Lucci comfort 121245 User manual

Installation Instructions
1 | Page V1.1 Published on 11 2017
REMOTE CONTROL GLOBE LED KIT
SKU# 121245
Remote Rated Voltage: 2 X 1.5VDC
Globe Rated Voltage: 220-240V AC, 50Hz
Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and
follow all instructions carefully before using the product. Please keep instructions for future reference.
Important information before Installation
•This product is covered by a 3 year warranty.
The warranty is from date of purchase, not the date of
installation.
•This globe is not suitable for use with solid-state or phase type
dimmer switches. Warranty will be void if
the fitting is used on the same circuit which has a dimmer switch.
•
For outdoor use, please use in a minimum IP44 fixture.
Packing list
SKU#121245: 121246 globe x 2; 121247 remote x 1
Installation instruction
Install The Battery
•Slide and open the battery cover to access to the battery
compartment.
•Install 2 x 1.5VDC AAA battery in the compartment. Please make
sure the polarity of the battery is correct.
NOTE: This product is only compatible with Lucci Comfort globes.
Remote Control Buttons
:ALL ON button: Press it to turn ON all globes. Press and hold to pair all
globes with the remote. Please refer to “pairing remote with globe” section.
:ALL OFF button: Press it to turn OFF all globes. Press and hold to clear all
paired codes. Please refer to “pairing remote with globe” section.
:WARM WHITE button: press it to set the globe to a 3000K colour
temperature.
:DAYLIGHT button: Press it to set the globe to a 5000K colour temperature.
:COOL WHITE button: Press it to set the globe to a 4000K colour
temperature.
:NIGHT LIGHT button: Press it to set the globe to a night light mode.
:COLOUR TEMPERATURE DECREASE button: Press it repeatedly to
gradually decrease the colour temperature (Minimum 3000K).

Installation Instructions
2 | Page V1.1 Published on 11 2017
:COLOUR TEMPERATURE INCREASE button: Press it repeatedly to gradually increase the colour
temperature (Maximum 5000K).
:LED INDICATOR: Indicates the remote working status.
:BRIGHTNESS INCREASE button: Press it repeatedly to increase the brightness of the globe.
:BRIGHTNESS DECREASE button: Press it repeatedly to decrease the brightness of the globe
:GROUP A ON button: Press it to turn ON all globes set to group Acontrol button. Press and hold to pair
all group A globes with the group A remote control buttons. Please refer to “pairing remote with globe”
section.
:GROUP A OFF button: Press it to turn OFF all globes set to group A control button. Press and hold to
clear the paired codes of the group A remote control buttons. Please refer to “pairing remote with globe”
section.
:GROUP B, C and D CONTROL buttons: The same function as group A control button.
Pairing Remote with Globe
Install the globes to your preferred areas, then refer to the
below instruction.
To pair a globe group
•Press and hold the group A ON button , and turn ON
all globes that need to be connected to group via their
switches. The LED globes will flash 3 times slowly to
indicate the pairing process has been successful. The
button can now be released.
•When adding more globes to group A, repeat above
process.
To clear a globe group
•Press and hold the group A OFF button , and turn ON
all globes that have been connected to group A. The LED
globes will flash 3 times slowly to indicate that paired
code removal has been successful. The button can now
be released.
•Repeat above processes to complete the pairing or
clearing of the paired code for Group B, C and D control

Installation Instructions
3 | Page V1.1 Published on 11 2017
buttons.
•To clear all paired codes of groups A, B,C and D at the same time, just press and hold the ALL OFF
button and turn ON all the globes via their switches, until the LED globes flashes 3 times slowly.
Copy Remote Function To New Remote
•Press the 3000K button four times and then 5000K button one time of paired remote (1).
The LED indicator will be flashing to indicate that remote (1) has been activated to transmit its
paired code to another remote (2).
•On the new remote (2), Press the 5000K button four times and then 3000K button one
time. The LED indicator will be flashing to indicate that remote (2) has been activated to receive the
paired code from remote (1). Once the paired code copying process is complete, the LED indicator
of remote (2) will stop flashing.
•Press the night light button of remote (1) to end the remote copy paired code process.
•Repeat above process for any other remote.
•To reset the remote (2) without a paired code, just remove the battery and press any button on the
remote.
NOTE: If the pairing is unsuccessful, please refer to the above instructions and follow the clearing and
pairing processes carefully.
Specifications
SKU# 121245 (Comprised of :)
SKU# 121247 x 1
Operating Voltage 3VDC
Working Distance 10m-15m
Battery 2 x 1.5VDC AAA , not included
Working Frequency 2.400- 2.525 GHz
SKU# 121246 x 2
Operating Voltage 220-240VAC,50Hz
Power consumption 6.5W
Socket ES (E27)
Dimensions D:60mm H116mm
Average life 15000H
Colour temp Colour shifting , 3000K → 5000K
Light output 600 lumens