Lovencare SLEIGH HK25 User manual

SLEIGH COT
HK25
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

A
B
C
D
F
G
G
H
I
J
K
L
M
Left End
Right End
1pc
1pc
1pc
1pc
1pc
A
B
C
D
E
Fixed Side
Mattress Base
Drop Side
1pc
FFront Top Cap
2pcs
GSupport Rail
Drawer Front 1pc
1pc
1pc
1pc
1pc
H
I
J
K
L
1pc
M
Drawer Side Left
Drawer Side Right
Drawer Back
Drawer Bottom
Drawer Bottom Rail
Parts List

Hardware Kit
step1
step2 (5) M6x50mm x3
step3
Tools x1(13) Allen Key
(14) Screwdriver x1
Sofa x6
Mattress
(6) M6x70mm
(7) Nut
(8) Iron Plate x4
step8
x2(5) M6x50mm
(7) Nut x2
step7 (10) 15x12mm Cam Lock x2
step6 (9) 6x44mm Metal Dowel Screw x2
(1) Knob Bolt
(2)
(3) Nail
(4) M6x25mm x8
x2
x2
x2
(6) M6x70mm x4
step4 x4
x4
step10
x4
x4
x4
(6) M6x70mm
(7) Nut
(8) Iron Plate
(4) M6x25mm
(11) M6x12mm
(12) M6 x4
x4
x4
x2(5) M6x50mm
(7) Nut x2
(11) M6x12mm
(1) Knob Bolt x2

G
4
13
2
1
AB
F
D
Step 1 Setting up the ends
Step 2 Assembling the dropside
5
13
fig 1.
fig 2. fig 3.
fig 4.
1. Attach the dropside catch (2) and insert bolt (1) into cot ends A and B as
shown in Fig 1. Please make sure the dropside catch is attached correctly.
Tighten with screwdriver (14).
2. Attach the nail with washer (3) as shown in fig 2. Tighten with screwdriver.
3. Attach the 2 support rails (G) to the Left End (A) and Right End (B) using
8pcs bolts (4) with Allen key (13) as shown in fig 3.
Attach the front top Cap (F) to
dropside (D) using 3pcs bolts (5)
with allen key (13) See fig 4.

Step 3 Attaching the fixed side
Step 4 Attaching the base
A
C
13
fig 5.
fig 6.
fig 7.
To Attach the ends (A & B) to the fixedside (C) use 4pc bolts (6) and tighten
with allen key (13). See Fig 5.
Attach the mattress base (E) to the Left End (A) and
Right End (B), using 4pc iron plates (8) and 4pcs bolts (6)
insert nut (7) into the base and tighten with allen key (13). See Fig 6 & 7

Step 5 Attaching the dropside
Step 6 Assembling the drawer
H
K
9
14
To attach the dropside (D) the assembled dropside catch on the end should be
fed through the bottom of the top rail (shown in fig 8) and the bottom screws from
the sides should feed into the bottom rail (shown in fig 9).
fig 8.
fig 9.
fig 10.
Attach 2pcs metal dowel screw (9) to drawer front (H) and drawer back (K) by
screwdriver (14). See Fig 10.

H
K
M
H
K
M
J
Step 7 Attaching side on the drawer
Step 8 Attaching ends on the drawer
10
7
fig 11.
fig 12.
Attach the drawer bottom rail (M) to drawer front (H) and drawer back (K) with
2pcs cam locks (10) and tighten with screwdriver (14) See fig 11.
Attach the drawer side Right (J) using 2pcs (5) bolt with the 2pcs nuts inserted
into the Sides (H) and (K). Then tighten with Allen key (13) See Fig 12.

Step 9 Inserting the drawer base
Step 10 Attaching the ends to the drawer base
H
L
K
M
J
J
H
I
K
5
13
fig 13.
Insert the drawer bottom (L) to drawer front (H) and drawer back (K) along
the inner rails.
Attach the drawer side left (I) to drawer front (H) and drawer back (K)
using 2 bolts (5) and nuts (7) and tighten with allen key (13) see fig 13.

Step 11 Inserting the drawer to the cot
Attach the drawer on the runners located under the base.

Using the dropside

How to adjust the Mattress level
fig 14.
fig 15.
fig 16.
fig 17.
Before raising the mattress base to the highest position, take out
the bolts (11 and 12) that are inside the holes as shown in fig 14.
Attach 4pc bolts (6) to the left and right sides to fix the mattress
base to the cot and align with (7) nut. (see fig 16.) Tighten with
allen key (13) (fig 15) Attach 4 pcs bolts and cap(4 & 12) and iron
plates (8) to fill out the holes. (Fig 17)
Warning: Please ensure the unused mattress base mounting holes
on the end panels are blanked off with the supplied blanking
screws and tightened to prevent finger entrapment and swallowing
hazards.

Convert cot to sofa
2
1
3
fig 18.
fig 19.
fig 20.
fig 21.
1. Loosen the bolts on the left and right sides. Remove the dropside.
Tighten the bolts.
2. Remove the Bolts (1,2 and 3) then insert bolts (1 and 11) as shown in
Fig 18-21.

fig 22.
Convert Sofa to junior bed.
1. Remove the fixed side.
2. Attach the (11) bolts to fill in the holes and tighten with allen key (13)