Lpower Avenger RX User manual

Avenger RX All-in-1 (ver1.0)
User Manual
Welcome to Lumapower
Please take a moment to register your product on our Web site at
http://www.Lumapower.com. It enables us to keep you posted on our latest advancements,
and helps us to better understand our customers and build products that meet their needs
and Expectations.
This product has been designed and manufactured to the highest quality standards. However,
if something does go wrong with this product, Lumapower and its national distributors
warrant free of charge labour and replacement parts in any country served by an official
distributor.
Unpacking: Check the product carefully. If it has been damaged in transit, report the
damage immediately by calling your dealer and/or the shipping company that delivered it.
Read Instructions. All the safety and operating instructions should be read before the
product is operated.
Follow Instructions. All operating and use instructions should be followed.
Replacement Parts. When replacement parts are required, be sure the replacement parts
have the same characteristics as the original part. Unauthorized substitutions may cause
damage to the unit.
Introduction
Lumapower ARX supports input voltage from 0.9V to 4.2V. It is powered by 1 x AAA battery
(Alkaline, NiMH, Li-ion) or 2 x AAA battery (Alkaline, NiMH). ARX fitted with pure white LED
module driven by current regulation circuitry to achieve a consistent level of light output for
the useable life of the batteries. (Never use 2x10440 !!!)

ARX features both clicky and twisty switch and multi-level digital output control circuit.
Half-press the tail switch to power on ARX momentary, and full press to lock it for constant
on.
Digital output control (Smart UI)
Half press to cycle the output from Low, Medium, Normal and High.
At each output level, with a full press to lock it.
You can change the output by power off and on (within 1 second). As the powered on over 1
second will remains the same output with your next start.
Tactical Lock – Select the desired level and remains the power on for 1 second, then 4
half-press within another 1 second to lock the selected level. Further power on will always
remains the same output until Unlock.
Unlock – 4 half-press within 1 second
Battery Installation
Unscrew the Head housing and insert new battery with positive ends towards LED assembly.
Replace bezel and hand tighten. Depress tailcap pushbutton switch to test.
Note: It would not light if battery is inserted in wrong direction.
Mechanical polarity protection will protect the circuit from wrong battery insertion.
CAUTION: ARX flashlights are high-output lighting devices. Due to possible eye
injury, DO NOT look directly into the reflector when the light is switched on. Safety is
your responsibility, too.
External surface temperature will rise during prolonged operation; this is a normal operating
phenomenon.
Battery Replacement
If there is significant decrease in brightness of light output you should replace the battery.
Unscrew the Head housing and remove the old battery. Insert a new battery as mentioned in
Battery Installation Guide
WARNING: Lithium batteries can explode or cause burns if disassembled, shorted,
recharged, exposed to water, fire, or high temperatures. Do not place loose batteries in a
pocket, purse or other container containing metal objects or store with hazardous or
combustible materials. Store in cool, dry, ventilated area. Follow applicable laws and
regulations for disposal.
Maintenance
Clean and lubricate threads with a clean cloth and apply thin coat of silicon-based lubricant to
rubber O-rings. Note: Do not use petroleum-based lubrication on O-rings. After prolonged
exposure to moisture, the bezel and batteries should be removed, inspected, and dried if
necessary.
WARNING: Lumapower reflector is made with high precision process. Do not touch
or clean the reflecting surface using any cloth which may cause damage to the surface
material affecting the illuminating performance.
Non-use Periods.
If ARX is left unused for long period, the installed battery should be removed from the unit.
Output & Runtime
Accurately specifying light output (lumens) and runtime is complicated for LED flashlights.
Installed batteries and operating temperature are the main factors affecting the light output
and runtime. Lumapower doesn’t guarantee its products can reach the specification under the
using condition of users.
Specification (version 1.0)
LED : Cree XP-E2 R3 CW（Optional Neutral White, Warm White）
Please note that Neutral White and Warm White with lower lumens.
All lumens output on this manual refers to Cool White.
For details, please visit www.cree.com
Reflector : SMO type, Aluminum
Max. OTF Lumens : 3, 11, 32, 78 (NiMH/Alkaline); 3.5, 20, 78, 215 (4.2V
Li-ion 10440)
Runtime A (minutes) : 80 (Ultra), 135(High), 360 (Medium), 1000 (Low) :
800mAh NiMH
Runtime B (minutes) : 200 (Ultra), 350(High), 850 (Medium), 2500 (Low) :
2 x 800mAh NiMH
Batteries 1xAAA : 1.2V NiMH AAA, 1.5V AAA, rechargeable Li-ion (10440)
Batteries 2xAAA : 1.2V NiMH AAA, 1.5V AAA (never use 2x10440 !!!)
Length standard : 71mm (Twisty style) 87mm (Clicky style)
Length pen style : 131.5mm
Bezel/Tail Diameter : 14mm
Weight standard : 11.5g (Twisty style) 15g (Clicky style)
Weight pen style : 24.3g (without battery installed)
Material : T6061 aircraft aluminum
Body coating : Type III HA Black
Accessories : spare o-rings, pocket clip, lanyard, diffuser tip.
Battery is not included.
Specifications: All product specifications/features are subject to change without notification.
Reflecting surface