Event Lighting PANBEAM4x4x10 User manual

1
PANEL BEAM
Model No. PANBEAM4x4x10 PANBEAM4x1x10
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this
manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any
errors or omissions. Please consult Event Lighting for any clarification or information regarding this item.
www.event-lighting.com.au
V1.1

2
Safety Instructions
WARNING
• Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
• Do not look at the light source when the device is on.
• CAUTION: This unit's housing may be hot during and after operation.
• Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.
• Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
• Use a safety chain when mounting this device overhead.
• Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• ONLY connect this device to a grounded and protected circuit.
• ONLY use the hanging bracket to carry this device.
• In case of a serious operating problem, stop using immediately.
• The maximum ambient temperature is 104°F (40°C). Do not operate this device at higher temperatures.
Power Input & Power Linking
This device has an auto-switching power supply work with input voltage range of 100~240 VAC, 50/60 Hz.
Link up to the maximum 8A. DO NOT exceed this.
Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.
Product Installation
This device can be mounted in many orientations provided each individual device is secured by the use of correct
mounting bracket.
Use a safety chain when mounting this device overhead.

3
PRODUCT APPEARANCE, LUX CHART, DIMENSIONS
123
4
56 7 8
910 11 12
13 14 15 16

4
CONTROL BOARD OPERATION
Press the Menu until one of the following displayed:
Display Function
1.DMX Address To set DMX
address
2.DMX Channel
To set DMX channel modes:
4x4 Model - CH 04, CH 06, CH 09, CH64
4x1 Models - CH 04, CH 06, CH 09, CH16
3.Dimmer Curve To set dimmer speeds: 01, 02, 03, 04
4.Sound Mode To set sound active mode and the sensitivity (Speed 000 ~ Speed 100)
5.Static Color To set static colors: Static Color R, G, B, GB, RG, RB, RGB
6.Manual Color To set user mode intensity of R, G, B separately for color mixing and strobe rate
7.Auto Program To set built-in automatic programs: Pr 01 ~ Pr 10 and speeds 000 ~100
8.Master/Slave To set Master/Slave modes
Use Up and Down button to select your desired operation, then press Enter to confirm.
DMX Addressing:
After select the "DMX Address" and press Enter, then use Up and Down to set the desired DMX address
(001~512), press "Enter" again to confirm.
DMX Modes
After select the "DMX Channel" and press Enter, then use Up and Down to set the desired DMX mode
(4x4 Model - CH 04, CH 06, CH 09, CH64
4x1 Model - CH 04, CH 06, CH 09, CH16
, press "Enter" again to confirm.
Dimmer Speed Setting:
After select the "Dimmer Curve" and press Enter, then use Up and Down to set the desired dimmer speed
(01, 02, 03, 04), press "Enter" again to confirm.
Sound Mode
Entered "Sound mode", use <UP> and <DOWN> to set the sensitivity Sen 000 ~ Sen 100, press Enter to confirm.
User Mode
This mode allows the user set intensity of R, G, B separately to get endless color mixing from the control
board without DMX controller to set the device to run strobe desired.
Entered user mode "Manual color", use <UP> and <DOWN> to select the “R / G / B" for Colors intensity or "S" for strobe.
Use <UP> and <DOWN> to set the colors intensity values " 0 ~ 255" or Strobe speed values "000 ~ 100"
(Freeze, Slow ~ Fast), then press "Enter" to confirm.

5
Setting Static Colors
Entered "Static Color", you can select the desired solid color via the UP or DOW N buttons and confirm by Enter
(see following graphic).
Mode:
RGBW Models
Static Colour
Value: Function:
R Red
G Green
B Blue
W White
GB Green + Blue
RB Red + Blue
RG Red + Green
RGB Red + Green + Blue
RW Red + White
GW Green + White
BW Blue + White
RGW Red + Green + White
RBW Red + Blue + White
GBW Green + Blue + White
RGBW Red + Green +
Blue + White
Automatic Mode
This fixture has a built-in automatic program.
Entered "Auto Program" mode, use <UP> and <DOW N> to select the built-in programs "Pr01 ~ Pr -12"
then press the "Enter" to confirm.
Use <UP> and <DOWN> to select the operating speed of the program(Value:Speed 000 ~ Speed100, Freeze,Slow ~ Fast),
Mode:
Value: Function:
Auto
Program
Auto program Pr 01 R G B W colors switching
Auto program Pr 02 15 colors switching
Auto program Pr 03 Color Macros
Auto program Pr 04 Chase 1
Auto program Pr 05 Chase 2
Auto program Pr 06 Chase 3
Auto program Pr 07 Chase 4
Auto program Pr 08 Chase 5
Auto program Pr 09 Loop above Pro 01~ Pr 08
Master/Slave Operation
This mode allows for multiple units slave fixtures to follow a single master fixture.
1) Set the master fixture to one of the standalone operating modes: automatic, sound, user mode or static color modes
2) For slave units, entered the Master/Slave mode, select "Slave", press Enter.

6
DMX VALUES
4 Channels Mode: ALL Models
CHANNEL VALUE FUNCTION
1 000-255 Red: 0% ~ 100%
2 000-255 Green: 0% ~ 100%
3 000-255 Blue: 0% ~ 100%
4 000-255 White: 0% ~ 100%
6 Channels Mode: ALL Models
CHANNEL VALUE FUNCTION
1 000-255 Red: 0% ~ 100%
2 000-255 Green: 0% ~ 100%
3 000-255 Blue: 0% ~ 100%
4 000-255 White: 0% ~ 100%
5 000-255 Master Dimmer 0% ~ 100%
6 000-009 No function
010-255 Strobe : Slow ~ Fast(1~30Hz)
9 Channels Mode: ALL Models
CHANNEL VALUE FUNCTION
1 000-255 Red 0% ~ 100%
2 000-255 Green 0% ~ 100%
3 000-255 Blue 0% ~ 100%
4 000-255 White 0% ~ 100%
5 000-255 Master Dimmer 0% ~ 100%
6 000-009 No function
010-255 Strobe : Slow ~ Fast(1~30Hz)
7
000-009 No function
010-023 Auto Program PR 01 R G B W colours switching
024-038 Auto Program PR 02 15 colours switching
039-053 Auto Program PR 03 R G B W colours fading
054-068 Auto Program PR 04 15 colours Fading
069-083 Auto Program PR 05 Colours Macros
084-098 Auto Program PR 06 Chase 1
099-113 Auto Program PR 07 Chase 2
114-128 Auto Program PR 08 Chase 3
129-143 Auto Program PR 09 Chase 4
144-158 Auto Program PR 10 Chase 5
159-173 Auto Program PR 11 Chase 6
174-188 Auto Program PR 12 Chase 7
189-203 Auto Program PR 13 Chase 8
204-218 Auto Program PR 14 Chase 9
219-233 Auto Program PR 15 Loop above Pro 01~ Pr 14
234-255 Sound active

7
8 000-255 Speed of Auto Programs (Slow ~
Fast)
9
000-009 Default dimmer speed
010-070 Non-linear dimmer 1
071-132 Non-linear dimmer 2
133-194 Non-linear dimmer 3
195-255 Non-linear dimmer 4
16 Channels Mode: 4x1 Model
CHANNEL VALUE FUNCTION
1,5,9,13 000-255 Red 0% ~ 100%
LED 1 (1-4), LED 2 (5-8), LED 3 (9-12),
LED 4 (13-16)
2,6,10,14 000-255 Green 0% ~ 100%
3,7,11,15 000-255 Blue 0% ~ 100%
4,8,12,16 000-255 White 0% ~ 100%
64 Channels Mode: 4x4 Model
CHANNEL VALUE FUNCTION
1 000-255 Red 0% ~ 100% LED 1 (1-4), LED 2 (5-8), LED 3 (9-12),
LED 4 (13-16), LED 5 (17-20), LED 6
(21-24), LED 7 (25-28), LED 8 (29-32),
LED 9 (33-36), LED 10 (37-40), LED 11
(41-44), LED 12 (45-48), LED 13
(49-52), LED 14 (53-56), LED 15
(57-60), LED 16 (61-64),
2 000-255 Green 0% ~ 100%
3 000-255 Blue 0% ~ 100%
4 000-255 White 0% ~ 100%

8
TECHNICAL SPECIFICATIONS
Model
PANBEAM4X1X10 PANBEAM4X4X10
Dimensions and Weight
LxWxH (mm) 1050 x 80 x 165 425 x 425 x140
Weight (kg) 4 11.3
Power
Power Supply 100~240V AC, 50/60 Hz
Power Consumption (w) 50 200
Fuse T 1 A, 250 V T 2 A, 250 V
LED 4pcs CREE 10W Quad-color RGBW 16pcs CREE 10W Quad-color RGBW
Operation Modes DMX, Auto, Sound Active, Master/Slave, RGBW Manual Control Mode, Static Colour Mode
Beam Angle 9°
Refresh Rate 11700Hz
DMX Channel 4,6,9,16 channels 4,6,9,64 channels
DMX connection 3 - pin XLR 3 pin & 5 pin XLR
Power Input Socket IEC Neutrik Powercon
Power Output Socket IEC Neutrik Powercon
Pixel control for each LED
LCD display with 4 buttons control
Fresnel lens for color beam
Smooth electronic dimming with a 16-bit 4 Dimmer curve
Oxidation surface treated aluminum Housing
Smart Cooling system without fan
Variable Speed Strobe Effect (1 – 30 Hz)
WARRANTY
Please refer to your local dealer or please contact Event Lighting.