lovelec Polaris User manual

POLARIS
display and control panel①
rechargeable battery②
battery charging connector③
battery switch④
controller⑤
electric motor⑥
motor connector⑦
PAS sensor⑧
CARRIER RECHARGEABLE BATTERY
There is a red rocker switch on the right side of the bottom of the battery (0 – OFF,
– ON). Turn on the battery (position ) before riding. Store the battery turned off (position
0).
The battery is secured by a key lock. The lock is on the left side. When turning the key
by 180° to the left you will open the lock, when turning the key by 180° to the right you
will secure the lock (see the illustration on the lock).
Keep your battery locked, unlock it only when there is a need to remove it. We recommend
checking the battery is locked before riding and when parking in order to avoid any
damage or theft.
f you want to remove the battery, first you need to unlock its lock (see above). You will
unplug the battery by pressing the carrier with your thumb while positioning the index,
middle and ring finger on the battery groove on the bottom part of the battery and pulling
the battery backwards. You will plug in the battery by inserting it to the dock station. Please
remember to secure the battery in the dock station by the lock (see above). Make sure the
battery is inserted to the stop, otherwise you will be unable to lock it. nsert and remove the
battery from/into the dock in a horizontal position tightly in line with the battery dock.
There is a LED charge indicator on the upper part of the battery. Push the button
for an indication. 4 diodes = the battery is charged > 80 %, 1 red diode = the battery
is charged < 20 %. Charge the battery as soon as possible if it indicates just one red diode.
The LED charge indicator operates only when the battery is on (position ). The charge
status can also be found on the display (see below).
There is a charging connector on the left side of the battery with a rubber plug. You can
keep the battery in the carrier while charging or remove the battery from the dock.
There is a button on the upper side of the battery for turning on/turning off the rear
light, which is integrated into the battery and is powered by the battery.

DISPLAY BIGSTONE C300S
You can switch on the power supply of the e-bike
motor by briefly pressing the M button
( left, middle ).
You can switch off the power supply of the e-bike
motor by pressing the M button ( left, middle )
for a few seconds.
The motor assistance level Assist (0–5) is displayed in the lower left corner (5 = highest,
1 = lowest, 0 = without any assistance). You will increase the motor assistance level
by briefly pressing the + button ( left, top ). You will decrease the motor assistance level by
briefly pressing the – button ( left, down ).
The charge indicator (battery symbol in the upper left corner of the display) shows
the charge level: 6 bars = the battery is charged > 80 %, 1 bar = the battery is charged
< 20 %. Charge the battery as soon as possible if it indicates just one bar.
The charge status can also be found on the battery (see above).
Current speed is displayed in the upper right corner ( KM/H ).
The parameters mentioned below are stated in the lower right corner of the display:
– TR P = trip mileage; – T ME = duration of the ride; – ODO = total mileage;
– MAX = maximum speed; – parameters stated above are displayed in a loop.
You can switch between individual parameters by briefly pressing the M button
( left, middle ).
Please contact your dealer in case of an error message ( ).
RESETT NG: TR P, T ME and MAX parameters can be reset all at once. Press the „+“ and the „–” button
at the same time, until there is „1“ displayed in the lower left corner. Reset the parameters by briefly
pressing the „–“ button. You will return to the default data display by briefly pressing both of the buttons
„+“ and „–“.
The display back-light can be turned on/turned off by pressing the + button ( left, top )
for a few seconds.
By pressing the – button ( left, down ) you will activate the walk assistance and the e-bike
will move at the speed of 4–6 km/h (displayed as Assist 6 AUTO in the lower left corner
of the display). By releasing the – button you will deactivate the assistance. The walk
assistance facilitates control of the e-bike (for example when pushing the e-bike uphill).
This function is to be used only for the e-bike control (pushing), not when setting off
or riding!
The display will be deactivated after approximately 5 minutes of inactivity.
The display cover is made from ABS plastic, which ensures durability for common use.
Do not expose the display to temperatures below –20 °C and above 60 °C.