Lori Greiner Gold & Silver Safekeeper User manual

Gold & Silver SafekeeperTM Dressing Mirror
Jewelry Cabinet by Lori Greiner
Congratulations – you have just received a wonderful Dressing Mirror Jewelry Storage Cabinet
that not only will store and display your jewelry items efficiently, but will keep them from
tarnishing for 25 years or more.
Carefully unpack the box to find the following assembly pieces. There is a limited amount of
assembly required. The screw driving wrench included will be the only tool required. We
recommend that you assemble the Dressing Mirror Jewelry Cabinet Stand close to the location
you will be using it. Note: the screws, pegs, wrench, and key are packed inside the cabinet.
Locate the following pieces:
•1 Mirrored Cabinet (A)
•2 Side Legs (B)
•1 Leg Cross Piece Rod (C)
•Screw Wrench (D)
•2 Long Rod Screws (E)
•2 Loop Ended Screw Sets (F)
•2 Wood Pegs (G)
•1 Door Key (H)
•4 Cross Piece Screws (I)
•Leg Cross Piece Board (J)
By referencing the attached diagram sheet and following the assembly instructions below, you will
be able to set up your Dressing Mirror Jewelry Cabinet in a matter of minutes. NOTE: to avoid
damage during assembly, lock the Mirrored Cabinet Door shut so that it does not swing open
during set up.
Step 1 – Assemble Side Leg Stand:
Place Leg Cross Piece Rod (C) into one of the recessed holes on the inside of one of the Side Legs (B) and attach
with one Screw (E). Attach second Side Leg (B) by repeating above steps. Add Leg Cross Piece Board (J) by
holding between Side Legs and attaching with 4 Cross Piece Screws (I). Place one Wood Peg (G) into the
Adjustment Hole drilled on the inner side of each Side Leg. Pick any hole at this time and see below regarding
viewing angle adjustment.
Step 2 – Attach Mirrored Cabinet to the Side Leg Stand:
First, lay the Mirrored Cabinet (A) on a soft surface (such as carpet), mirror side down. Second, take the Side Leg
Stand and lay it down with the Mirrored Chest (A) between the two Side Legs, lining up the holes at the top of the
Legs with the screw holes in the side of the Mirrored Chest (A) so that the longer part of the Mirrored Chest is
positioned between the Side Legs. Third, take one of the Loop Ended Screw Sets (F) and place the 2 washers
between the Side Leg and the Mirrored Chest, holding so that you can push the Loop Ended Screw through the
Side Leg hole, the Washers, and into the screw hole on the Mirrored Chest (A). Screw in the Loop Ended Screw
until it is tight and Washers are gently squeezed between the Leg and Chest. Attach second Loop Ended Screw
and washer set to the other side of the Mirrored Chest in the same manner.
Step 3 – Stand the fully assembled Mirrored Cabinet upright:
While supporting the Mirror Chest door so that it does not open, carefully lift the Mirrored Cabinet upright
Step 4 – Adjust the Mirrored Cabinet viewing angle:
By tilting the Mirrored Chest back and forth, find the best angle for your height. While holding the Mirrored Chest
in this position, place one of the 2 Wood Pegs (G) into the hole that is closest to the back of the Chest. This Wood
Peg (G) will hold the Mirrored Chest at the proper angle. You can adjust at anytime, by repositioning the Wood
Peg (G) Insert Key (H) to lock and unlock.

The Gold & Silver SafekeeperTM Dressing Mirror Jewelry Cabinet is designed to prevent tarnishing
of your silver jewelry for over 25 years, while providing convenient, organized storage for all your
jewelry items. It will preserve your polished silver and keep it shiny, but will not transform a
tarnished piece to become shiny. It is also safe for all your jewelry, gold, pearls, gemstones and
costume!
Note: To start off right, polish your silver jewelry before placing into the Gold & Silver
SafekeeperTM Dressing Mirror Jewelry Cabinet. We recommend using a silver polishing cloth to
clean your tarnished jewelry. If using a liquid cleaner to clean your silver jewelry, make sure it is
thoroughly rinsed and free of all chemicals before placing in the jewelry box.
Storage sections and their uses:
+ The Earring Bars are meant for hanging both your pierced earrings (simply place earring post into
the slots on the cross bar and then tighten the earring back) and your clip-on earrings (simply clip
the earring onto the cross bar). Be careful not to put too much pressure on the Earring Bars when
placing your earrings on and off.
+ Under the Earring Bars, you will find Bracelet Hooks and a Bracelet Cross Bar. Hang your chain
style bracelets on the Hooks and place your cuff style bracelets onto the Cross Bar.
+ At the bottom of the door, you will find Necklace Hooks for hanging your necklaces upon.
+ At the top of the inner cabinet you will find a large Ring Pad area with slits aligned horizontally
across the whole pad. Simply press your rings into the slits. The foam core will hold your rings
safely in place.
+ Below the Ring Pad area you will find another Necklace Hook area for hanging more necklaces
upon.
+ Finally, there are numerous storage shelves on the lower half of the inner cabinet. These shelves
can be used for items that do not fit into the other specialize portions of the cabinet.
REMEMBER: Always keep your Silver SafekeeperTM Dressing Mirror Jewelry Cabinet closed
when not in use, for the anti-tarnish properties to work.
Enjoy!
Note: upon first opening your jewelry cabinet, you may notice an odor, which is part of the lacquer and
finishing process of the box. This odor is normal and will dissipate in time.
For questions or comments write: FYEO, Inc. P.O. Box 385, Winnetka, IL 60093
Fabric made in the USA, jewelry cabinet made in China.
PATENTED, INTERNATIONALLY PATENTED, and PATENT PENDING