Lotus Prio Series User manual

Mounting and User Instructions
Lotus-Prio Series Stoves
(Lotus Prio 1, Prio 2, Prio 3, and Prio 4, Prio 5, Prio 6)
Version 1, 10/4-2005

Introduction
Congratulations on your new Lotus Wood Stove
We sincerely trust that your Lotus Wood Stove will bring many happy hours
for you. However, to benefit fully from your investment, you should read these
instructions thoroughly. They contain some specific advice on how to benefit
fully from your stove – now, and in the years ahead. So, like all other directions
for use, keeping them in a safe place would be a good idea.
Lotus Wood Stoves are based on a long tradition; the first productions were
way back in 1979. Our production is now run in Langeskov on Funen in
Denmark, and is exported to a great many European markets. Our stoves are
produced to sound Danish tradition, and have given their owners good and
reliable service for years. So, once again, congratulations on your new Lotus
wood stove. We feel certain that putting your Lotus wood stove in operation
will inaugurate a warm and cosy beginning of a new home life for you.
The stove is intended for ”intermittent combustion”, a process achieved by
following the instructions of the guide below under “Use of Stove”
Mounting of Stove
Before your new stove will be ready to exude warmth and cosiness, you should
read these pages thoroughly. Pages reviewing the requirements for the
mounting and for the surroundings. Reference is also made to the fact that local
regulations, including those referring to national and European standards,
applying at all times must be met for the installation of your wood stove.
A warning should also be issued against any unauthorized change of your wood
stove. It should be added that the surfaces of your wood stove will become hot.
Lotus recommends that your stove be mounted by an authorized Lotus
distributor or by a fireplace service man recommended by an authorized Lotus
distributor.
NOTE: Your stove may not be put into use until the installation has been
approved by the local chimney sweep.

Distance to Combustible Material
For combustible material, such as combustible walls, furniture, etc., for reasons
of safety a number of minimum distances apply. The following minimum
distances apply:
Distance to non-combustible material
To non-combustible material, there should be a distance of 80-100 mm in order
that the stove may release and distribute the heat while you may clean on and
around the stove.
Suspension of PRIO 4
NOTE: PRIO 4 may only be mounted on walls which are not combustible.
PRIO 4 is to be mounted min. 33 cm above floor level if the floor is
combustible.
When it has been decided where and at which height the stove is to be placed,
mark up to the mounting fitting provided. The two top holes are oblong, and
discs are provided on which the hole has been placed a little off centre (see
detail C below). Thus allowing for adjusting the height a little so that the fitting
will be horizontal. After this lock the fitting finally through the two bottom
holes.
150 mm behind
350 mm
To the
side
900 mm
forward

C
C (1 : 2)
Then hook the stove up on the fitting. The stove has two holes fitting the two
top holes of the fitting. Fix the stove on the fitting.
Technical Specifications
Model Height Width Depth Weight
Prio 1 112 cm 55 cm 46 cm 164 kg
Prio 1
w/soapstones
112 cm 55 cm 46 cm 239 kg
Prio 2 112 cm 55 cm 46 cm 164 kg
Prio 2
w/soapstones
112 cm 55 cm 46 cm 226 kg
Prio 3 117 cm 55 cm 46 cm 171 kg
Prio 4 81 cm 55 cm 49 cm 160 kg
Stove hanging in this notch
Mount shadow strip in this hole
before stove is suspended

Mean Values at testing to DS/EN 13240:
Flue Gas Temperature: 293 C
Flue Gas Mass Flow: 5.7 g/s
Rate of Efficiency: 77%
Rated Output: 6.3 Kw
Flue: 12 pa
Chimney
A good draught in your chimney is paramount to how well a stove will burn.
Note that there should be access to cleaning doors.
The effective height of your chimney should typically range between 3.5 and
4.5 metres. Effective height is to be understood as the distance from the stove
top to the top of the chimney. The inside diameter of the chimney should be
min. 150 mm (inside dimension).
All joints and connection points shall, of course, be tight, and the chimney shall
be able to provide a draught of a min.1.2 mm water column (12 Pa), though
preferably a little more.
The wood stove may be connected to chimneys which are also used for other
purposes. To this end, the specific local conditions shall be assessed by a fitter
and/or chimney sweep.
Register
If your chimney has a register, it should have a forced aperture of min. 20 cm2.

Mounting of Smoke Baffle Plates
Below, it has been shown how the smoke baffle plates are to be placed when
viewing a section in the stove from the side.
Each smoke baffle plate is removed separately. Both smoke baffle plates are
removed by lifting up at one side after which they may come clear at the other
side and be taken down into the combustion chamber and out of the door.
Similarly, they are put in place by leading them up slanting-wise up at one side,
and then at the other side, and they are then put into place in the middle.
Combustion Air Supply
It is important for good and clean burning that adequate air be supplied to the
fire. To allow for this, it is, however, a condition that air be supplied to the
room in which the stove has been set up.
Certainly most rooms will have sufficient air, not least if some of the doors
between the rooms of the house are open. In special cases, an air valve may
have to be put in the exterior wall of the room in which the stove has been put
up.
Steel smoke baffle plate
Skamol smoke baffle
plate
Stålrøgvendeplade
Skamolrøgvendeplade

Floor
When placing your new Lotus stove on the floor, it should be put on a non-
combustible plate, for instance of steel or stone material. The plate should be so
large that it will reach a minimum of 30 cm in front of the stove, and 15 cm at
each side of the fireplace opening.
It shall, of course, be ensured that the floor has the carrying capacity required.
Alternatively, appropriate steps will have to be taken to that end.
Chimney Sweep
When your new stove has been mounted, do remember to report the installation
to the chimney sweep. For one thing, the installation will have to be inspected,
and the chimney should also be cleaned by the chimney sweep in the time
ahead.
Use of Stove
Below, the procedure applied at the stove testing by Teknologisk Institut – The
Technological Institute – has been reviewed. This is the procedure generating
optimal combustion on the particular chimney.
Wood quantity and register setting may be varied as individually required for
heating and the draught of the particular chimney. The stove has been tested
with birch wood of a humidity of appr. 18%.
Kindling and Current Stoking at EN testing
1. The ash pan as well as the grate should always be closed completely, also
when kindling.
2. Put about 2 kig kindling wood into the bottom of the stove, stacked crisscross
like a log house. Put 2 firelighters in the middle, and ignite them..
3. Close the door ajar, leaving an aperture of appr. 3 cm. Open the register to
the left under the door completely (pulling it out completely). Leave the stove
like for this for about 8-10 minutes before closing the door completely and
turning the handle into locked position. (Primary air may be added by pulling
out completely the register to the right under the door - thereby opening the
grate and allowing a small volume of air to draw up through the grate . This
may be used as required for kindling as well as for any subsequent stoking.

May only be used for kindling as well as stoking and may not be left open
during the ordinary combustion).
4. The register is damped as required during the kindling.
5. When the fire has burned down to embers (no more flames), open the door
gently so as not to whirl out the embers. Spread out the embers cautiously
using a poker so as to leave them in an even layer.
6. Put three pieces of wood into the stove, totally about 1.8 kg. Two of the
pieces are put at the bottom of the stove parallel with the stove front, at equal
distance to the stove sides and at a reciprocal distance of appr. 1 cm, the third
piece is put on top. The foremost piece will ignite best if it has one split side
facing the door, and one down in the embers. Close the door immediately and
completely.
7. Open the register completely, and after about two minutes set the register so
as to be about one third open. Just how open the register should be may vary
with the draught of the particular chimney but the flames should now
stabilize into a ”calmly burning fire”.
8. When the wood has burned down to embers (after about one hour), start all
over from item 5.
Slow Combustion
On a proper layer of embers feed a fair quantity of wood (3.0 – 3.5 kg
distributed on 3-5 pieces of wood – not one or two big logs). When the fire has
caught on well, adjust the air down. Never adjust down more than still leaving
clear, lasting flames. When this fire has burned down, the period up to the next
stoking may be stretched further by closing the register entirely so that cold air
will not be pulled through the stove.
Adjusting the air supply down too early, or if it is generally too small, will
cause a poor rate of efficiency and a too high emission level to the detriment of
the environment.
Ashes
Ashes may be discarded in the waste bin for refuse collection. The ashes should
always have cooled for 24 to 48 hours before being thrown into the waste bin as
there may otherwise still be embers that may ignite waste or the waste bag.

Sound Advice
Kindling after a protracted interval
If your stove has not been used for some considerable time, the chimney should
be inspected for blocking prior to rekindling.
Cleaning of Stove
All Lotus stoves have been factory treated with original Senotherm lacquer in
”coke” or ”grey” colour. Due to this treatment, the stove will, during the first
kindlings, exude a special odour but that will vanish after a few times. Good
airing to be provided. The surface is maintained by brushing it using a soft,
long-haired auto brush or by using the vacuum cleaner with a brush.
Chimney Fire
In case of a chimney fire, doors and register should be shut so as to cut off the
oxygen supply. Relevant authorities etc. may be called if necessary.
Stove Maintenance – use original spare parts only
Packings may seem to look nice; they will, however, collapse in the heat,
thereby losing their ability to keep your stove tight. Packings should be
replaced as required as it is essential to good combustion and to a clean pane
that your stove is tight.
The shaker grate may in extremely rare cases become worn or crack after use
and may also be easily replaced. Lift the grate and the frame a couple of cm,
release from draw bar, and replace by a new one. The actual frame holding the
shaker grate may also be easily replaced as it lies loose in the Skamol.
The combustion chamber covering may break or become worn. The panels
are made of vermiculite, an insulation material. When worn, the material is to
be replaced not later than when the panels have a thickness of appr. 1.5-2.0 cm.
The material is slightly porous. To prevent breaking of the panels it should be
ensured that the wood is not thrown but laid in the middle of the combustion
chamber. If you happen to break a Skamol panel, this will not have any impact
on the insulating effect of the panel.
Painting of your stove using Senotherm spray may cover stains or small
scratches from kettles or other. Heavy damage to be ground with fine steel
wool, vacuum cleaned, and then sprayed. Shake the spray can very heavily, and
spray on at a distance of 15-20 cm. It is most important that your stove will be