Lu ÜNO User manual

ÜNO/DÜO
Installation Instructions
Revision
English
March 2022
V2

TABLE OF CONTENTS
ABOUT THIS GUIDE .............................. 3
IMPORTANT SAFETY INSTRUCTION .... 3
LÜ INSTALLATION
INSTALLERS POLICIES......................... 4
PACKAGE CONTENTS........................... 5
REQUIRED ITEMS FOR THE
INSTALLATION..................................... 6
TECHNICAL SPECIFICATIONS.............. 7
ÜNO conguration.....................................7
Light and sound module ............................8
Heart module ............................................9
INSTALLATION CONFIGURATION....... 10
ÜNO & DÜO..............................................10
GYM CONFIGURATION ....................... 11
ÜNO Installation Conguration ................11
ÜNO wiring diagram.................................12
DÜO wiring diagram.................................13
PALESTRA CONFIGURATION.............. 14
ÜNO installation diagram.........................14
ÜNO wiring diagram.................................15
DÜO wiring diagram.................................16
VOICEMEETER SETTINGS .................. 17
INSTALLATION CONFIGURATION....... 20
GYM (D) ..................................................21
Palestra (D) .............................................22
Camera module (E)..................................23
Projection module (F) ..............................24
Heart Module (G).....................................25
Connection - Cables (H)...........................26
Projector alignment (I).............................27
System Startup (J) ..................................28
CAMERA CALIBRATION...................... 29
LIGHTING AND SOUND....................... 31
ACCEPTATION OF INSTALLATION...... 32
CONTACT INFORMATIONS................. 33

3
ABOUT THIS GUIDE
The Lü interactive system installation manual provides basic product information such as safety and operation.
IMPORTANT : Do not modify this product! Changes or modications not expressly approved by the
manufacturer could void the user’s warranty.
The information and specications contained in this installation manual are subject to change without notice.
Disclaimer
IMPORTANT SAFETY INSTRUCTION
Do not use this system near water.
Clean only with a dry cloth.
Do not block any ventilation openings.
If mounting the product overhead, make sure there is adequate support for the product’s weight and always
secure the product to the structure using a safety cable. Install the product following best practices and in
accordance with local laws and regulations.
Only use accessories specied by the manufacturer.
Only plug this system after installation is completed and proper verication.
Always connect the product to a grounded circuit.
Do not use the Lü system in an environment where temperatures exceed +40 °C (104 °F).
Refer all servicing to qualied service personnel. Servicing is required when the system has been damaged
in any way, such as power-supply cord or plug is damaged, liquid has been spilled, objects have fallen
into the system, the system has been exposed to rain or moisture, does not operate normally, or has been
dropped.
To completely disconnect AC power from the system, shut down the computer properly, the power supply
cord must be unplugged from the ceiling and the circuit breaker on-off position.
Lü loudspeakers are easily capable of generating sound pressure levels sucient to cause permanent
hearing damage to anyone within normal coverage distance. Caution should be taken to avoid prolonged
exposure to sound pressure levels exceeding 90 dB.
01
06
07
11
08
10
09
02
03
05
04

4
LÜ INSTALLATION INSTALLERS POLICIES
Responsibility
Lü Interactive Playground Inc. is committed to provide a product that has been fully tested and was fully functional
at the time it was inspected in its Canadian warehouses.
It is the buyer’s responsibility to validate the condition of the product upon receiving it.
The installer assumes all liability resulting from accidents or damage to the product that occurred during the
installation process. In particular, they will be responsible for the repair and shipping costs for the spare parts.
The methods used, the procedures followed and the safety measures put in place during the installation
engage the responsibility of the installer, and this, for the total lifetime of the product.
For any further questions, information or validations, please contact our facility coordination
team at [email protected].

5
Heart module
Lü management system.
Camera module
3D camera system.
Lü system remote controller
Light & sound module
6 x 200 watts LED spotlights
to manage the ambient
lighting and general colors,
2 motorized LED light xtures
for special light effects and
1 powerful 2400 watts
sound system.
2 X Stabilization cables
system
Remote protection case Headset Microphone Xvive U3
Projection module
5200 lumens WXGA* projector
protected in a custom
enclosure.
*WUXGA in Europe
Projector’s remote controller
PACKAGE CONTENTS
Each ÜNO/DÜO conguration consist of:

6
REQUIRED ITEMS FOR THE INSTALLATION
The following items are not included in the box :
All the material needed for structural hanging on the ceiling depending of construction type (ex. Cantruss,
1/2” [13 mm] threaded rod, bolts and nuts, etc.).
Security steel cables and fasteners to secure components directly to building structure, second safety,
3/16” (5 mm) cable for the main unit and 3/32” (2.5 mm) cable for the projector (length to be determined by
the installer).
Self-drilling #8 2/3” (19 mm) metal screws (3 minimum).
Lift system for persons (ex. scissor lift or scaffolding).
Tools (cable cutter, hex key [5 and 6 mm], wrench [7/16” and 3/4” at minimum], portable band saw and
small angle grinder with metal cutting wheel).
DN 40 (1 1/2”-11.5 NPS) threaded pipe for hooking the projector module (length to be determined by the
height of ceiling; the bottom part of the projector should be at 20’ [6 m] from ground).
DN 40 (1 1/2”-11.5 NPS) threaded pipe for hooking the camera module (length to be determined by the
height of ceiling; the bottom part of camera should be at 18’ [5.5 m] from ground).
2 celling plates (6 x 6” [150 x 150 mm]) or 8 x 8” [200 x 200 mm]) for receiving the projector and camera
threaded pipes.
1 12’ (3 m) RJ45 network cable
Pump to inate balls.
01
06
07
08
09
02
03
05
04
10

7
TECHNICAL SPECIFICATIONS
ÜNO conguration
Camera module Projector module
15’ from the wall / 18’ high
6” x 4” x 5”
1.5” pipe mounting bracket
or screw on the ceiling
3.05 lb (1.38 kg)
120-240V - 36W (0.3A)
Installation position*
Size (L x W x H)
Rigging
Weight
Power consumption
28’ from the wall / 20’ high
22” x 20” x 16”
1.5” pipe mounting bracket
37 lb (16.78 kg)
120-240V - 470W (0.3A)
IMPORTANT : The installation parameters in this guide are optimal recommendations. These may change
or vary depending on the installation context or space. Contact us for more information on the matter.

8
With speaker Without speaker
16’ from the wall / 20’ high
37” x 76” x 15”
4 hanging points
178 lb (80.74 kg)
120-240V - 1106 W (9.2A)
16’ from the wall / 20’ high or less
37’’ x 46” x 15’’
4 hanging points
or screw on the ceiling
99 lb (44.91 kg)
120-240V - 674 W (5.6A)
IMPORTANT : The installation parameters in this guide are optimal recommendations. These may change
or vary depending on the installation context or space. Contact us for more information on the matter.
TECHNICAL SPECIFICATIONS
Light and sound module
Installation position*
Size (L x W x H)
Rigging
Weight
Power consumption

9
Heart module
12” over the projection (centered)
14” x 23” x 5”
Screw on the wall
18 lb (8.16 kg)
120-240V - 216W (1.8A)
TECHNICAL SPECIFICATIONS
Heart module
IMPORTANT : The installation parameters in this guide are optimal recommendations. These may change
or vary depending on the installation context or space. Contact us for more information on the matter.
Installation position*
Size (L x W x H)
Rigging
Weight
Power consumption

10
INSTALLATION CONFIGURATION
ÜNO & DÜO
Lü can be sold in two different congurations. The ÜNO conguration broadcasts on an interactive wall while the
DÜO conguration includes two ÜNO units projecting on two interactive walls face to face or side by side. All it
takes is a few minor tweaks and additional connections to allow for a synchronized experience occupying the
entire gym.
Heart module
Camera module
Light and sound module
Projector module
ÜNO
DUÖ
A
B
D
C
A A
B B
D D
C C
ABD C

11
GYM CONFIGURATION
ÜNO Installation Conguration
Side view
All units must be mounted to the ceiling and aligned according to the projection surface. The diagram below
shows the optimal position. Some exceptions for special environments can be made, within the exibility margins.
Flexibility margin 19’ (5.8 m) wide
10’ 7” (3.3m) high
Max. projection surfaceOptimal position
D: 15’ (4,5 m)
13’ (3,9 m) to 15’ (4,5 m)
D: 16’ (4,9 m)
15’ (4,5 m) to 18’ (5,5 m)
H: 20’ (6 m)
10’ (3 m) to 24’ (7,3 m)
H: 20’ (6 m)
10’ (3 m) to 24’ (7,3 m)
H: 12” (0,3 m)
H: 8” to 16”
(0,2 m to 0,5 m)
H: 18’ (5,5 m)
10’ (3 m) to 18’ (5,5 m)
Be careful not to have any obstacles in the projection.
Projector Lighting
D: 28’ (8,6 m)
28’ (8,5 m) to 40’ (12,2 m)
Heart

12
GYM CONFIGURATION
ÜNO wiring diagram
Top view
Connect modules 1, 2, 3 and 4 using this diagram
120 Volts cable
HDMI cable
XLR Speakers cable
USB Camera cable
DMX Lighting cable
Network cable (not included)
01
02
03
04
05
06
10’ (3 m) et 25’ (4,5 m) IEC
65’ (20 m)
25’ (7,5 m)
50’ (15 m)
30’ (10 m) et 15‘ (4,5 m)
As required
01
01
01
0106
01 04
05
02
LightingProjector Heart
Top view

13
GYM CONFIGURATION
DÜO wiring diagram
Top view
IMPORTANT
Both computers must be connected to the
same network for the DÜO system to work.
There should be only one DÜO system per
network.
Use the ÜNO wiring diagram to connect the projector, light and sound, camera,
and Heart modules.
Interconnect the two light modules following this diagram.
01
02
Male Female
30’ (9,1 m) + 15’ (4,5 m) DMX Secondary unit cable
50’ (15,25 m) XLR Sound cable
25’ (7,62 m) XLR Sound cable
25’ (7,62 m) / 30’ (10 m) / 50’ (15 m) XLR Sound cable
01
02
03
04
Connect a DMX cable of to
Connect the LEFT out (Black connection) from the primary unit’s
Projector to the in of the secondary unit’s main Speaker.
Connect the RIGHT out (Red connection) from the primary unit’s
Projector to the in of the primary unit’s main Speaker.
Connect the RIGHT out (Red connection) from the Projector of the
secondary unit to the in of the secondary unit’s main speaker.
Top view
01
02
04
03
Secondary unitSecondary unitMaster unit Master unit
Lighting Projector Projector Lighting

14
PALESTRA CONFIGURATION
ÜNO installation diagram
Side view
All units must be mounted to the ceiling and aligned with the projection area. The diagram below shows the
optimal position. Some exceptions for special environments can be made, provided they fall within the margins.
Flexibility margin
Optimal position
UNÖ-DUÖ P
D: 16’ (4,9 m)
15’ (4,5 m) to 18’ (5,5 m)
D: 15’ (4,5 m)
13’ (3,9 m) to 15’ (4,5 m)
H: 20’ (6 m)
10’ (3,0 m) to 24’ (7,3 m)
H: 20’ (6 m)
10’ (3,0 m) to 24’ (7,3m)
H: 12” (0,3 m)
H: 8” to 16”
(0,2 m to 0,5 m)
H: 18’ (5,5 m)
10’ (3,0 m) to 18’ (5,5 m)
D: 28’ (8,6 m)
28’ (8,5 m) to 40’ (12,2 m)
Sound
Heart
Be careful not to have any obstacles in the projection.
Projector Lighting Camera
H: zero clearance
19’ (5.8 m) wide
10’ 7” (3.3m) high
Max projection surface

15
PALESTRA CONFIGURATION
ÜNO wiring diagram
Top view
Use this wiring diagram to connect the projector, light and sound, camera, and Heart modules.
120 Volts cable
HDMI cable
XLR Speakers cable
USB Camera cable
DMX Lighting cable
Network cable (not included)
DMX cable
Top view
01
02
03
04
05
06
07
10’ (3 m)
65’ (20 m)
25’ (7,5 m)
50’ (15 m)
30’ (10 m)
As required
15’ (4,5 m)
01
01
01
01
01
06
01 04
05
03
07
02
Sound
Heart
Sound
Lighting Camera
Projector
NOTE : For Palestra installation, open the projector case, unplug all audio cables from the projector’s
“AUDIO OUT” ports, then plug them into the computer’s “AUDIO OUT” ports.

16
PALESTRA CONFIGURATION
DÜO wiring diagram
Top view
Use the ÜNO wiring diagram to connect the projector, light and sound, camera,
and Heart modules.
Interconnect the two light modules following this diagram.
01
02
01
02
03
04
05
04
05
02
03
01
03
01
DMX 15’ (4,5 m) cable
XLR 50' (15,24 m) Sound cable
XLR 25’ (7,62 m) Sound cable
DMX 30’ (9,14 m) cable
DMX 30’ (9,14 m) cable + DMX 15’ (4,57 m) cable
Top view
Connect a 15′ DMX cable from SpeakerA to the adapter in the
audio out of the primary computer (marked with a red sticker).
Repeat on the other side with the secondary unit between
the Computer and SpeakerC.
Connect the 50′ XLR cable from the computer’s black audio OUT
port to the secondary unit’s free audio IN port.
Connect a 25′ XLR cable from SpeakerA’s audio OUT port
to SpeakerB’s audio IN port. Next, connect a 25′ XLR cable from
SpeakerC’s audio OUT port to SpeakerD’s audio IN port.
Connect the first 30′ DMX cable from the OUT port of the primary
unit’s Heart module to the in port of the primary unit’s light module.
Next, plug a 25′ XLR cable into the top OUT port.
Plug the second 30′ DMX cable into the OUT port of the primary
unit’s light module with the remaining 15′ DMX cable.
Once both DMX cables are connected (30′+15′), plug it into the IN
port of the secondary unit’s lighting module.
Secondary unit
Lighting
Secondary unit
Projector
Master unit
Projector
Master unit
Ligting
Secondary unit
Heart
Master unit
Heart
Speaker A
Speaker B Speaker D
Speaker C
IMPORTANT
Both computers must be connected to the same
network for the DÜO system to work. There
should be only one DÜO system per network.
Male Female

17
VOICEMEETER SETTINGS
01. Open the Windows taskbar, then open Voicemeeter Banana and click on “Menu” at the top right.
02. Uncheck “Lock Graphic User Interface.”

18
03. Open the A1 source menu at the top right and select “WDM: Speakers (Realtek [R] Audio).”
04. Click on “Menu” at the top right, then on “Save Settings…”

19
05. After the window opens, select the XML Document le “Lu-Voicemeeter-settings” and click on
“Save” to agree to overwrite the old save.
06. Click on “Menu” at the top right and check “Lock Graphic User Interface.”

20
INSTALLATION CONFIGURATION
Step by step (A to C)
Choose the best projection location on the wall (center and 4 corners)
The recommended width is 19’ (5.8 m) and the recommended height is 10.7’ (3.3 m). For the ideal position,
the lower end of the screen should be placed at 12” (20 cm) from the oor.Minimal height is 8” (20 cm) from
the oor and maximal height is 16” (40 cm) from the oor.
Mark the 4 corners of the surface of your projection screen on the wall and the position of the Heart,
which is to be centered 8 to 12” higher than the projection
Make sure to always to always have a 16:9 ratio for the screen.
Determine the position of the various modules on the ceiling by measuring the distances from
the projection wall and install the structural suspension elements
Ideally, all modules should be centered in front of the projection wall.
Camera module
Install at 18’ (5,5 m) from the oor and at 16’ (4,9 m) from the wall.Flexibility margin
(maximum tolerance): 12’ (3,65 m) to 18’ (5,5 m) from the oor and 15’ (4,6 m) to 16’
(4,9 m) from the wall. Maximum distance between the camera and the farthest corner
of projection should not exceed 23’ (7 m). The module can be offset ±3’ (1 m).
Projection module
Install at 20’ (6 m) from the oor and at 28’ (8,5 m) from the wallFlexibility margin
(maximum tolerance): 28’ (8,5 m) to 40’ (12,2 m) from the wall (if installed at
recommended height). The module can be offset by ±3’ (1 m).
Light & sound module
Install at 20’ (6 m) from the oor and at 16’ (4,9 m) from the wall.Flexibility margin
(maximum tolerance): 12’ (3,65 m) to 26’ (8 m) from the oor and 16’ (4,9 m) to 18’
(5.5 m) from the wall. The module can be offset by ±3’ (1 m).
Heart module
Install between 8” (20 cm) and 12” (30 cm) above the projection surface centered.
A.
B.
C.