changes after a safety
period automatically to heating operation with pellets according to the pre-set
heating output.
Adding of firewood during heating operation with pellets
If the stove is loaded with more firewood while the appliance is being heated
with pellets, the appliance first switches to operation with firewood.
The display STOVE ON as well as the operating status FIREWOOD OPERA
TION appears (figure 61).
If the stove continues to burn firewood, the pellet burner shuts down automati-
cally. If no more firewood is added, the appliance changes after a safety period
automatically to heating operation with pellets with the pre-set heating output.
•Do not open the damper (start-up flap)!
•If the firewood continues to burn for an extended period, set the regulators
for primary air (bottom) and secondary air (top) according to the enclosed
operating instructions of the stove.
•Open heating door, place 2 or three small pieces of firewood (beech wood)
onto the grate (1.6 kg to 2 kg according to the operating instructions of
the stove)
•Close heating door.
•Do not open the damper (start-up flap)!
•If the firewood continues to burn for an extended period, set the regulators
for primary air (bottom) and secondary air (top) according to the enclosed
operating instructions of the stove.
•Open heating door, place 2 or three small pieces of firewood (beech wood)
onto the grate (1.6 kg to 2 kg according to the operating instructions of
the stove)
•Close heating door.
Ignition of firewood manually operated
The display still shows STOVE OFF or BURNER OFF (figure 58).
•Set the regulator for primary air (bottom) to level 3 and set the regulator
for secondary air to level 6.
•Open heating door, load 2 to 3 small pieces of firewood or wood-shavings
onto the grate.
•Place 2 to 3 small logs on top of them and light them.
•Close heating door, leave the ash door just a crack open and allow the fire
to burn brightly
•Pull damper (start-up flap) handle (see instruction manual stove).
•Set the regulator for primary air (bottom) to level 3 and set the regulator
for secondary air to level 6.
•Open heating door, load 2 to 3 small pieces of firewood or wood-shavings
onto the grate.
•Place 2 to 3 small logs on top of them and light them.
•Close heating door, leave the ash door just a crack open and allow the fire
to burn brightly
•Pull damper (start-up flap) handle (see instruction manual stove).
Close ash door and damper (start-up flap) after the preheating phase is complete.Close ash door and damper (start-up flap) after the preheating phase is complete.
If the firewood continues to burn for an extended period, set the regulator for
primary air (bottom) to level 3 and the regulator for secondary air (top) to level 6.
If the firewood continues to burn for an extended period, set the regulator for
primary air (bottom) to level 3 and the regulator for secondary air (top) to level 6.
In the event that the appliance is operated with a low heating output, it may oc-
cur that the operation with firewood will not be immediately identified, thus the
ignition!
In the event that the appliance is operated with a low heating output, it may oc-
cur that the operation with firewood will not be immediately identified, thus the
ignition!
CAUTION: During operation with firewood, there is no automatic adjustment of the
output through the pellet stove control. The adjustment of the output depends on
the amount of fuel added. With appliances featuring a central heating insert, only
the heating circuit pump (provided by the customer) is switched on or off.
CAUTION: During operation with firewood, there is no automatic adjustment of the
output through the pellet stove control. The adjustment of the output depends on
the amount of fuel added. With appliances featuring a central heating insert, only
the heating circuit pump (provided by the customer) is switched on or off.
fig. 59
fig. 60
fig. 62
fig. 61

Stove OFF 13:45
Burner OFF
O u t p u t < ||||||||||||||||||||||||||||||- - - - >
Stove ON 13:45
APPLAINCE CLEANING
O u t p u t < ||||||||||||||||||||||||||||||- - - - >
Stove ON 13:45
SPECIAL CLEANING
O u t p u t < ||||||||||||||||||||||||||||||- - - - >
Stove ON 13:45
APPLIANCE MAINTENANCE
O u t p u t < ||||||||||||||||||||||||||||||- - - - >
page 20
23. External Release / Remote control unit (provided by the customer)23. External Release / Remote control unit (provided by the customer)
Press the button once in the top level of the menu.
The display STOVE OFF as well as the operating status BURNER OFF appears
(figure 62).
The appliance shuts down.
It is also possible to switch the pellet burner on or off by means of a remote
control unit. The burner is released through a make contact on the main circuit
board. Without a remote control unit this contact must be bridged (condition
as supplied to the customer).
Instead of the bridge, the remote control unit is to be connected to the main
circuit board. No additional software activation is necessary.
For the operation with a remote control unit the burner needs to be activated,
in the menu top level “STOVE ON” must appear.
If the remote control unit switches on, the burner starts up with the appropriate
ignition programme, depending on the flame temperature.
Should the remote control unit shut down, the burner switches off automati-
cally after a delay time of 5 minutes and waits for the next command by the
remote control unit.
The appliance must be switched on (Stove oN) and the desired heating output
is to be pre-set.
•If the remote control unit switches off, the burner continues to run for ap-
prox. 5 minutes
The appliance must be switched on (Stove oN) and the desired heating output
is to be pre-set.
•If the remote control unit switches off, the burner continues to run for ap-
prox. 5 minutes
Care should be taken as the appliance might
switch on automatically at any time!
Objects that have been inadvertently placed on the
cooking surface could ignite if the pellet burner
starts up automatically (e.g. start-up according to a
pre-programmed time, …) and start a fire.
Therefore we recommend installing a smoke or fire
detector that makes a warning sound in case of
emergency and interrupts the power supply of the
appliance!
Care should be taken as the appliance might
switch on automatically at any time!
Objects that have been inadvertently placed on the
cooking surface could ignite if the pellet burner
starts up automatically (e.g. start-up according to a
pre-programmed time, …) and start a fire.
Therefore we recommend installing a smoke or fire
detector that makes a warning sound in case of
emergency and interrupts the power supply of the
appliance!
24. Switching the appliance off24. Switching the appliance off
25. Display Maintenance / Cleaning25. Display Maintenance / Cleaning
Display Cleaning
The display APPLIANCE CLEANING appears after 250 operating hours (fig-
ure 63). After the cleaning work has been performed, the display will be reset
through the service code CLEANING and a new cleaning interval begins.
For details how to reset the service code, please refer to the point service code
on page 15.
Display special cleaning
The display Special cleaning appears after several errors in succession such
as NO PELLETS, NOT IGNITED or FILLING DOOR OPEN have occurred
(figure 64). The key lock will be activated automatically.
This display indicates a possible problem caused by dust or dirt that has ac-
cumulated in the appliance. Remove deposits from the appliance, in particular
from the pellet burner block by means of the provided cleaning brush. Subse-
quently release key lock, the displayed message will be cleared if you press and
hold the OK button for two seconds.
Display maintenance
The display APPLIANCE MAINTENANCE appears after 2,000 operating hours.
A comprehensive maintenance of the appliance is necessary (figure 65).
The maintenance works are to be carried out by a trained service technician.
Please get in touch with your local dealer. This maintenance ensures that all
installed components are checked for their good performance. Once the main-
tenance works have been completed, the display will be reset by the service
technician with the servicecode MAINTENANCE, a new maintenance interval
begins.
We offer you the possibility to conclude a yearly maintenance contract. If you wish
to take advantage of this service, please do not hesitate to contact the customer
service department of LOHBERGER®.
We offer you the possibility to conclude a yearly maintenance contract. If you wish
to take advantage of this service, please do not hesitate to contact the customer
service department of LOHBERGER®.
fig. 63
fig. 64
fig. 66
fig. 65
fig. 68
fig. 69
fig. 70