Lorell LLR03186 User manual


INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Mount, Dual Monitor, Space Saver
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
LLR03186

LLR03186 Installation Instructions
2
DISCLAIMER
Lorell and its affiliated corporations and subsidiaries
(collectively “Lorell”), intend to make this manual accurate and
complete. However, Lorell makes no claim that the information
contained herein covers all details, conditions or variations, nor
does it provide for every possible contingency in connection
with the installation or use of this product. The information
contained in this document is subject to change without notice
or obligation of any kind. Lorell makes no representation of
warranty, expressed or implied, regarding the information
contained herein. Lorell assumes no responsibility for accuracy,
completeness or sufficiency of the information contained in this
document.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Lorell product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Lorell
product which is attached to a primary Lorell product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all mounting systems
are properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this mounting system can result in serious personal injury
or damage to equipment! It is the installer’s responsibility to
make sure the structure to which this mounting system is
attached can support five times the combined weight of all
equipment. Reinforce the structure as required before
installing the mounting system.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components and accessories attached to the LLR03186
Dual Monitor mount and the desk up to (and including) the
display does not exceed the weight limits listed in the table
below. Use with products heavier than the maximum weight
indicated may result in collapse of the mount and its
accessories causing possible injury.
--SAVE THESE INSTRUCTIONS!--
MODEL Max Weight
Allowed for EACH
Display
Max Weight
Capacity of Mount
LLR03186 25 lbs
(11.3 kg)
50 lbs
(22.7 kg)

Installation Instructions LLR03186
3
DIMENSIONS
DESKTOP THICKNESS
RANGE
2.43
.43
61.8
11.0
DYNAMIC HEIGHT
ADJUST RANGE
18.81
5.81
477.8
147.6
INTERFACE
ROTATION
RANGE
90
MOUNTING PATTERN
COMPATIBILITY
100 X 100
75 X 75
UP
10
DOWN
DIMENSIONS: INCHES
[MILLIMETERS]

LLR03186 Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité

Installation Instructions LLR03186
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
3/16” (included)
1/8” (included)
A (1)
[Desk clamp arm]
B (8)
M4x10mm C (8)
M4x20mm
D (8)
M10x5.3x10 3/16”
1/8”
K (1)
L (1)
E (1)
[Clamp bracket] F (1)
5/16-18”
G (1)
5/16-18 x 6”
H (2)
#10-32-3/8”
J (2)
M4x4mm

LLR03186 Installation Instructions
6
Assembly And Installation
Connecting Desk Clamp Arms to Desk
Standard Installation
1. Loosen clamp screw until enough space is created between
clamp and mount to allow for desk mounting. (See Figure 1)
NOTE: If space is limited behind desk (i.e. against wall, etc.),
remove lower piece of clamp and two screws holding it
to the mount and reattach parts prior to Step 3! (See
Figure 2)
2. Place mount (A) on top of desk at desired mounting
location. (See Figure 1)
3. Tighten clamp using clamp screw until mount is securely
fastened to desk. (See Figure 1)
Figure 1
Figure 2
Grommet Hole Option
NOTE: The clamp mounts may be installed directly to grommet
holes between 1 1/4” and 2 1/2” in diameter. If grommet
hardware (E-G) is used, they can be installed to
grommet holes between 3/8” and 2 1/2” in diameter.
Direct Installation
1. Remove lower piece of clamp from assembly by removing
two button head cap screws holding piece to assembly.
(See Figure 3)
2. Install remaining part of clamp through grommet hole. (See
Figure 3)
Figure 3
3. Reattach removed piece of clamp and screws to assembly.
(See Figure 4)
4. Tighten clamp using clamp screw until mount is securely
fastened to desk. (See Figure 4)
Figure 4
1
23
desk
top view
(A)
2
x 2
1
x 2
3

Installation Instructions LLR03186
7
Using Grommet Hardware
1. Remove desk clamp from mount by loosening button head
cap screw until clamp is completely disengaged from the
bolt. (See Figure 5)
2. Maneuver clamp so that it is totally removed from desk
mount. (See Figure 5)
NOTE: Set removed washers aside for re-use.
Figure 5
3. Locate a flat surface (thickness of 3/4” minimum to 3 1/2”
maximum) on which to mount the desk mount plate.
4. If mounting hole does not already exist on desk, drill 3/8”
mounting hole in desk at desired mounting location.
IMPORTANT ! : Mounting hole must be between 3/8”
and 2 1/2” in diameter!
5. Place mount on desk over grommet hole. (See Figure 6)
6. Use 5/16-18 x 6” button head cap screw (G), removed
washers, clamp bracket (E) and 5/16-18” square nut (F) to
secure mount to desk. (See Figure 6)
Figure 6
Display Installation - Standard Faceplate
1. Remove quick release faceplate from mount by pulling
quick release lever and sliding faceplate off mount. (See
Figure 7)
Figure 7
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components and accessories attached to the LLR03186
Monitor Arm up to (and including) the display does not
exceed 25 lbs (11.34 kg) per display or 50 lbs (22.68 kg) total.
2. Carefully place display face down on protective surface.
3. Connect faceplate to display
For flush mounting hole installation:
• Using Phillips screwdriver, carefully install four
M4x10mm screws (B) through corresponding
holes on faceplate and into the mounting holes on
the display. (See Figure 8)
Figure 8
2
1
removed
washers
(E)
(F)
(G)
6
removed washers
quick release lever
1
1
(for flush mounting holes)
(B) x 4
quick release
faceplate
3

LLR03186 Installation Instructions
8
For recessed mounting hole installation:
• Place four spacers (D) on top of mounting holes
on back of display. (See Figure 9)
• Using Phillips screwdriver, carefully install four
M4x20mm screws (C) through corresponding
holes on faceplate, spacers (D) and into the
mounting holes on the display. (See Figure 9)
Figure 9
4. Position display with faceplate attached above mount. (See
Figure 10)
5. Slide faceplate onto mounting head until quick release tab
clicks into place. (See Figure 10)
Figure 10
Adjustments
Low Profile Adjustment
1. Adjust inside arm to achieve desired low profile depth. (See
Figure 11) and (See Figure 12)
2. Use 1/8" hex key (L) to adjust low profile tension screws to
change tension. (See Figure 11) and (See Figure 12)
IMPORTANT ! : Only adjust small set screws on arms!
Large screws are the screws that hold arms together.
(See Figure 11)
Figure 11
Figure 12
(for recessed mounting holes)
(C) x 4
(D) x 4
quick release
faceplate
3
5
tension adjustment
set screws
1/8"
If space is limited in the back
If space is limited in the front

Installation Instructions LLR03186
9
Pitch Adjustment
1. Adjust pitch to desired tilt position. (See Figure 13)
2. Adjust pitch tension screw to change the adjustment
tension. (See Figure 13)
Pivot Adjustment
3. Adjust pivot position as desired. (See Figure 13)
4. Use 3/16” hex key (K) to adjust pivot point tension screws to
change pivot adjustment tension. (See Figure 13)
Figure 13
Rotational Adjustment
NOTE: (Optional) Rotational adjustment may be locked by
installing rotational locking screw (J) into back of
faceplate. (See Figure 14)
Figure 14
5. The monitor may be adjusted 90 degrees in either direction
in order to provide a portrait view of the monitor. (See Figure
13)
6. Use a Phillips screwdriver to adjust rotational adjustment
screw to adjust rotational tension. (See Figure 13)
Lift Arm Tension Adjustment
1. Tension may be adjusted with tension adjustment screw
inside cable management cover and 1/8” hex key (L). (See
Figure 15)
Figure 15
Display Removal
WARNING: Only remove display from mount when the
display can be lifted up from the mount! DO NOT remove
display unless the display is in the upright position! (See
Figure 16)
1. Make sure display is in the upright position.
2. Remove quick release faceplate from mount by pulling
quick release lever and sliding faceplate off mount. (See
Figure 16)
Figure 16
pitch
pivot point
tension
tension
5
1
3
Rotational tension
6
(J)
Reduce tension
Increase tension
(lighter display)
(heavier display)
Do NOT over-tension
adjustment tension
screw.
NOTE: Lift arm
must be at highest
height to access the
lift arm tension
adjustment screw
through the access hole.
quick release tab
2

LLR03186 Installation Instructions
10
Display Removal Security Screw
NOTE: In order to prevent display from being easily removed
from mount using the quick release lever, install
M4x4mm security screw (H) into lower hole on back of
faceplate. (See Figure 17)
Figure 17
Pivot Adjustment Range
1. Adjust arm angles as desired within a 90 degree range from
the pivot point of the arm and a perpendicular centerline of
mount. (See Figure 18)
WARNING: Swinging the arm beyond this range may result
in the mount slipping of the desk causing serious injury!
Figure 18
Cable Management
1. Press insides of cable management covers at both ends to
unhinge tabs on either end of cable management cover on
upper arm. (See Figure 19)
2. Lift cable management cover up until tabs are unhinged and
cover is in the “open” position. (See Figure 19)
Figure 19
Figure 20
3. Route cables through cable management channel on upper
arm. (See Figure 20)
IMPORTANT ! : Be sure to leave enough slack in the
cables near display and arm joint to allow for full arm
articulation!
4. Close cable management covers on monitor arm. (See
Figure 20)
5. Route cables through cable clips on lower arm(s). (See
Figure 20)
(M)
perpendicular centerline
90 degrees range
of motion per arm
pivot point of the arm
(top view)
cable management cover tabs
1
2
5
4
3
3
cable (typical)
2
5

Installation Instructions LLR03186
11

LLR03186 Installation Instructions
8800-003257 Rev00
01/2021