LRS RX-CS6 User manual

Guest Pager
Guest Pager Pro
Guest Pager Note
GUEST PAGING RECEIVER
MODELS: RX-CS6, RX-CS7, & RX-AT9
Long Range Systems, LLC.
LRSUS.COM | 800.437.4996 | 214.553.5308
USER MANUAL

USER MANUAL | RX-CS6, RX-CS7, & RX-AT9 LRSUS.COM | 2
TABLE OF CONTENTS
General Information 3
Setup and Use 3
Charger Installation 3
Operation 3
Product Specifications 4
Cleaning 4
Troubleshooting 5
Service Questions and Answers 6
What To Do If The System Malfunctions 6
System Repair After The Warranty Expires 6
Ordering Additional Pagers 6
Loss Deterrent and Recovery 6
Warranty 6
FCC Information 7

USER MANUAL | RX-CS6, RX-CS7, & RX-AT9 LRSUS.COM | 3
GENERAL INFORMATION
The Guest Pagers are used in conjunction with the LRS transmitters. The guest pagers are
used as an on-premise paging system to increase eciency by alerting customers who
are waiting, usually for services or goods.
SETUP AND USE
The low profile devices are rechargeable, water resistant, and can flash, and vibrate when
called by an LRS transmitter. To begin using your pagers, locate the charging base plate
near a power outlet and charge them for 16 hours.
Charger Installation
1. Install the charger base plate per the directions received with the charger kits.
2. Charge pagers for 16 hours prior to first use.
Note: Keep rechargeable pagers on charge even during extremely long periods of
inactivity.
WARNING:
Do not stack more than 15 guest pagers on a single charger base plate. Do not connect
more than 2 charger base plates to a single power supply. Only use the power supply that
came with your charger. Damage caused from improper electrical connection including
but not limited to the incorrect power supply is not covered under the standard warran-
ty. If you’re uncertain about which power supply to use, contact our customer support
department at 800.437.4996
Operation
1. When a guest arrives, remove a pager from the charging stack. Pagers will light up
and vibrate (if enabled) for 2 seconds.
2. Record the pager number and hand to your guest.
3. Page the pager by entering the number into the transmitter.
4. LRS Guest Pagers will flash or vibrate (if enabled) depending on the page mode sent
by the transmitter. Note: Beep is no longer supported. Beep modes will still flash
and vibrate (if enabled) with no audible beep.
5. Transmitters can also send predefined time limits for each of the pager alert modes.
See transmitter manual for details.

USER MANUAL | RX-CS6, RX-CS7, & RX-AT9 LRSUS.COM | 4
PRODUCT SPECIFICATIONS
Required Voltage: 110-120V outlet for pager chargers, LRS issued 10VAC, 4.0-4.2A pow-
er supply included in kit
Battery Type: Nickel Metal Hydride (NiMH). Rechargeable.
Battery Life: Approximately 3-5 years
Battery Charge Life: Approximately 24 hours (depends on how often they are paged).
Recharge time: 16 hours minimum from completely discharged.
Operating Range: Up to 1/4 mile
Dimensions: 4.25” x 4.25” x .75”
CLEANING
LRS pagers are made from industrial-strength, polycarbonate material. However, this ma-
terial is susceptible to hairline cracking if non-approved cleaners are used. When clean-
ing LRS pagers, you should only use ETHYL ALCOHOL (ethanol) or ISOPROPYL ALCO-
HOL-BASED CLEANERS. We have done extensive testing with available cleaning materials
and have not found any issues with either ethyl alcohol (ethanol) or isopropyl alcohol
(IPA). ALL other cleaners are not recommended for use on any of our pagers.
To clean the equipment:
1. Take a clean cloth and an isopropyl-alcohol based cleaner
2. Wet the clean cloth with the isopropyl alcohol cleaner
3. Wipe down the pagers or equipment
4. When dry, place rechargeable pagers back on charge
WARNING:
Cleaning your equipment with any other non-approved cleaners can weaken plastic and
cause hairline cracks. Pagers and equipment that are cleaned with unapproved cleaners
and suer cracking will not be covered under warranty. Do not submerge any LRS paging
equipment in any type of liquid as this will also damage the equipment and is not covered
under the standard warranty.
Many alcohol-based sanitizers add quaternary ammonium (aka “quat”) to the mix. Long-
term exposure to quats will damage polycarbonate. A commonly used quat is benzalkoni-
um chloride.

USER MANUAL | RX-CS6, RX-CS7, & RX-AT9 LRSUS.COM | 5
TROUBLESHOOTING
Pager Shows an Error Code (CS7 and AT9 Only)
1. If code is E007, E008, or E009 try over-the-air (OTA) programming. See transmitter
manual for specific instructions on OTA programming a pager.
2. For all other codes, contact LRS for service.
Pager Does Not Receive Pages
1. Be sure that the pagers are charged.
2. Be sure transmitter power is plugged in and display is lit.
• If display is blank, check power supply as described below.
• If display is lit, check transmitter functions described in transmitter’s users manual.
3. Pagers will flash and may or may not vibrate depending on a preprogrammed
configuration when removed from the charger base plate.
Check The Power Supply
1. Be sure the wall outlet that the power supply is plugged into is working (plug anoth-
er device into it and see that it works properly).
2. Be sure the wire that plugs into the side of the transmitter is plugged in securely.
Charging Check
Please take note of the following charging requirements and functions.
1. A maximum of 15 pagers may be stacked on one charging base plate at a time.
2. If your system has more than 15 pagers and you only have one charging base plate,
call Long Range Systems to purchase additional.
3. If your system has 2 or more charging base plates, check that the jumper wires
between the base plates are connected securely.
4. Pagers on charge will flash a red LED light every 5 seconds, forming an upward mov-
ing red light on the pager stack.
5. A maximum of 2 charging base plates per power supply are allowed.
6. Check for dirty charging pins on your guest pagers. To clean, use a damp rag, and
wipe the 4 metal contacts on the front and back of each pager.
7. Be sure that all pagers are plugged in and charging when not in use. Even for long
periods of inactivity.

USER MANUAL | RX-CS6, RX-CS7, & RX-AT9 LRSUS.COM | 6
SERVICE QUESTIONS AND ANSWERS
What to do if the system malfunctions
Should your paging system ever fail to function properly, refer to the previous trouble-
shooting section. If you’ve followed all the steps and requirements and your system is still
inoperable, you may submit a support request at support.LRSUS.com or call Long Range
Systems at [phone] Monday through Friday 8:30 am to 5:00 pm Central Time.
For after hours inquiries, please follow the instructions on the support line. LRS
Customer Support will return the call as soon as possible. Please keep in mind that options
are limited over the weekend.
System Repair After Warranty Expiration
Call Long Range Systems before sending a non-warranty item in for repair.
Ordering Additional Pagers
Call Long Range Systems at 800.437.4996 or 214.553.5308 to place your order.
Loss Deterrent and Recovery
Return address labels on the back of all of your equipment are highly recommended.
Should any of your pagers be taken o premise, this will help them find their way back to
you. You may order return address labels from LRS or print them yourself.
WARRANTY
Long Range Systems, LLC. warrants this product against any defects that are due to
faulty material or workmanship for a one-year period after the original date of consumer
purchase of the complete paging system (transmitter, pagers, and charger). This warranty
does not include damage to the product resulting from accident, misuse or improper elec-
trical connection. If this product should become defective within the warranty period, we
will repair or replace with equivalent product, free of charge. We will return your product,
transportation charges prepaid standard FedEx Ground shipping, provided the product is
shipped prepaid to:
Long Range Systems, LLC.
4550 Excel Pkwy., Suite 200
Addison, TX 75001
No return or replacement can be received without prior authorization and the proper
RMA# posted to the outside of the shipping container.
This warranty gives you specific legal rights and you may also have rights that vary from
state to state.

USER MANUAL | RX-CS6, RX-CS7, & RX-AT9 LRSUS.COM | 7
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a particular instal-
lation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment o and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
Consult the dealer or an experienced radio/ TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could
void the user’s authority to operate the equipment.
050515