Lovencare VULU BOOSTER User manual

Read all instructions BEFORE assembly and USE of
product. KEEP INSTRUCTIONS FOR FUTURE USE.
www.lovencare.com.au
VULUBOOST
VULUBOOST

Congratulations
Congratulations on purchasing your
new Vulu Booster seat.
In just a few steps you should be able to
assemble this unique product and have it
ready to meet your beautiful child :)

WARNINGS
TO PREVENT SERIOUS INJURY OR DEATH FROM SLIDING OUT, FALLS, OR TIPPING OVER:
• Never leave the child unattended.
• Always use the restraint system and ensure it is correctly fitted.
• Always check the security and the stability of the chair mounted seat on the adult chair
before use.
• Do not use this chair mounted seat on stools or benches.
• Always use the chair attachment system and ensure it is correctly fitted before use.
• Prevent serious injury or death. Do not use in a motor vehicle.
• This product is intended for children able to sit up unaided and up to 3 years or a maximum
weight of 15 kg (33lbs).
• Position the adult chair with the chair mounted seat placed in a position where the child is
not able to use its feet to push against the table or any other structure as this can cause the
adult chair supporting the chair mounted seat to tip over.
• Do not use the chair mounted seat if any part is broken, torn or missing.
• Do not use any replacement parts or accessories other than those approved by or supplied
by Love N Care/Vulu.
• Do not use in water or as a bath seat.
• Always use with the feet provided.
• Always secure child in the restraint.
• The child should be secured in the booster seat at all times by the restraining system.
The tray is not designed to hold the child in the chair.
• Never allow a child to push away from table.
• This product is suitable for the minimum dimension of the adult’s chair which the width of 453mm,
the depth of 453mm.
• This product is suitable for the minimum height of 365mm of the adults chair backrest.
WARNING:
Care & Maintenance!
• Sponge clean only.
• Change or repair parts if required. Only use spare parts recommended by Love N Care.
• Clean the booster regularly.
• Excessive exposure to the sun or heat may cause fading of colours or warping of parts.
• When not in use, make sure booster seat is dry and leave in a dry area.
• To wash fabric seat, with cold water and mild soap. Air dry.
• No bleach. Drip dry. Do not put in dryer. Do not iron or dry clean.
• Metal and plastic parts can be wiped clean with a soft damp cloth and dried with a soft cloth.
Do not use abrasive cleaners or solvents
• Check the product for loosen screws,worn parts,torn material regularly and replace or repair
parts them.

Warranty against defects
All love n care products are guaranteed for twelve months from the date of purchase. Our goods come
with guarantees that cannot be excluded under the Australian consumer law.
You are entitled to a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced
If the goods fail to be of acceptable quality and the failure does not amount to a major failure. This
covers against faults which develop through faulty materials and workmanship. Misuse, accidental
damages, normal wear and tear or neglect are not covered.
If a fault becomes apparent, please return the item to the store of purchase with your receipt. You must
inform the store what the defect is. We will then arrange for its repair or it will be assessed for replacement
as expediently as possible. The benefits of this warranty are in addition to other rights and remedies under
the law in relation to the goods and services to which this warranty relates.
If you are unable to return the item to the store of purchase, you can contact love n care on freecall
1300732599. We will then organise for either somebody to inspect the item or arrange for a courier to pick
it up and return it back to you.
For more information please contact:
Love N Care Pty Ltd
Email: [e-mail]
Web: www.lovencare.com.au
Phone: [phone]
Fax: [phone]

Parts
What should be included in the box.
A
B
Seat Cushion Snack Tray

Assembly
1
2
3
press
to remove
Attaching and removing the tray
OK
Place the tray into the centre position as shown at point 1. The seat should click into
place.
To remove the tray press the buttons located on the centre crotch position located
on the tray and lift out as shown at point 3.
CLICK

Assembly
CLICK
Back Strap Assembly.
1. Wrap the straps around the desired seat,
until the buckles meet and click into place.
2. Pull on the straps to tighten so that the seat
is nice and firm.
3. Place the straps into the clips on the straps
to ensure the straps are not a hazard.
Back Strap
Bottom Strap
Bottom Strap Assembly.
1. Wrap the straps around the bottom of the seat,
until the buckles meet and click into place.
2. Pull on the straps to tighten so that the seat
is nice and firm. Place the straps into the clips on
the straps to ensure the straps are not a hazard.
CLICK

Assembly
Before assembling onto a seat the minimum size of the seat is as below.
453mm
453mm
365mm
OK OK

Assembly
1
press
2
press
rotate 90 degrees rotate 90 degrees
Seat rotation
To rotate the seat press the button located on the front of the seat and turn to
the desired direction.

Assembly
Harness Assembly
Place the child in the seat and place the left
and right side strap buckles into the crotch
strap holders. Adjust the sliders on the straps to
the required size by pushing
USE THIS HARNESS AT ALL TIMES
WARNING

6 months - 12 months
Recommended Usage - stages
6 months - 18 months
12 months - 36 months
Fully Assembled
Remove front Tray
Remove cushion and Tray
Stage 1
Stage 2
Stage 3
6
R
1
R

Head Office:
Love N Care Australia Pty Ltd.
297-299 Canterbury Rd, Revesby
NSW 2212 Australia
Contact No: 02 9774 4655
Fax: [phone]
Email: [email protected]
www.lovencare.com.au
Contact Us