Lucci LEDlux LEDlux Canteen 020375 User manual

Installation Instructions
1 | Page v 1 . 1
LEDlux Canteen
SKU# 020375, 020376, 020377, 020378, 020379, 020380
Rated Voltage 220-240V~ 50Hz
Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all
instructions carefully before assembly, installation and use of this product. Please keep instructions for future reference.
Warranty
•This fitting is covered by a 3 year warranty. The warranty is from date of purchase, not the date of installation.
•If the fitting is not installed by a licensed electrician it will void the warranty.
•Please retain proof of purchase and evidence of installation by a licensed electrician for any warranty enquiries.
•The use of non-recommended dimmers may damage your LED light fitting and will void the warranty.
•Warranty will be void if there is any damage due to improper usage or modification to the fitting.
•Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void warranty.
Installation requirements
•Must be installed by a licensed electrician.
•All wiring and installation of the light fitting must adhere to local and national wiring rules.
eg. AS/NZS 3000:2007/Amendment 2:2012 Electrical installations.
•Select a suitable location for installation;
- This product is suitable for indoor use only.
- The mounting point must support 2 times the weight of the fitting.
- Ensure the fitting is not installed in direct line of an air vent/system and is not placed in any moist of damp areas.
•This fitting is dimmable and has been tested with Lucci LEDlux SKU# 290998 dimmer, Clipsal 32E450TM and
Clipsal 32E450UDM dimmers only. The use of a LED dimmer such as the Lucci LEDlux SKU# 290998 dimmer is
highly recommended.
NOTE: For the best dimming range, use with the Lucci LEDlux SKU# 290998 dimmer and adjust the variable
resistor at minimum and maximum dimming positions on the dimmer during the installation.
NOTE: The use of non-recommended dimmers may damage your LED light fitting and will void the warranty.
NOTE: Dimming may cause buzzing sounds or a slight flicker. There may be slight delays with the LED light start
up or slight uneven light performance when more than one LED light fitting is linked together, switched ON or
dimmed. This is not a product fault and as such is not covered under warranty.
NOTE: Some dimmers have a minimum load of 20W. Ensure the dimmer position is on the maximum setting before
turning on the LED light and adjust the dimmer down to your desired light level.
•Take care not to pull any electrical wires during unpacking as this may damage the connection.
•Lay out all the components on a smooth surface and make sure there are no components missing before
assembling. If parts are missing, return the complete product to the place of purchase for inspection or replacement.
•Check whether the fitting has been damaged during transport. Do not operate/install any product which appears
damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.
•Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.

Installation Instructions
2 | Page v 1 . 1
Installation directions
1. Remove all packaging material from the product and be careful not to throw away accessories that may be hidden
within the packaging material.
2. Remove the mounting bracket (B) from the canopy by loosening the screws (D) on both sides.
3. Use the mounting bracket (B) as a template to mark the screw positions onto the ceiling and drill any holes required.
4. Install the mounting bracket (B) onto the ceiling by using appropriately sized mounting screws (C) and anchors (A).
Ensure the screws (C) and anchors (A) used are suitable for the mounting surface and surrounding environment.
5. Connect the mains supply wire to the terminal block (E). Ensure the wires are secure and no bare wires are exposed.
Mains Supply Wire Fitting Wire
Earth – Yellow/Green Yellow/Green
Neutral – Blue or Black Blue
Live – Brown or Red Brown
6. Install the canopy onto the mounting bracket (B) and secure by tightening the screws (D) on both sides.
7. After the installation, switch on the fitting to test all the lighting functions and enjoy your new lighting product.

Installation Instructions
3 | Page v 1 . 1
Safety tips
•Always ensure the power is OFF and the fitting has cooled down before performing any maintenance, cleaning or
making any adjustment to the fitting.
•To avoid injury or damage to the fitting, ensure that power leads and screws are secure before connecting the power.
•Select a suitable location away from liquids and hazards.
•Ensure that the fitting does not come in contact with corrosive chemicals, etc.
•To clean, wipe with a damp clean cloth. Never soak the fitting with water.
•Handle the fitting and cover/shade with care to avoid breakage.
Troubleshooting
PROBLEM
POSSIBLE CAUSE
SUGGESTED SOLUTION
Does not work.
(New installation) Wiring loose or no power to the LED fitting.
Check your circuit breaker/safety switch box and
turn on power to your circuit.
Contact the installing licensed electrician to check if
the fitting has been installed correctly.
Does not work.
(Existing installation) No power to the LED fitting. Check your circuit breaker/safety switch box and
turn on power to your circuit.
Contact your nearest Beacon Lighting store.
Flickers when dimming.
(New installation)
Non-recommended dimmer used. Check the dimmer used. Ensure the dimmer used is
on the list of recommended dimmers in this manual.
Some dimmers have a variable
loading adjustment function. eg. Lucci
LEDlux SKU# 290998 dimmer.
This may not have been adjusted
during the installation of the dimmer.
The variable resistor needs to be adjusted to suit the
LED fitting load to reduce the flickering.
Flickers when dimming.
(Existing installation) Dimmer position on low. Ensure the dimmer position is on the maximum
setting before turning on the LED fitting and adjust
the dimmer down to your desired light level.
Buzzing sound. Non-recommended dimmer used. Check the dimmer used. Ensure the dimmer used is
on the list of recommended dimmers in this manual.
Uneven light start up Dimmer position on low when
switched on.
Ensure the dimmer position is on the maximum
setting before turning on the LED fitting and adjust
the dimmer down to your desired light level.

Installation Instructions
4 | Page v 1 . 1
Specifications
SKU # 020375 020376 020377 020378 020379 020380
Colour Black White Brushed
Chrome Copper Brass/Black Black/Brass
Rated
Voltage 220-240V~ 50Hz
Rated
Wattage 11W
LED Specs Seoul LEDs, dimmable, 3000K,650 lumens
Dimmer
Information
Lucci LEDlux SKU# 290998 dimmer (Highly Recommended)
Clipsal 32E450TM, Clipsal 32E450UDM, (Compatible)
(Please refer to the Installation Requirements or Troubleshooting section in this manual
for more information on the recommended dimmers, performance, operation and tips.)
Weight 1.0kg
Dimensions H:317mm Dia:155mm Susp:2000mm