LTL Home Products Reflections Spirite User manual

Installation Instructions
REFLECTIONS
DESIGNER LED MIRRORS
by LTL
ELECTRICAL SAFETY INSTRUCTIONS
All connections must be installed by a licensed
electrician, in accordance with current building codes.
Consult a qualified electrician.
IMPORTANT
Always switch off the electrical supply at the main
during installation and maintenance. It is
recommended that the circuit breaker is switched off
for the necessary circuit before installation
commences.
Fitting in Bathrooms is subject to the appropriate
building code Regulations. This product is NOT
suitable for outside zones. It is also Not suitable for
installation in saunas, steam rooms or shower
cubicles. This product is only suitable for permanent
installation. DO NOT connect to a trailing plug
and socket outlet. This product is only suitable for
indoor use. Do not attach the product to surfaces that
are damp or otherwise electrically conductive.
INSTALLATION CARE & SAFETY
Wear suitable eye protection when drilling. Take care
when using power tools. Beware of hidden cables or
pipes. Take care if drilling on tiled surfaces in case the
drill slips. A piece of masking tape applied to the wall
before marking out the fixing holes will stop the drill
from wandering.
CLEANING
It is recommended that the unit is cleaned with a soft, dry, non
abrasive cloth when turned off. Never use cleaning agents or
abrasive materials on any type of surface finish. Do not allow
moisture to come into contact with the electrical components.
125 Rt. 61 Schuylkill Haven, PA 17972
1-800-360-1585 • fax [phone] • [email protected]
www.ltlhomeproducts.com
LED ILLUMINATED MIRROR
Spirite
IMPORTANT
DO NOT strike glass components with hard or
pointed items. DO NOT place very hot or very
cold items against or in close proximity to glass
surfaces unless an adequately thick insulation
materal is used to prevent such items coming in
contact with the glass. The nominal thickness of the
mirror glass used in this product is 1/4” and is flm
backed for safety. If the glass becomes chipped or
broken replace immediately.

Installation Instructions
1. Remove the packaging taking special care with the
doors and separate shelves. Open the cabinet doors
and remove the screws on the doors. Take care not to
lose the screws.
2. Using a level,
mark off a horizontal line, and ensure
that the ends of the brackets are spaced to the width
between the inner edges of the vertical aluminium
extrusions (see illustration 1). Mark off the holes using a pencil.
3. Note: Screws supplied are only suitable for stud
walls. For drywall walls use special wall fasteners,
available from DIY or hardware stores. Seek advice from
a specialist about the suitability of screws to be used.
Drill the required holes and insert wall screws.
4. Screw the
bracket to
the wall using the
screws provided.
Please ensure the
screws are fully tight
but take care not to
overtighten.
5. Before making
any electrical con-
nections it is necessary to turn off the main electricity sup-
ply. This unit is provided with a supply cable already fit-
ted. This cable should be fitted to the household lighting
circuit or to a fused 3 AMP supply. Connections should
be made in accordance with the latest regulations. This
cabinet is manufactured to CLASS 1 and requires an
earth connection.
Example 2
Illustration 1
Example 2
C
D
E
Release Leve
Magnet
Storage
Bar
E
E
F
G
Release Lever
Magnet
Storage
Bar
Example
Spirite
LED ILLUMINATED MIRROR
125 Rt. 61 Schuylkill Haven, PA 17972
1-800-360-1585 • fax [phone] • [email protected]
www.ltlhomeproducts.com
IR Sensor
OPERATING INSTRUCTIONS
•To turn ON or OFF the LEDs, wave the hand across the IR sensor
CHANGE LIGHT INTENSITY
• Hold the hand in front of the IR sensor, while the mirror lights are ON, until
desired brightness is achieved.
• Restart by waving the hand across the sensor at preselected intensity settings.
Portrait or Landscape

The next step is to make the electrical connection from the mirror to the
mains supply. Use the connection wire found at the rear of the mirror to make the
necessary connections. A second person will need to hold the mirror in place whilst
made.
Strip wires to a suitable
length. DO NOT connect
to a plug & socket outlet.
THIS PRODUCT IS MANUFACTUREDTO CLASS I
CATEGORY AND MUST HAVE AN EARTH CONNECTION.
! IF IN DOUBT CONSULTYOUR ELECTRICIAN !
COLOUR CODING:
L - Live = Black
N - Neutral =
- Earth = Green
Installation Instructions:
Mains Supply
-220 240V AC
electrical connections are
White
Installation Instructions
REFLECTIONS
DESIGNER LED MIRRORS
by LTL
LED ILLUMINATED MIRROR
125 Rt. 61 Schuylkill Haven, PA 17972
1-800-360-1585 • fax [phone] • [email protected]
www.ltlhomeproducts.com